Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1262-200
Summary of Contents for Benchmark 1262-200
- Page 1 DETAIL SANDER 5 Year Limited Warranty on tool READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. 3042597 JD2442U WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS 2A DETAIL SANDER Rating: 120V, 60Hz, AC Amperes: 2 Amp Speed: 13,000 OPM (no load) Sanding pad size: Detail sanding base: 5.8” x 5.8” x 3.3” (148 x 148 x 84 mm) Detail sanding attachment: 3.5” x 3.5” x 3.5” (90 x 90 x 90 mm) Finger sanding attachment: 3.6”... -
Page 3: Table Of Contents
1262-200 DETAIL SANDER TABLE OF CONTENTS Product specifications ................... 1 Table of contents ................... 2 General safety warnings ................. 3 Eye, ear & lung protection ................3 Electrical safety .................... 4 Power tool safety.................... 4 General safety rules ..................4 Work area ...................... -
Page 4: General Safety Warnings
GENERAL SAFETY WARNINGS WARNING: Before using this tool or any of its accessories, read this manual and follow all Safety Rules and Operating Instructions. The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible situations. It must be understood that common sense and caution are factors which cannot be built into the product. -
Page 5: Electrical Safety
1262-200 DETAIL SANDER GENERAL SAFETY RULES WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. WORK AREA SAFETY Keep work area clean and well lit. -
Page 6: Electrical Safety
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. -
Page 7: Specific Safety Rules
1262-200 DETAIL SANDER SPECIFIC SAFETY RULES FOR DETAIL SANDER WARNING: Know your detail sander. Do not plug in the sander until you have read and understand this Instruction Manual. Learn the tool’s applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury. -
Page 8: Extension Cord Safety
EXTENSION CORD SAFETY Make sure your extension cord is the proper size. When using an extension cord, be sure to use one heavy enough to carry the current the tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. -
Page 9: Symbols
1262-200 DETAIL SANDER SYMBOLS WARNING: Some of the following symbols may appear on the sander. Study these symbols and learn their meaning. Proper interpretation of these symbols will Three-phase alternating Volts current with neutral Amperes Direct current Hertz No load speed... -
Page 10: Know Your Detail Sander
KNOW YOUR DETAIL SANDER Palm grip Cooling vents ON/OFF switch Dust box filter vent Dust box assembly Spindle locking button Backing pad work light Cooling vents Hook & loop fastening system Finger & Delta Attachments... -
Page 11: Assembly And Operating
1262-200 DETAIL SANDER ASSEMBLY AND OPERATING INSTALLING THE DUST BOX ASSEMBLY 1. Insert the dust box assembly (1) onto the dust chute (2) (Fig. 1). 2. Push the dust box assembly fully onto the dust chute. NOTE: Remove and clean the dust box assembly periodically to remove accumulated dust from the dust box. -
Page 12: Installing Sandpaper
INSTALLING SANDPAPER WARNING: Unplug the sander from the power source before installing or changing the sandpaper. 1. Firmly press the sandpaper (1) onto the hook & loop pad (2) (Fig. 4). NOTES: Fig. 4 a) Place the sandpaper so the holes line up with the matching holes in the hook &... -
Page 13: Fitting Sanding Sheets
1262-200 DETAIL SANDER Proceed as follows to fit the required sanding plate/ attachment: Remove the fitted sanding plate by removing the mounting screw (A) using a Phillips screwdriver (not supplied). • Fit the required sanding plate/attachment to the base of the machine. -
Page 14: On/Off Switch
ON/OFF SWITCH To turn the sander ON, push the upper switch button (1) until the sander starts. To turn the sander OFF, press the lower switch button (2) (Fig. 6). SANDING Clamp or otherwise secure your workpiece to prevent it from moving under the sander while Fig. -
Page 15: Maintenance
1262-200 DETAIL SANDER MAINTENANCE GENERAL WARNING: When servicing, use only identical replacement parts. The use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. -
Page 16: Exploded View
EXPLODED VIEW... -
Page 17: Parts Listing
1262-200 DETAIL SANDER PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the sander. Any attempt to repair or replace electrical parts on this sander may create a safety hazard unless repairs are performed by a qualified technician. - Page 18 Key # Part # Part Name Quantity 4030010136 Screw ST2.9x9 3150120092 Triangle plate 4020010166 Screw M4x8 3190020062 Semicircle sponge plate 3190020063 Triangle sponge plate 3150120093 Finger plate 3190100017 Finger plate with hook and loop 3150120094 Long triangle plate 3190100018 Long triangle plate with hook and loop...
-
Page 19: Warranty
WARRANTY BENCHMARK DETAIL SANDER If this Benchmark Tool fails due to a defect in material or workmanship within 5 years from the date of purchase, return it to any Home Hardware store with the warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 20 DETAIL SANDER 5 Year Limited Warranty on tool 1262-200 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 01 / 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark READ ALL INSTRUCTIONS BEFORE FIRST USE.
Need help?
Do you have a question about the 1262-200 and is the answer not in the manual?
Questions and answers