Safety Instruction For your safety, please read the following instruction before you use the product. Serious injury or property loss may be caused by improper operations. Do not try to repair the product without guidance. Placement Do not place the unit on an unstable cart, stand, tripod, racket, table, or shelf. ...
Normal operating temperature is 0 ~ 40℃. Humidity Do not expose machine in rain, damp or place near water. Ensure the indoor drying, cool. Ventilation Keep the ventilation openings clear. Ensure that the unit has enough space for ventilation around: left, right and back >10cm, top> 20cm.
Page 6
Step2: Expansion bolt installation Press the expansion bolt into 8 holes. (Ref. Picture 2) Step3:Wall mounting bracket A installation Install the wall mounting bracket A with 8pcs screws and gaskets. Please ensure that the wall mounting bracket A is installed horizontally. (Ref. Picture3) Step4: Install the left&...
Page 7
Use screws fix the hang bracket B at the back of IQTouch. Please check the direction of hang bracket B before installation. (Ref. Picture 4) Step5: Hang IQTouch on the wall mounting bracket A Hanging the left &right hang bracket B to the wall mounting bracket A, please ensure two hang brackets B total hang on wall mounting bracket A, then tighten the screws of hang bracket B to prevent it slide.
1.2 OPS Installation Note: The OPS does not support hot-plugging. Please insert the plug of the OPS after the interactive panel is disconnected from the power. Install the OPS by the following steps: 1) Insert the OPS into the special slot on the rear of the interactive panel. 2) Tighten the screws.
2.Enable the Device 1) Connect the power cord to the port at the back of the device. 2) Plug the power cord to the electrical socket. 3) If the power LED light is not turn red please turn on the rocker switch at the back of the device. Press power button or put the battery in to remote control and use remote control to power on the device.
3.Control Panel Item Icon Function Description IR receiver:Receive infrared signals such as remote control Power button: On or standby mode Touch USB cable to realize the touch function of external device HDMI port used to connect an external display device USB Type C: Image, power, touch, audio and video transmission USB 3.0 port (Andriod &...
5.Remote Control Button Function Description Power on/off Mute OPS computer shortcut VGA mode shortcut HDMI HDMI mode shortcut MEDIA Multi-media mode shortcut F1-F12 Correspond to computer buttons F1-F12 Input Select different input source Open/close backlight Up/down/left/right button Confirm Menu Open/close menu Esc/Exit Stop current operation or exit menu VOL+/VOL-...
Page 12
6.Remote Control Area The effective receiving area is about 3 meters with 30° angle from vertical point to the left and right. And the effective receiving area is about 5 meters from the front of device. Note that the remote control signal receiver locates at the position of power indicator.
7. Connecting and Setting For safety, please do not connect any power supply before the external devices setup. 7.1 External Computer and Touch Connecting Audio IN VGA IN USB-Touch 1) Connect a VGA cable (15 pin) between the VGA and external PC. Connect an earphone cable between the PC and audio at the same time.
7.2 AV Connecting AV IN 1) Connect an AV cable with the device with AV-OUT (Yellow is Video, Red is Audio-R, White is Audio-L). 2) Plug the POWER cord and switch it on from the rear panel. 3) Press to turn on the panel.
4) Select Signal source to YPbPr source. Front HDMI/ HDMI 1/ HDMI 2 1) Connect a HDMI cable with the device with HDMI. 2) Plug the POWER cord and switch it on from the rear panel. 3) Press to turn on the panel. 4) Select Signal source to HDMI source according to the one you connected.
7.4 RS232 1) Connect a serial port cable with the device. 2) Plug the POWER cord and switch it on from the rear panel. 3) After connecting the central control system and unit, you can use some of the function such as power on/off or adjust the volume etc.
Page 17
RS232 code list RS232 Code for Android Firmware 16-byte command, baud rate 115200 Start code 99, client code 23, function ID code, device ID code (generally 01 without special instructions), check code + function ID code = FF, end code AA Function Required Commands(Hex) Power ON...
8.Android Home Page Enter the Android interface by default after power on. It is renewed slideable three-homepage. Slide to the left, all the applications are presented. Users can view or open the APK application installed by themselves in this interface, as shown in the figure.
Slide to the right, the recent applications and screen shots are presented right there for quick access. 8.1 Floating menu 1. The icon floating on the desktop can be moved freely and displayed in any interface. 2. Add: Click the icon it will shows the pop-up menu. 8.2 Sidebar The sidebars are divided into left sidebar and right sidebar.
Page 20
Home Click icon to enter the main interface of Android system. Back Click icon to return or exit the current program. Annotation Click icon to open the annotation. Click hoose the pen color. to c Click to undo or forward the operation.
Page 21
Click to open eraser mode. Click to clean all the annotation. Click to share scan QR code. You can scan code to save the files to your own mobile device. Click to insert whiteboard. Click to exit the annotation mode. Control panel Click icon to display the notification panel as shown below.
Page 22
◾ Password unlock: touch screen to input 2580 password, and then click OK to unlock. (The initial password is 2580, the user can enter the settings to change the password.) ◾ Remote unlock: Press F9 of the remote control to quickly unlock. ◾...
Page 23
Click icon to enter the screen backlight status, touch the screen or use the button, energy save button of remote control to turn off energy saving. 11) Eye protection Click icon to turn on or off the eye protection function. 12) Sound and brightness adjustment Sound adjustment:move sound progress to adjust the volume.
Page 24
OPS: Click icon,user can switch directly to the built-in computer channel. Shut down:Click icon,the display powers off. Setting :Click icon to enter the system settings interface. Input Click icon to show the source channel list, and the user can switch channel.
9.Android Settings Click setting icon on home page to enter Android setting interface. 9.1 Individualization Basic You can adjust the system's sound and brightness, change the system theme wallpaper, modify the device name and view the system application on basic settings interface. Equipment Name : Users can modify the name of the interactive display.
Page 26
Wallpaper Wallpaper has live and dynamic wallpaper. It also can be added by custom. Custom added wallpaper can be stored in live wallpaper and deleted by long press.
9.2 Network Wired network Under the wired network interface, users can view the MAC address, IP address and other information. The automatic access to the IP address is opened by default, and the parameters such as the IP address and the subnet mask can be manually modified after the automatic acquisition is closed.
Page 28
Hot spot Under the 2.4 and 5G hot spot settings interface, users can change the hot spot name, security, password and other parameters. Notice: 2.4G and 5G hot spot, 2.4G hot spot and wireless network can neither be opened at the same time.
9.3 Intelligence Timing switch After setting the power-on time and power-off time, the system will automatically power on or off when the scheduled time is up. Channel settings Click to set Power on Channel or click to custom channel name.
Page 30
Security settings USB lock, screen lock, and application lock can be turned on or off. You can also set the corresponding unlock password, the initial password is 2580. Click Set Password to change the corresponding password. Application management All applications in the list can be managed, click to setup the corresponding applications.
More functions You can set the suspension menu, sidebar, environmental sensitivity, centralized control, three- finger off screen and five-finger follow. 9.4 System The system setting options are mainly for system input method, language display setting, system update and upgrade, etc., as well as system version information and built-in storage usage. Language and typing Click to set the language ( English, Arabic, Spanish, French, Italian, Japanese,...
Page 32
Time and date Turn on the Auto set time. If the network connection is successful, the current network time will be automatically synchronized. When the Auto set time is off, you can manually set the date and time. Click to change the time. Voice Adjust volume and set sound mode, output device.
Page 33
System information You can view the system version information and built-in storage usage and other information. System update 1) Restore factory settings: click Reset to restore the factory settings. 2) Local update: Copy the firmware to the root directory of the U disk, insert the U disk into the multimedia USB interface of the machine, and select local upgrade and update.
10.Whiteboard App 10.1 Interface Display Click the whiteboard icon in the main interface to start the whiteboard software. 1. The whiteboard is selected by default and can be written directly. 2. Support single point mode and multi-point mode, multi-point support up to 20 points. 3.
10.2 Menu Click (menu icon) in the lower left corner of the interface,pop up display and display the lower content menu. Content menu icon function operation instructions: (1) Open the file : Click the icon to open and save the file under the whiteboard file directory (the default path directory is built-in storage / writeboard), click the file to open directly, and you can edit and save again.
Page 36
(2) Save the file: Click the icon to save the current writing content. The default time is named and saved. The user can customize the name to save. The user can select the built- in storage or U-disk to save the whiteboard file. (3) Export: Click the icon to export the content written on the whiteboard in the image format *.
Page 37
(4) Insert: Click the icon to open the local storage or U disk image file, the user can select the image to insert on the whiteboard, and the picture can be marked and written. (5) Email: Click the icon. When using the email sending function for the first time, you need to set the email sender's email information in the email login interface, as shown in the figure: a.
Page 38
b. After successful login, the user enters the email address of the recipient, and then click send to record the contents on the whiteboard. Pdf format file is sent to the recipient's mailbox, and click settings to modify and replace the current account number.
Page 39
(8) Exit: Click the icon to exit the whiteboard when there is content on the whiteboard. A prompt will pop up: the whiteboard has not been saved. Do you want to save the whiteboard and exit the whiteboard. According to whether to operate the function or not; if the whiteboard has no content, click exit whiteboard.
10.3 Aid tools The system has its own ruler, compass, and can be inserted into the system's calendar, camera, screen, calculator, timer and spotlight gadget. When the ruler is selected, the ruler tool appears on the screen, which can draw lines and mark the scale of lines.
When selecting the calendar camera and other gadgets, the whiteboard application calls the application directly. 10.4 Scan code sharing Code scanning and sharing: Click the icon and select the sharing type. When the network is connected, a two-dimensional code window can be generated, and the current conference record can be swept away through the wechat scan function;...
Page 42
After the QR code is generated, the display is shown in the following figure. Click the lock icon to start the QR code lock mode, and the password is displayed next to it. After scanning the QR code, you must input the password before you can view the file.
10.5 Common Function Brush tools (1) Click the icon to call up the brush tools menu. (2) Change brush thickness and color. Click the dot icon above to modify the stroke thickness, click the color box to select the brush color, and click the custom icon to expand the color palette to customize the brush color.
Page 44
Shape Click to , pop up the graphic and image selection box. When the selected graph is drawn on the screen, it will be displayed as the corresponding figure. Click on the picture to insert the picture you just clicked on the screen.
Page 45
Background Click to change the background color of whiteboard. Picture shape...
Page 46
Background image Revocation and restoration (1) Undo: icon to undo the previous operation. At most 50 steps can be undone at a time; (2) Restore: Click the icon to redo the operation that has been revoked. The maximum recovery steps are 50 steps at a time.
Page 47
Select function Click to select the selection function, and the interface switches from writing mode to selection mode. The handwriting and shape in the interface can be drawn, and then the functions of moving, deleting, copying and pasting can be realized for the inserted pictures. Move, delete, copy and paste, rotate and zoom.
Page 48
Left and right switching function Click the icon to switch the left and right positions of more function icons, code scanning and switching function icons with the function icons on the upper and lower pages, page preview function icons and page adding function icons. Page preview (1) Open the page preview pop-up window: Click to show that the current page is selected.
Page 49
(2) Add page: Click the icon to add a page. (3) Delete page: In the open page preview window, click the delete button in the upper right corner of the page thumbnail to delete the page or click at the bottom of the page preview window to delete all pages.
Page 50
Delete page or delete at the bottom of page preview window, press to delete all pages. Click icon to enter all page display mode. (4)Page turning function: Click the left and right page turning button and icon to realize page turning effect. In the page preview window, if the preview page exceeds the Limited Preview range, slide up and down quickly;...
11. Screen Share 11.1 Application note The main function of this application is to wirelessly transmit the content of mobile phones, tablets or computers to the display, and truly achieve the wireless screen transmission function of the projection device and the projected device (note: mobile phones, tablets or computers need to be on the same local area network).
2. Function activation Activate it only through connecting network if you have purchased EShare serial number. 3. Operating description 1) Android mobile phone connection network, scan the multi-screen interactive interface QR code to download and install E-share application software (Apple mobile phone does not need to download);...
Page 53
Click icon, user can modify the device name In this interface, you can modify the device name and set the connection password. when an Android phone connects to touch screen, it needs to enter the connection password to connect to the screen.
11.4 Webcast remote screen sharing Click Enable Webcast to obtain the IP address for visitor on the center place of the current page. Open browser and input the IP address to share your personal screen from different places with no requirement of the same LAN.
Page 55
1. IQShare button should be paired with Touch screen The USB port of IQShare button should be inserted into Touch screen and paired with touch screen. The touch screen will display paired successfully after few seconds. Note: A. A Touch screen can be paired with up to 8 IQShare buttons in the same network environment. B.
Page 56
12.Built-in PC Operation 1) Select PC signal source to enter PC interface. The following are three ways to select a signal source channel. Swipe your finger up from the left and right side to bring up a toolbar then click input. ...
Page 57
13.Troubleshooting Remote Control Check whether there is object between remote control and panel receiver; Remote control out of order Check whether the battery is installed correctly; Check whether the battery is drained. Touch Make sure infrared frames have not been obscured. ...
Page 58
Check the color system. This is the general user manual for all IQTouch TE1100Pro interactive touch screens. Some details may be different from the actual product.
Need help?
Do you have a question about the IQTouch TE1100Pro and is the answer not in the manual?
Questions and answers