Advertisement
Quick Links
dual program
MODEL :
TM340 / TM341 / TM342 / TM348
AC: 100 – 240V
0.15A @ 240V / 0.28A @ 100V
DC: 12V
1 x 12V
+
-
STD / AGM-MF / GEL
3 - 50Ah
Automatic charger for 12V lead-acid batteries
PROGRAM 1 - STANDARD / DIRECT CHARGE : 9 STEPS
1
2
Low Volt
PULSE
Start (0.5V)
'wake up'
PROGRAM 2 - CAN-bus (BMW) : 8 STEPS
1
2
CAN-bus
CAN-bus
'wake up'
low volt
pulse
check
copyright © 2016 TecMate International – TM34x-IN1-161115
50-60Hz
1A
(max. Ah rating based
on 48 hour charge).
3
4
SAVE
TEST
sulphated
before charge
battery
3
4
TEST
Pulse
before charge
SAVE
4
INSTRUCTIONS FOR USE
IMPORTANT: Read completely
before charging
5
6
Pulse
Controlled
SAVE
CHARGE
5
6
Controlled
CAN-bus
CHARGE
OPTIMIZE
7
8
TEST after
OPTIMIZE
CHARGE
maintenance
7
8
CAN-bus
OptiMate
TEST after
'365'
maintenance
CHARGE
9
OptiMate
'365'
Advertisement
Related Manuals for TecMate Optimate4 TM340
Summary of Contents for TecMate Optimate4 TM340
- Page 1 PROGRAM 2 - CAN-bus (BMW) : 8 STEPS CAN-bus CAN-bus CAN-bus OptiMate TEST Pulse Controlled CAN-bus ‘wake up’ low volt TEST after ‘365’ before charge SAVE CHARGE OPTIMIZE maintenance pulse check CHARGE copyright © 2016 TecMate International – TM34x-IN1-161115...
- Page 2 LEDs MAINTAIN CHARGE SAVE Program LEDs 100-240Vac 1: STD 2: CAN-bus TEST SAVE CHARGE TEST MAINTAIN 15m - 2h 48h max 30m - 12h TEST LEDs 100% 100% Change program: Standard CAN-bus 10 sec.
- Page 3 IMPORTANT SAFETY dual program INSTRUCTIONS FOR CANADA & USA THIS PORTION OF THE MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS FOR THE OPTIMATE 4 BATTERY CHARGER. IT IS OF THE UTMOST IMPORTANCE THAT EACH TIME, BEFORE USING THE CHARGER, YOU READ AND EXACTLY FOLLOW THESE INSTRUCTIONS.
-
Page 4: Preparing To Charge
12. PREPARING TO CHARGE 12. PREPARING TO CHARGE 12. PREPARING TO CHARGE a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery first. a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery first. a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery first. - Page 5 dual program dual program AUTOMATIC DIAGNOSTIC CHARGER FOR 12V LEAD-ACID BATTERIES. AUTOMATIC DIAGNOSTIC CHARGER FOR 12V LEAD-ACID BATTERIES. DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES. DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES. IMPORTANT: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THE CHARGER IMPORTANT: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THE CHARGER This appliance can be used by children aged from 8 years and above and persons with reduced This appliance can be used by children aged from 8 years and above and persons with reduced...
- Page 6 CAN-bus – the POWER LED#1 remains on and DESULFATE LED#3 and CHARGE LED#4 briefly flash together at regular intervals. POWER ON: LED #1 - Confirms AC power supply to the charger. HIGH and LOW intensity indication: The"POWER ON" LED #1 will indicate brightly when current is delivered to the battery. The "POWER ON"...
- Page 7 STEP 5 Engages if the battery state of charge was 50% or higher (as tested in LED #4 : YELLOW STEP 3) or once the battery has been sufficiently recovered during STEP 4 CHARGE (5). A constant current of 1A up to a voltage of 14.2 -14.4V is delivered to the battery. NOTE CAN-bus: The program automatically resets 2 minutes after manual Standard: disconnection, OR if the vehicle CAN-bus system has de-activated the controlled 12V...
-
Page 8: Limited Warranty
TecMate (International) SA, B-3300 Tienen, Belgium, offers this limited warranty to the original purchaser at retail of this product. This limited warranty is not transferable. TecMate (International) warrants this battery charger for three years from date of purchase at retail against defective material or workmanship. If such should occur the unit will be repaired or replaced at the option of the manufacturer. -
Page 9: Product Information
PRODUCT INFORMATION Certification / Conformity Holder: TecMate (International ) S.A. , B-3300 Tienen, Belgium Issued by: TUV SUD Product Service GmbH, DE (Safety and EMC) Safety (CE-LVD) : Low voltage directive 2006/95/EC; EN 60335-2-29:2004/A2:2010; EN 60335-1:2012/A11:2014; EN 62233:2008 Safety (NRTL) : UL 1236:R2011;... - Page 10 optimate1.com OptiMate HOOK TS-252 4.5mm / 3/16” L ≥ 25mm / 1” 1.8m / 6ft max. OptiMate CABLE Extenders O-03 3.6m / 12ft O-13 6.6m / 21ft...