Related Manuals for Daikin CTXS07WVJU9
Summary of Contents for Daikin CTXS07WVJU9
- Page 1 DAIKIN ROOM AIR CONDITIONER INSTALLATION MANUAL R410A Split Series MODELS CTXS07WVJU9 FTXS09WVJU9 FTXS12WVJU9...
-
Page 2: Table Of Contents
Contents Safety Considerations ........1 Refrigerant Piping Work ........10 1. Flaring the pipe end ............. 10 Accessories ............3 2. Refrigerant piping ............10 Choosing an Installation Site ......3 Installation Tips..........11 1. Indoor unit ..............3 1. Removing and installing front panel ......11 2. - Page 3 Daikin are used, fire or explosion may occur. • Do not install the air conditioner or heat pump in the • Do not use means to accelerate the defrosting process (if...
-
Page 4: Accessories
Accessories Mounting plate Mounting plate Titanium apatite deodorizing fixing screw filter M4 × 1” (M4 × 25mm) Wireless remote Remote Remote controller controller controller holder holder fixing screw M3 × 13/16” (M3 × 20mm) G Dry battery AAA. Indoor unit fixing Tube LR03 (alkaline) screw... -
Page 5: Indoor Unit Installation
Indoor Unit Installation CAUTION • Do not hit or forcefully push the INTELLIGENT EYE sensor. This can lead to damage and malfunction. • Do not place large objects near the sensor. Also keep heating units or humidifiers outside the sensor’s detection area. How to attach the indoor unit A Mounting Hook the claws of the bottom frame... -
Page 6: Installing The Mounting Plate
Indoor Unit Installation Installing the mounting plate • The mounting plate should be installed on a wall which can support the weight of the indoor unit. 1) Temporarily secure the mounting plate to the wall, make sure that the plate is completely level, and mark the drilling points on the wall. -
Page 7: Installing The Indoor Unit
Installing the indoor unit In the case of bending or curing refrigerant pipes, keep the following precautions in mind. Abnormal sound may be generated if improper work is conducted. • Do not strongly press the refrigerant pipes onto the bottom frame. •... - Page 8 Indoor Unit Installation 2) Attach the drain hose to the underside of the refrigerant pipes Remove pipe port with adhesive vinyl tape. cover here for left-side piping. Left-side piping Left-back piping Remove pipe port cover here for left-bottom piping. Left-bottom piping 3) Shape the refrigerant pipes along the pipe path marking on the mounting plate.
-
Page 9: Wiring
Wiring Refer to the installation manual for the outdoor unit also. WARNING • Do not use tapped wires, extension cords, or starburst connections, as they may cause overheating, electric shock, or fire. • Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the terminal block.) Doing so may cause electric shock or fire. -
Page 10: Drain Piping
Indoor Unit Installation Drain piping Make a downward slope 1) Connect the drain hose, as described on the right. • Avoid placing the end of the drain hose in a drainage location that Leave a gap of 1-15/16 inches (50mm) or could cause bad odors or corrosive gas to flow backward into the more at the end of the outlet outlet. -
Page 11: Refrigerant Piping Work
Refrigerant Piping Work WARNING • Do not apply mineral oil to the flare. • Prevent mineral oil from getting into the system as this would reduce the service life of the units. • Never use piping which has been used for previous installations. Only use parts which are delivered with this unit. •... -
Page 12: Installation Tips
Installation Tips Removing and installing front panel • Removal method 1) Place your fingers in the indentations on the main unit (one each on the left and right sides), and open the front panel until it stops. 2) While pushing the left side front panel shaft outward, push up the front panel and remove it. -
Page 13: How To Set The Different Addresses
How to set the different addresses When 2 indoor units are installed in one room, the 2 wireless remote controllers can be set for different addresses. 1) Remove the metal plate electrical wiring cover. (Refer to the When connecting to an HA system.) 2) Cut the address jumper (JA) on the printed circuit board. -
Page 14: Trial Operation And Testing
Trial Operation and Testing Trial operation and testing • Trial operation should be carried out in either COOL or HEAT operation. 1-1. Measure the supply voltage and make sure that it is within the specified range. 1-2. In COOL operation, select the lowest programmable temperature; in HEAT operation, select the highest programmable temperature. 1-3. - Page 15 MEMO ■ English...
- Page 16 Two-dimensional bar code is a code for manufacturing. 3P674700-1 M21B353 (2203) HT...