Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hyundai power products HYBV2600X
Summary of Contents for Hyundai power products HYBV2600X
- Page 1 LEAF BLOWER VACUUM & SHREDDER HYBV2600X Operating Instructions...
- Page 2 Introduction Index Introduction Learn How To Operate Your Machine Safely Thank you for choosing a Hyundai Power Prod- Personal Protective Equipment ....2 uct, I trust it will provide you with many years of Prior to starting.
-
Page 3: Personal Protective Equipment
Learn How To Operate Your Machine Safely The Hyundai HYBV 2600X machine is It is essential to wear When the fan door is designed to clear dry leaves and light head, eye and ear pro- open the shredding debris from gardens, paths, sports areas tection to defend against blades will be exposed and hard-standings. -
Page 4: Prior To Starting
Starting The machine requires a Prior to starting combination of 40 parts Make sure the area you’re going to work Under no circumstances should the unleaded petrol to 1 part in is safe. Wearing the necessary protec- motor be started if the machine has not semi-synthetic two stroke been fully assembled for use and safety tive equipment, place the machine on the... - Page 5 or that the engine note has changed the airways may have bocome blocked. Please stop the machine immediately by switching the red button on the upper handle to off and empty the collector bag. Whilst it is open, see if the curved pipe which connects it to the powerhead is blocked and if it is, clear it by pulling the material out with a gloved hand.
-
Page 6: Unboxing Your Machine
Health and Wellbeing Keeping your machine clean and in good It is very important that you make certain working order will help to ensure your that you don’t collect items which could safety whilst you’re using it so please harm you or damage the machine, refer to the maintainence guide in this especially hot or abrasive things. -
Page 7: Risk Assessment
Risk Assessment Now that you’ve read about some of the correct procedures you should follow, before you learn how to assemble the machine we would like you to carry out a risk assessment. Prior to carrying out any procedure e.g. assembling the machine, fuelling or starting and using it, you will benefit from conducting a risk assessment. - Page 8 Components Collector components, including zipped bag with shoulder strap, vacuum tubes and M5 connecting nuts and bolts. The nuts have a machined shoulder or integral washer. Two stroke motor unit, with fuel mixture bottle, M6 bolts Blower tubes, double ended screwdriver and connecting with Nyloc nuts, plug spanner #3 Allen key.
- Page 9 Engine and Power Head controls Throttle Friction throttle On/Off switch Upper handle Location of spark plug Air filter & fuel primer bulb Choke Vacuum door Pull starter catch Fuel tank and Exhaust filler (hot) Serial number Lower handle for Outlet to blower Hinged air inlet door use with collector/ tubes or collector...
- Page 10 Assembly for use as a collector and shredder...
- Page 11 Material collector flow diagram (pre-assembly) Velcro strap Zip, closed during operation and opened for emptying Air passes out through filter, material is re- tained in bag Material blown into bag Blower Powerhead Suction Collected material Dry material collected from shredded as it ground enters the powerhead...
- Page 12 Shredding blades Insert flat blade end of screwdriver into With the intake cover open you can see With the moulded keyway at joint with lower square hole and push to release air the blades that will shred the material as pipe at 3 o’clock, engage the collector tube intake cover catch and open door.
- Page 13 M6 bolts only fit on one side Align moulded keyway with slot in pow- Fasten Velcro strap to secure pipe. Insert the two Nyloc M6 nuts into the loca- tions on one side of powerhead and the bolts erhead and insert curved tube until the into the other, tighten until they’re just firm .
- Page 14 Assembly for use as a blower...
- Page 15 Blower flow diagram (pre-assembly) Powerful motor turns fan which expels air down tube Air leaves tube at high velocity and blows material forward Air is drawn into powerhead through vents...
- Page 16 Prior to assembly please ensure that the Identify the first-stage blower tube by the Align the keyway and push the blower air intake cover is locked closed. blue Hyundai logo and the keyway at one tube into the powerhead. end which fits into the powerhead. Push Elongated Round...
- Page 17 The machine is now assembled and is operated using one hand. Put a little grease on the screw and tighten it firmly.
-
Page 18: Starting The Engine
The Engine Fuel and fuelling Shake the fuel/oil mixture before use, through the carburettor, you’ll hear and every time, to ensure the oil is well dis- feel the change from air to liquid. Your machine is fitted with a two-stroke tributed. - Page 19 Adjusting the engine idle the choke lever. The air resting position. Let the engine run for a filter is a soft sponge-like few moments to reach its correct work- speed ing temperature. Squeeze the throttle material which is held in The idle speed of your beneath the handle with your index finger position by supporting...
-
Page 20: Replacing The Fuel Filter
0.6 mm - 0.7 mm driver and lift it off. You will now see the Carefully examine the threads are not crossed. After about four spark plug lead and insulated cap. plug’s electrode, this is rotations the plug will be seated at which Hold the cap with your where the spark occurs point you should tighten it, either firmly... -
Page 21: Maintenance And Care
pipe. Squeeze the clip with long-nosed Torque the retaining nut Service items pliers, pull the filter off and fit the replace- to 20Nm. Relocate the ment. cover and tighten the five • Spark plug If you find that you need screws. -
Page 22: Specification
Specification Displacement 25.4cc Fuel Unleaded Petrol 2-Stroke Semi-Synthetic Fuel / Oil Ratio 40:1 Carburettor Membrane Type Primer Pump Ignition CDI (capacitor dischage) Spark Plug RCJ6Y Starting Method Recoil Pull Start Fuel Tank Capacity 450ml Rated Power 0.75kW@ 7500rpm Air Speed 225km/h Measured Sound Power Level 106.2dB(A) - Page 23 Troubleshooting a non-starting engine. Problem Possible Cause Solution Electrode wet Dry electrode Covered with carbon Clean or replace spark plug Spark plug Damaged insulation Replace spark plug Spark gap incorrect Adjust to 0.6 - 0.7mm The spark plug does Electrode burnt Replace spark plug not spark Damaged HT cable...
- Page 24 Problem Possible Cause Solution Filter clogged Clean filter Tighten fuel lines to prevent air from Air is able to pass through the carburettor connection penetrating Stop the engine and let it cool down. Compression is OK Engine is overheating When you restart it, avoid long periods of heavy load and high revs Water in the fuel Drain, clean and replace fuel...
-
Page 25: Parts List
Parts list... - Page 26 Spare Part Name Spare Part Name spark plug cover screw M5*55 screw ST5*16 extinguishing line cylinder cover screw M4*20 screw M4*20 ignition starter Bakelite gasket 4*10*4 knob cylinder gasket air filter cover piston ring air filter sponge piston screw M5*55 piston pin 8*28.2 choke iron block piston circlip 8...
- Page 27 Spare Part Name Spare Part Name throttle line screw M8*1 throttle trigger left hood extinguishing switch ship type welding wire screw ST5*16 with dust cover screw ST5*14 micro switch parallel welding wire self-locking switch bushing protective switch left handle protective switch cover self-locking switch screw ST5*14 spring seat...
-
Page 28: Contact Details
Contact Details Postal Address: Genpower Ltd. Isaac Way London Road Pembroke Dock Pembrokeshire SA72 4RW Telephone: +44 (0) 1646 687880 FAX: +44 (0) 1646 686198 Technical email: aftersales@hyundaipowerproducts.co.uk Website: www.hyundaipowerproducts.co.uk Manual updates and warranty. Our manuals are constantly reviewed and updated and the latest version is posted on our website. Please contact your dealer if you’d like additional assistance. - Page 29 EC Declaration of Conformity Importer and Authorised Representative Genpower Ltd. Isaac Way, Pembroke Dock, SA72 4RW Country of Origin: China Description: Leaf Blower, Vacuum & Shredder SKU Code: HYBV 2600X Date of Issue: 22/07/2021 Regulations and Directives of Compliance • 2006/42/EC The Machine Directive •...
- Page 30 Notes...
- Page 32 Importer Genpower Ltd Isaac Way, London Road Pembroke Dock, Pembrokeshire SA72 4RW Tel: +44 (0) 1646 687880 FAX: +44 (0) 1646 686198 email: info@hyundaipowerproducts co uk www hyundaipowerproducts co uk Imported and distributed by Genpower Ltd for the United Kingdom and Ireland Licensed by Hyundai Corporation, Korea...
Need help?
Do you have a question about the HYBV2600X and is the answer not in the manual?
Questions and answers