Related Manuals for ADVANCED UV LIGHT Future Sun HP
Summary of Contents for ADVANCED UV LIGHT Future Sun HP
- Page 1 ™ Sunlamp Model HP 24/21: HELIX US: "Future Sun HP" Owner's Manual Vers. 1/April 2005...
- Page 2 HELIX™ equipment combining peak performance with a (US Tradename: "Future Sun HP") - in the clear, modern design. following referred to as HP 24 or "the sunbed" - in a safe and proper way.
-
Page 3: Table Of Contents
Error! Style not defined. Table of Contents Safety Instructions........4 Safety Instructions – Further Details ..... 4 Obligations of the Operator/Owner......4 Proper Use of the Sunbed ........5 Improper Use ............5 Notice of Residual Risks ........5 Basic Safety Instructions ........6-7 Safety Instructions for Users......... -
Page 4: Safety Instructions
These hints contain information on the use of the sunbed. Obligations of the Operator Advanced UV Light is not responsible for damages caused by improper use of the sunbed or disregard of the instructions provided in this manual. • The operator of this sunbed must ensure that... -
Page 5: Proper Use Of The Sunbed
• by persons suffering from diseases • by persons disregarding recommended exposure times • by persons not wearing protective eye-wear are improper uses of the sunbed and may cause personal injuries. Advanced UV Light GmbH is not responsible for injuries due to improper use. -
Page 6: Basic Safety Instructions
• Smoking and open flames are prohibited within • Service personnel of Advanced UV Light GmbH proximity of the sunbed. and its authorized distributors' are considered as • Do not exposure materials that may suffer trained staff with the necessary expertise. -
Page 7: Safety Instructions For Users
• All maintenance instructions and –intervals must be diligently observed Safety Devices • Use only original spare parts as provided by Advanced UV Light GmbH or its authorized distributors. In any other case you need Emergency Stop Button authorized service personnel to approve of these... -
Page 8: Delivery
Error! Style not defined. Delivery On delivery you will receive 1 box fixed to a wooden pallet and 3 additional boxes. All pieces show markings detailing the contents of the boxes. Check boxes immediately for signs of any transport damages. Inform forwarder immediately if you notice any relevant and obvious damages. -
Page 9: Technical Data
Error! Style not defined. Technical Data Please see also technical data on the type label. For Northamerican equipment and other overseas export units see separate data sheets enclosed as an Attachment to this manual Dimensions Depth 1610 mm Length 2295 mm Height (top closed) 1445 mm Height (top open) -
Page 10: Room Requirements
Error! Style not defined. Room Requirements Required space for operation and maintenance min. 2,5 x 2,5 m Floor, level, load capacity min. 1,8 kN/m Ambient temperature +10 °C bis +30 °C Relative humidity max. 65% The Control Panel Tanning Session Start / Stopp AC unit On / OFF Display... -
Page 11: Transport
Error! Style not defined. Drive the load carefully to the place of Transport installation. Transport with a trolley DANGER 4 persons lift a single box onto the trolley. Transport of the unit must be performed by authorized and skilled Roll the box carefully to the place of installation. personnel. -
Page 12: Assembly And Electrical Connection
Error! Style not defined. In order to remove the unit from the wooden Assembly and electrical pallet, the unit must be disassembled and Connection carried to the site of installation. For disassembly and transport of single components four (4) persons are necessary. WARNING Removal of packing material FAULTY ASSEMBLY! - Page 13 Error! Style not defined. Removal of transport brackets Remove the AC plexi Unscrew the bracket which fixes the unit to the Two persons lift the AC plexi out of the sunbed. pallet (transport bracket). Store the AC-plexi on soft padding material. Remove lamp covers at head- and footend Pull out the ballast tray for approx.
- Page 14 Error! Style not defined. The lamp cover at the footend is not connected Lever the screwdriver and lift the ball-bearings to a plug. Just take out the lamp cover. out of the fork Removal of air vents Attention! At the headend of the sunbed, there are two air Take care that you do not scratch vents.
-
Page 15: Assembly
Error! Style not defined. Disassemble sunbed from pallet WARNING! Loosen the hexagonal screws at the right and Check if the local supply system left angle on the metal groundplate. The female complies with the data on the type screws are on the reverse side of the pallet. label at the rear side of the sunbed. - Page 16 Error! Style not defined. WARNING! The unit must be grounded, else there is a risk of electrostatic load. When touching the unit or when standing very close to it there is a risk of an electric shock. WARNING! The first start-up of the unit must be performed by an authorized service technician.
- Page 17 Error! Style not defined. Assembly of Exhaust Air Stacks At the rear side of the sunbed there are two (2) air outlets (1 and 2). On these outlets you install the exhaust air stacks. The air stacks are packed into a separate box and contains the following parts •...
- Page 18 Error! Style not defined. Assembly of air vents at the Top Canopy At the headend of the top canopy there are three air vents. The air vents consist of the following components: • three air vents • three adjustable air nozzles •...
- Page 19 Error! Style not defined. Assembly of lamp covers at the head- and footend of the sunbed Take the lamp cover for the headend and put the plug for the safety switch into the plug terminal until you can hear it “click” in. If you have disassembled the four segments of the ballast tray, re-install and fix them.
- Page 20 Error! Style not defined. WARNING! When moving the ballast tray, take care that wires and cables do not get pinched and damaged. In case of damage blank wires can get into contact with other metal parts of the unit and cause an electric shock. Push the ballast tray into the sunbed and take care that cables and wires do not get pinched or damaged.
-
Page 21: First Start-Iup
Error! Style not defined. operating hours only!) Customized set-ups are also Fix the design element with the screws to the top canopy. performed in this mode. Turn the mains disconnection switch into position „I“. Push the acrylic of the sunbed upwards and secure with supplied bracket. - Page 22 Error! Style not defined. In the program mode, you can select individual menue options by a combination of entries at the control panel. Facial Switch +/– with this switch you can select individual menue options. Body cooling With this switch you can change values switch –...
-
Page 23: Set Up Of Electronic Controls
Error! Style not defined. Set-Up of Electronic Controls Menue Value Description Display Pre-Set Switch (Start-Stop) + Test Run 60 sec. 0060 – Switch AC – Hour meter xx xx No re-set option Switch (Start-Stop) – Operating hours – low-pressure lamps Switch (Start-Stop) –... - Page 24 Error! Style not defined. The following set-ups can only be changed by authorized service personnel! Menue Value Description Display Pre-Set – No function 01-60 Maximum operating time (automatic safety switch-off) in minutes 00-03 Facial lamps down to level xx 00-06 Facial lamps time-out in minutes 01-03 Facial lamps ignition level at start-up...
-
Page 25: Operation
Error! Style not defined. The Emergency Stop Button Operation In case of danger the unit can be shut off immediately by pushing the Emergency Stop Danger Button. All radiation sources (low-and high- UV-RADIATION! pressure lamps) are stopped immediately. The main ventilation (sunbed cooling) stops with a UV-radiation can cause serious eye delay time. -
Page 26: Control Set Ups - Options
Error! Style not defined. Control Set-Ups - Options AC Unit unit guarantees comfortable even Facials temperature. When starting the The intensity of the facials can be sunbed, the AC-unit turns on increased or diminished in certain automatically. steps. When the AC-unit is activated, The illuminated diodes show the the diode at the AC-button lights selected intensity level. -
Page 27: The Definition Of Skin Type
Error! Style not defined. Recommended exposure time for model Definition of Skin Type HD 24/21 – standard configuration. In order to select your tanning program and For non-standard configurations or Northamerican maximum exposure time, it is necessary to define Export units, please see separate attachement. your skin type. -
Page 28: Maintenance
Failure (no fan noises) ATTENTION! For maintenance and service use only original spare parts as Annual Inspection provided by Advanced UV Light (or every 800 hours of operation whatever GmbH or authorized distributor. occurs first) Inspections for mechanical and technical safety of... -
Page 29: Replacement Of Low-Pressure Lamps & Starters
Remove and dispose of defective or aged low- lamp does not ignite. pressure lamps. Advanced UV Light recommends to replace Assembly starters with every second lamp change. Turn in the new starter clockwise by 90° into Disassembly the lampholder. -
Page 30: Replacement Of Top Plexi
Error! Style not defined. Replacement of Top Plexi Take a screwdriver and put it into the spring slot (1) at the top canopy and push the profile (2) inwards. Set the frames for the air vents into the new top plexi. Reassemble the new top plexi. - Page 31 Error! Style not defined. Disassembly CAUTION GLASS BREAKAGE! Glass breakage can cause cuts and hand injuries. It is recommended to wear protective gloves. Make sure that the unit is completely shut off from the mains supply and secured with lock and key against unauthorized and accidential ATTENTION! activation.
-
Page 32: Replacement Of Filter Glasses
Error! Style not defined. Replacement of filter glasses Replacing Dust Filter Mats in the Top Canopy The filter glasses must be replaced whenever there are any sign of breakage or scratches. Take the old filter mats out and replace with new ones. - Page 33 Error! Style not defined. Screw the design element back to front cover plate. Top Canopy Take a screwdriver and loosen the screws at the design element. Take off the design element. Take the fluorescent lamp out of the lampholder and replace with new one. Screw the design element back to the top canopy.
-
Page 34: Cleaning
Error! Style not defined. DANGER Cleaning Risk of Electric Shock! DANGER Disconnect unit completely from mains supply system prior to any Risk of Electric Shock! cleaning maintenance job. Secure mains disconnection switch Disconnect unit completely from with lock against mains supply system prior to any unauthorized accidental cleaning... -
Page 35: Storage
Error! Style not defined. Troubleshooting Storage If you intend not to operate the sunbed for a Caution! considerable time, should store equipment at a dry place, protected from dust and Malfunctions and defects should corrosion. only be repaired by authorized service technicians! Salon personal Switch off the mains disconnection switch. -
Page 36: Error Codes
Error! Style not defined. One or more HID quartz HID Quartz lamp defective. Error Codes lamps do not light up. Error Code Possible cause and Replace HID quartz lamp. correction Ignitor for HID quartz lamp E001 Wind flag does not work.. defective.. -
Page 37: Contact To Manufacturer
Warranty Declaration of Conformity The scope and terms of warranty for this sunbed manufactured by Advanced UV Light GmbH comply with the legal provisions at the time of sale Advanced UV Light, Ruhrtalstrasse 85-93, D– effective in the country of origin. In addition, our 45239 Essen herewith declares this product to be General Terms or Trade apply.
Need help?
Do you have a question about the Future Sun HP and is the answer not in the manual?
Questions and answers