Table of Contents
Advertisement
Quick Links
www.xtralis.com
The Americas +1 781 740 2223 Asia +852 2916 9976 Australia and New Zealand +61 3 9936 7000
Continental Europe +41 55 285 99 99 UK and the Middle East +44 1442 242 330
The contents of this document are provided on an "as is" basis. No representation or warranty (either express or implied) is made as to
the completeness, accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or
specifications without obligation and without further notice. Except as otherwise provided, all warranties, express or implied, including
without limitation any implied warranties of merchantability and fitness for a particular purpose are expressly excluded.
This document includes registered and unregistered trademarks. All trademarks displayed are the trademarks of their respective
owners. Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/or
label.This document is subject to copyright owned by Xtralis AG ("Xtralis"). You agree not to copy, communicate to the public, adapt,
distribute, transfer, sell, modify or publish any contents of this document without the express prior written consent of Xtralis.
Doc. 14866_01
Xtralis ADPRO
®
PRO-250H
Installation Manual
October 2008
Doc. 14866_01
Advertisement
Table of Contents
Related Manuals for Xtralis ADPRO PRO-250H
Summary of Contents for Xtralis ADPRO PRO-250H
- Page 1 Your use of this document does not constitute or create a licence or any other right to use the name and/or trademark and/or label.This document is subject to copyright owned by Xtralis AG (“Xtralis”). You agree not to copy, communicate to the public, adapt, distribute, transfer, sell, modify or publish any contents of this document without the express prior written consent of Xtralis.
- Page 2 Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual Software Installation Procedure • Connect the detector to power and connect the interface module to the detector’s test socket or the terminal block, as defined in annex 1. • Connect the output of the interface module with the serial COM port of the PC.
- Page 3 Depending on the site’s animal activity, vegetation moving in the wind To the fullest extent permitted by law that any limitation or exclusion cannot apply, the total liability of Xtralis and/or other sources of disturbance, it is possible that unwanted alarms in relation to the products is limited to: occur.
- Page 4 The test socket carries V+, GND and the two RS485 ports A and B. Xtralis AG Pty Ltd reserves the right as to final determination of whether or not an equipment malfunction The detector must be opened for access to the test socket and closed again was caused by lightning or related voltage surges.
- Page 5 Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual DIP–Switches Overview Sensitivity The PRO-250H is a highly sensitive passive infrared detector designed for detection outdoors with a narrow, curtain-shaped differential field of view. PRO-250H They incorporate microprocessor-controlled signal processing, including...
- Page 6 Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual Annex 1: Electronic Board and Terminal Block Doc 14866_01...
-
Page 7: Table Of Contents
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual 21.1 Mechanical Dimensions Detector Contents Mounting and Installation..............1 Hardware / Software Mode of Operation ........1 Connecting the PRO-250H...............2 Alarm Signalling ...............2 Cover Tamper Switch...............2 Electronics Supply..............2 Anti-Tamper Output..............2 Field of View ..................2 Alignment..................3... - Page 8 Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual 20.0 Wiring the Alarm Outputs..............12 21.0 Specifications Model PRO-250H 21.0 Specifications.................13 21.1 Mechanical Dimensions Detector...........14 Optical 21.2 Mechanical Dimensions Mounting Bracket AD 653 ....14 Nominal Range 150 m (500 ft) Width @ Nominal Range 3.3 m (11 ft)
-
Page 9: Mounting And Installation
The clamp around the body of the PRO-250H should be positioned The product (eg Xtralis ADPRO AFT) should have the alarm input approximately half way between the front window and the back cover configured as Dual-End-of-Line Normally Closed. The PRO detector should to avoid slight deformations of the body near the seals at each end. -
Page 10: Connecting The Pro-250H
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual Connecting the PRO-250H 18.0 Maintenance For the definition of the connector board and terminal block refer to The detector has been designed to be virtually maintenance free but the Annex 1: Electronic Board and Terminal Block for details. -
Page 11: Alignment
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual Receiver Alignment LED Description The detection range of a PIR detector is not limited but a function of size, speed and temperature contrast of a target against its background. The •... -
Page 12: Sensitivity Settings
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual 17.0 Accessories 17.1 Interface Module IF 485B and Installation Software The installation software is very useful for alignment and signal check during setup and maintenance. It indicates the amplitudes generated by... -
Page 13: Adaptive Threshold Discrimination (Atd)
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual During the initial period of operation it is strongly recommended that walk If the mounting height is less than 2.5 m, a detection gap at approximately tests are repeated and signals monitored under various weather conditions 10 m distance may be observed for fast movements. -
Page 14: Anti Tamper Feature
Installation Manual Xtralis ADPRO PRO-250H Xtralis ADPRO PRO-250H Installation Manual Important: The transmitter CT 45-T of the cordless installation tester has to Software Mode be placed within the housing with the detector cover closed and securely Operating the detector in the SW mode, the anti tamper function is tightened.