Related Manuals for Akerstroms Sesam 800 RXM
Summary of Contents for Akerstroms Sesam 800 RXM
- Page 1 OPERATING MANUAL SESAM 800 MOBILE WINCH M6, M4, RXM Original Instructions 943549-000 EN F2...
-
Page 2: Table Of Contents
2 (28) Table of Contents Introduction ����������������������������������������4 Scope ���������������������������������������������4 Service ��������������������������������������������4 Maintenance ����������������������������������������4 Technical Specifications ������������������������������5 Short Description of the System �����������������������6 Receiver �������������������������������������������������� 6 Transmitters ����������������������������������������������� 6 Screw Sizes ����������������������������������������������� 6 Description of the Receivers ��������������������������7 Description of the Receivers to ATV Winch ��������������8 Installation of the Assembled Connection Cable �������������������... - Page 3 3 (28) List of figures Figure 1. Sesam 800 RXM 12/24 V DC to ATV winch with cable installed.. ���������� 8 Figure 2. Sesam 800 RXM 12/24 V DC to ATV winch without cable �������������� 10 Figure 3. Jumper in the left position and lower position. ������������������������ 13 Figure 4.
-
Page 4: Introduction
Introduction 4 (28) Introduction This manual only covers the installation of the Sesam radio remote winch control system. The Sesam does not implement a complete con- trol system: it provides only the set of outputs that are driven accord- ingly to the actions performed by the operator of the transmitter. The way the set of outputs is used for controlling the outputs depends on the specific installation and is out of the scope of the Sesam 800 Mobile system. -
Page 5: Technical Specifications
Transmission principle: GMSK, TDMA, Operating Temperature: -25°C - +75°C Storage Temperature: -40°C - +85°C Receiver specifications Sesam 800 RXM IP- class: IP67 Power Supply 12/24 V DC 25 mA (SELV), Must be fused with a 3A blade fuse. Max switching capacity of... -
Page 6: Short Description Of The System
Short Description of the System 6 (28) Short Description of the System Receiver Main features: • 6 outputs. • Waterproof (IP67). Applies only those supplied with installed cable. • Possibility to control the outputs by external con- nections, applies only the ATV winch. Transmitters There are two different transmitters that can be used for winching applications:... -
Page 7: Description Of The Receivers
Description of the Receivers 7 (28) Description of the Receivers There are two different receivers for winch system. They come in some different variations. Receivers to ATV winch • With assembled cable with plug (IP67) • With assembled cable without plug (IP67) •... -
Page 8: Description Of The Receivers To Atv Winch
941551 PB-Free 416-1 PCB1 Figure 1. Sesam 800 RXM 12/24 V DC to ATV winch with cable in- stalled. The models indicators, connections and jumper. 1. Power LED 2. Ground, 0V (-) 3. 12/24 V DC power. Fuse with 3A blade fuse near the battery. -
Page 9: Installation Of The Assembled Connection Cable
Description of the Receivers to ATV Winch 9 (28) Installation of the Assembled Connection Cable The receiver is equipped with a 12 multicore cable for connection to the winch, voltage, etc. The cable is fused with a 3A blade fuse near the battery connection. -
Page 10: Installation Of Non-Assembled Cables
PB-Free 416-1 PCB1 Figure 2. Sesam 800 RXM 12/24 V DC to ATV winch without cable 1. Ground, 0V (-) 2. 12/24 V DC power Fuse with 3A blade fuse near the battery 3. Internal supply to the outputs (see section 8.1) 4. - Page 11 Description of the Receivers to ATV Winch 11 (28) 8.2.1 Installation of Non-assembled Cables to ATV Winch For connection of cable, should at least a 12 conductor multicore cable with outer diameters of 6-12 mm be used. The cable must be specified for an outside temperature of +80°C and each conductor must be at least 0.75 mm .
- Page 12 Description of the Receivers to ATV Winch 12 (28) 8.2.2 Installation of External Inputs to ATV Winch The receiver is equipped with four external inputs for manual cable control of in/out functions. These inputs have priority over radio con- trol. To enable them see section 8.3. To connect to the input card the leaders have to be crimped with a crimping tool.
-
Page 13: Cable Control
Description of the Receivers to ATV Winch 13 (28) Cable Control The receiver outputs can be activated by using the cable control. If the cable control is used, all radio-controlled outputs will be blocked for 5 seconds after each command from the manual cable control. Figure 3. -
Page 14: Description Of The Receivers To Forestry Winch
14 (28) Description of the Receivers to Forestry Winch Figure 4. Sesam 800 RXM 12/24 V DC to Forestry winch with cable installed. The models indicators, connections and jumper. 1. Power LED 2. Ground, 0V (-) 3. 12/24 V DC power Fuse with 3A blade fuse near the battery 4. -
Page 15: Installation Of The Assembled Connection Cable
Description of the Receivers to Forestry Winch 15 (28) Installation of the Assembled Connection Cable The receiver is equipped with three cables, two with valve connectors and one voltage cable. The voltage cable is fused with a 3A blade fuse near the battery. -
Page 16: Installation Of Non-Assembled Cables To Forestry Winch
Description of the Receivers to Forestry Winch 16 (28) Installation of Non-assembled Cables to Forestry Winch Figure 5. Sesam 800 RXM 12/24 V DC to Forestry winch without cable 1. Ground, 0V (-) 2. 12/24 V DC power. Fuse with 3A blade fuse near the battery 3. - Page 17 Description of the Receivers to Forestry Winch 17 (28) 9.2.1 Installation of Non-assembled Cables to Forestry Winch For connection of cable, cable with outer diameters of 6-12 mm should be used. The cable must be specified for an outside temperature of +80°C and each conductor must be at least 0.75 mm .
-
Page 18: Indicators On The Receiver
Indicators on the Receiver 18 (28) Indicators on the Receiver 10.1 LED Indicators The receiver has LED indicators that indicate different parameters (see Figure 1, for positions of the LEDs). The indications on the LEDs are as follows: Power LED ( Indicates whether the receiver is powered. -
Page 19: Table 5. Output Leds Connected To The Functions
Indicators on the Receiver 19 (28) 10.1.1 Outputs LED’s Indicates the state of outputs 1-6. Output LED 1 is at the bottom, output LED 6 is at the top. An activated output is indicated by a LED in ON in Figure 1). state. -
Page 20: Installation Of The Receiver
Installation of the Receiver 20 (28) Installation of the Receiver The permanent installation of the receiver must include fuses that pro- tect the equipment and wiring from over current and short-circuit. The power supply to the receiver must be fused with a 3A blade fuse. 11.1 Mounting Steps: Step 1... -
Page 21: Figure 6. Configuring Internal Supply Of Output Power
Installation of the Receiver 21 (28) 941551 PB-Free Configuring internal supply of output power Figure 6. The relationship between buttons and outputs are described in table 8. Table 8. Relationship between buttons and outputs Output Button M6 6 Button 5, output 6: is an alternating function that fits the control of lights, etc. - Page 22 Installation of the Receiver 22 (28) Step 3 1. Press button 2 ( ) on the transmitter until the green indica- tor lights. The transmitter is now active. 2. Press the Learn / Erase button on the receiver until LED 7 is ON. 3.
-
Page 23: Description Of The Transmitter
Description of the Transmitter 23 (28) Description of the Transmitter Sesam 800 M6, 6 button transmitter Figure 7. Sesam 800 M6 transmitter indication and buttons. 1. Status LED 2. Button 1-6 Sesam 800 M4, 4 button transmitter Old version: Sesam 800 M3, 3 button transmitter 1. -
Page 24: Indications On The Transmitter
Indications on the Transmitter 24 (28) Indications on the Transmitter The transmitters are equipped with a status LED indicating the status of the transmission during operation (see Figure 7 and Figure 8). 13.1 Normal Operation Quick flashing RED LED = Output is not activated and there is no feedback from the receiver. -
Page 25: Deactivating The Transmitter
Operation 25 (28) 14.2 Deactivating the Transmitter To prevent unintended activation the transmitter shall be turned off when not used. Turn off the transmitter by pushing button 2/5 ( OFF F ) for three sec- onds; the indicator flashes a couple of quick RED to finish with a long RED. -
Page 26: Receiver Drill Measures
Receiver Drill Measures 26 (28) Receiver Drill Measures 120 mm 102 mm Figure 9. Receiver Drill Measures The receiver shall be attached with 4 mm screws that are suitable for the surrounding environment Sesam 800 Mobile Winch Version: F2 Document-ID: 943549-000 EN Author: SH... -
Page 27: Replacing Batteries In Sesam 800 M6 & M4
Replacing Batteries in Sesam 800 M6 & M4 27 (28) Replacing Batteries in Sesam 800 M6 & M4 If the status indicator on the transmitter indicates low battery, replace the batteries promptly. Before changing the batteries note that chang- ing of batteries must take place in a clean environment free from static electricity. - Page 28 Åkerströms Björbo AB | Box 7, Björbovägen 143 | SE-786 97 Björbo, Sweden Phone +46 241 250 00 | frontoffice@akerstroms.se | www.akerstroms.se...