Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCG460
Summary of Contents for DeWalt DCG460
- Page 1 DCG460...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A Fig. B...
- Page 4 Fig. C Fig. D 90˚ 90˚ Fig. E Fig. F XXXX XX XX Fig. H Fig. G...
- Page 5 Fig. I Fig. J Fig. K Fig. L Fig. M...
-
Page 6: Technical Data
English LARGE ANGLE GRINDER DCG460 Congratulations! WARNING: The declared vibration and/or noise emission level represents the main applications of the tool. However You have chosen a D WALT tool. Years of experience, thorough if the tool is used for different applications, with different... -
Page 7: Definitions: Safety Guidelines
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or Large Angle Grinder moderate injury. DCG460 NOTICE: Indicates a practice not related to WALT declares that these products described under personal injury which, if not avoided, may result in “technical data”... -
Page 8: Personal Safety
English refrigerators. There is an increased risk of electric shock if will do the job better and safer at the rate for which it your body is earthed or grounded. was designed. c ) Do not expose power tools to rain or wet conditions. b ) Do not use the power tool if the switch does not turn it on and off. -
Page 9: Kickback And Related Warnings
English f ) Do not expose a battery pack or tool to fire or If power tool or accessory is dropped, inspect for excessive temperature. Exposure to fire or temperature damage or install an undamaged accessory. After above 130 °C may cause explosion. inspecting and installing an accessory, position g ) Follow all charging instructions and do not charge yourself and bystanders away from the plane of... - Page 10 English For example, if an abrasive wheel is snagged or pinched by the Proper wheel flanges support the wheel thus workpiece, the edge of the wheel that is entering into the pinch reducing the possibility of wheel breakage. Flanges point can dig into the surface of the material causing the wheel for cut‑off wheels may be different from grinding to climb out or kick out.
-
Page 11: Additional Safety Instructions For Wire Brushing Operations
English sanding paper. Larger sanding paper extending too far • Safely dispose of the old plug. beyond the sanding pad presents a laceration hazard and • Connect the brown lead to the live terminal in the plug. may cause snagging, tearing of the disc or kickback. •... -
Page 12: Charger Operation
English nOTE: This could also mean a problem with a charger. • Do not place any object on top of charger or place the charger on a soft surface that might block the If the charger indicates a problem, take the charger and battery ventilation slots and result in excessive internal heat. -
Page 13: Storage Recommendations
English • Do not charge or use battery in explosive atmospheres, materials that could contact them and cause a short such as in the presence of flammable liquids, gases or circuit. NOTE: Lithium‑ion batteries should not be put in dust. Inserting or removing the battery from the charger may checked baggage. -
Page 14: Package Contents
Year and Week of Manufacture Battery Type Description (Fig. A) The following tools operate on a 54-volt battery pack: DCG460. WARNING: Never modify the power tool or any part of it. These battery packs may be used: DCB546, DCB547, DCB547G, Damage or personal injury could result. - Page 15 English Young children and the infirm. This appliance is not • 2. Insert battery pack into the charger as described in the intended for use by young children or infirm persons charger section of this manual. without supervision. Fuel Gauge Battery Packs (Fig. B) •...
- Page 16 English CAUTION: When using a Type 1/41/Type A (cut‑off), CAUTION: If guard cannot be tightened by adjusting Type 27/Type B (grinding) wheel guard for cutting‑off clamp, do not use tool and take the tool and guard to a and facial operations in concrete or masonry, there is service centre to repair or replace the guard.
-
Page 17: Prior To Operation
English 4. Tighten the clamp nut by hand. Then depress the spindle bystanders away from the plane of the rotating accessory lock button while turning the sanding disc until the sanding and run the power tool at maximum no-load speed for one disc and clamp nut are snug. - Page 18 English To engage the lock, depress the spindle lock button and rotate masks do not offer this protection. Refer to your local the spindle until you are unable to rotate the spindle further. hardware dealer for the proper approved mask. 3. NO EATING, DRINKING or SMOKING should be done in the Surface Grinding, Sanding and Wire work area to prevent ingesting contaminated paint particles.
-
Page 19: Maintenance
English 5. Remove the tool from the work surface before turning wheel (if provided). Expired wheels are more likely to burst the tool off. Allow the tool to stop rotating before laying and cause serious injury. Store bonded abrasive wheels in it down. -
Page 20: Rechargeable Battery Pack
• Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly. guard Types for DCg460 Type B Type A (Shallow, Grinding) (Closed cut off) Type A (Type 41) guards are intended for use with Type 41 (1A) cutting wheels and Type 42 (27A) wheels marked for cutting only. - Page 21 English Additional information for guards and Accessories for DCg460 ≤10 mm When using segmented diamond wheels, use only diamond wheels with a peripheral gap not greater than 10 mm and negative rake angle. DO NOT USE segmented diamond wheels with a peripheral gap greater than 10 mm and/or a a positive rake angle.
- Page 22 English Application Accessory Type Accessory Guard Correct Assembly Wheel Type 41 (1A) (metal) Type 1/41 Type A (Closed cut off) Wheel Type 42 (27A) (metal) Type 1/41 Type A (Closed cut off or masonry/concrete cut off wheel guard) Wheel Type 41 (1A) (masonry/concrete) Type 1/41 Type A (Closed cut off or masonry/concrete cut off wheel guard)
- Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg enduser.BE@SBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)