Related Manuals for Semtech TBMS100
Summary of Contents for Semtech TBMS100
- Page 1 Motion Sensor (PIR) TBMS100-915 Reference Manual TBMS100-868 Model Name: TBMS100 DOC ver.: BQW_02_0006.002...
-
Page 2: Table Of Contents
Table of Contents 1. Description 1. Description The Motion Sensor utilizes LoRaWAN 2. Specifications connectivity to communicate the 2.1 Mechanical 2.1.1 Sensor presence or not of a person. The intended 2.2 Environmental use is to place the sensor with a good 2.3 Radio view of a room to determine if there is 2.4 Certifications and Conformity... -
Page 3: Certifications And Conformity
2. Specifications 2.1 Mechanical 2.1.1 Sensor Length x Width x Height 50mm x 20mm x 50mm without wall mount Weight 30g without battery 40g with battery Sensor • Dual Passive Infrared detectors • Fresnel Lens with 123° horizontal & 93° vertical view 2.2 Environmental 2.5 Power... -
Page 4: Operation
3. Operation 3.1 Transport Mode Sensors are shipped with a plastic battery insulating pull tab that must be removed before the operation. 3.2 Default Operation While in default operation, the device will immediately send a status change message once there is a transition from vacant to occupied state or vice-versa. Additionally, the device will send a status message every 10 minutes while in the occupied state and every 1 hour while in the vacant state. -
Page 5: Messages
4. Messages LoRaWAN Packets for this device use port 102. 4.1 Status 4.1.1 Triggers Packet Triggers: (1) While in free mode, send a message every 60 minutes; (2) When the status changes from the free mode to occupied mode, send a message immediately;... -
Page 6: Payload (Continue)
4.1.2 Payload (continue) Status Sensors status Bit [0] 1 – occupied, 0 – free Bits [7:1] Battery Battery level unsigned value ν, range 1 – 14; Bits [3:0] battery voltage in V = (25 + ν) ÷ 10. *Note: The initial operation will be in low voltage state, after 10 minutes, it will turn into a steady-state, which is referenceable. -
Page 7: Battery
5. Battery 5.1 Replacement Use ER14250 or equivalent. Remove the upper cap and replace the battery. 5.2 Cautions CAUTION: Disposal of a battery (or battery pack) into a fire or a hot oven, or mechanically crushing or cutting of a battery (or battery pack) can result in an EXPLOSION! Leaving a battery (or battery pack) in an extremely high temperature surrounding environment that can result in an EXPLOSION or leakage of... -
Page 8: Label Format Information
6. Label format information 6.1 Round label 6.1.1 All QR code URN:LWDP:58A0CB0000210000:58A0CBFFFFFEFFFF:TBMS100915:4D4483B1. The total maximum resulting character sentence is 72 alphanumeric characters long. 6.1.2 JoinEUI 900MHz: 58A0CB0000210000. (US/AU/AS923/BR) 800MHz: 58A0CB0001500000. (EU/IN/RU) Uses a hexadecimal representation resulting in 16 characters. 6.1.3 DevEUI 58A0CBFFFFFEFFFF. -
Page 9: Factory Check Code
6.1.5 Factory check code 4D4483B1. Checksum of the factory production line. 6.1.6 Model Name MODEL:TBMS100. Fixed code, not including in QR code. 6.2 PE Bag & Back Label Label Barcode PE Bag Label Back Label Definition of Back Label and PE Bag Barcode Label: GS1 DataMatrix ●... -
Page 10: Important Product & Safety Instructions
7. Important Product & Safety Instructions For the most current and more detailed information about Tabs features and settings as well as safety instructions, please download the user manual for the products online at w ww.browan.com before the use of any Tabs products or services. Certain sensors contain magnets. -
Page 11: Warnings
8. Warnings ● Do not place naked flame sources, such as ● Observe the plus (+) and minus (-) marks lighted candles, on or near the equipment. on the battery and equipment and ensure ● The battery shall not be exposed to correct use. -
Page 12: Notices
9. Notices ● Avoid exposing your sensors or batteries to ● PROP 65 WARNING: This product contains very cold or very hot temperatures. Low or chemicals known to the State of California to high temperature conditions may cause cancer and birth defects or other temporarily shorten the battery life or cause reproductive harm ●... -
Page 13: Regulatory
11. Regulatory Hereby, Browan Communications Inc. declares that the radio equipment for Tabs products is in compliance with Directive 2014/53/EU. This device complies with Part 15 of the FCC Rules and RSS Standards of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 14: Industry Canada Statement
The product complies with the US portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such a function is available. -
Page 15: Appendix. Configuration Downlink Command
Appendix. Configuration Downlink Command (Only For PIR Parameters Settings) Port Payload Length 5 bytes *Note: Configuration Down-link Command should take duty cycle into consideration. Appx. 1 Payload Bytes Field Config Command Bit [7:0] 0x01 – Set configuration, other values – RFU Config PIR Sensor Configuration Bits [4:0]... -
Page 16: Appx. 2 Configuration Command
Appx. 2 C onfiguration Command (For Sensor Settings) Port Appx. 2.1 Payload Bytes Field Config © 2019 Browan Communications Inc. All rights reserved. -
Page 17: Appx. 2.1 Payload (Continue)
Appx. 2.1 Payload (continue) Command 1 byte Bit [7:0] 0x00 – Set reporting interval in sec.(per unit:5min) default value : 3600 sec value range : 15~65535 0x02 – Set occupied interval in sec. default value : 600 sec value range : 0~65535 0x03 –... -
Page 18: Appx. 2.2 Command Description
Appx. 2.2 Command Description Payload Content Command content 00100e || 0 25802 || 0 305 || 0 40000 || 0 500148101 00 100e => reporting interval : 0x0e10 -> 3600 sec 02 5802 => Occupied override : 0x0258 -> 600 sec 03 05... -
Page 19: Appx. 4 Frame Count 0 Content
Appx. 4 Frame Count 0 Content Payload Length 17 bytes Payload Content Frame count 0 content 01 6000000 0060000 ff1f102 e 2d4f6ee 01 => command ID = > bootloader version : 0x00000006 ( 06000000 little-endian format => HW ID : 0x00000600 ( ...