Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1282 006
Summary of Contents for Benchmark 1282 006
- Page 1 6" ORBITAL PNEUMATIC SANDER 5 Year Limited Warranty READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS 6" ORBITAL PNEUMATIC SANDER Sanding Pad 6" (150mm) hook & loop fastening system Variable Free speed 0-12,000 OPM Average Air consumption 4.5 cfm @ 90 PSI Operating pressure 90 psi (6.3 bar) Maximum air pressure 120 psi (8.3 bar) Air inlet size 1/4”... -
Page 3: Table Of Contents
1282 006 6" ORBITAL PNEUMATIC SANDER TABLE OF CONTENTS Product Specifications ................... 1 Table of Contents ................... 2 Safety Guidelines ..................3-6 Symbols ....................... 7 Tool Specific Warnings .................. 8 ............ 9 Know Your 6" Orbital Pneumatic Sander ..............10-12 Assembly And Operating .................. -
Page 4: Safety Guidelines
SAFETY GUIDELINES WARNING: This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. DANGER! Potential hazard that will result in serious injury or loss of life. -
Page 5: Symbols
1282 006 6" ORBITAL PNEUMATIC SANDER SYMBOL MEANING • Risk of inhalation: Never directly inhale the air produced by the compressor. • Risk of bursting: Do not adjust the pressure switch or safety valve for any reason. They have been preset at the factory for this compressor’s maximum pressure Tampering with the... - Page 6 WARNING! • Do not allow unskilled or untrained individuals to operate the air tool. • Do not use the tool for any task other than that it is designed to perform. • Locate the compressor in a well-ventilated area for cooling, and a minimum of 12”...
- Page 7 1282 006 6" ORBITAL PNEUMATIC SANDER CAUTION! • Disconnect tool from the air supply and turn o the compressor before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended.
-
Page 9: Tool Specific Warnings
1282 006 6" ORBITAL PNEUMATIC SANDER TOOL SPECIFIC WARNINGS WARNING! DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to the tool safety rules. If you use this tool unsafely or incorrectly, you can su er serious personal injury. -
Page 10: Know Your 6" Orbital Pneumatic Sander
KNOW YOUR 6" ORBITAL PNEUMATIC SANDER ON/OFF trigger Hose and Dust bag port collar Adapter Compressor connection port Speed control lever Sanding pad Hose Dust bag... -
Page 11: Assembly And Operating
1282 006 6" ORBITAL PNEUMATIC SANDER ASSEMBLY AND OPERATING COMPATIBLE COMPRESSORS GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with air-powered tools. The compressor should be able to supply a minimal air delivery of 4.56 CFM @ 90 PSI to ensure the compressor can run continuously with the tool. - Page 12 If a filter/regulator/lubricator is not installed on the air system, air operated tools should be lubricated at with each use or after 2 hours work with 2 to 6 drops of oil, depending on the work environment, directly through the male fitting in the tool housing.
- Page 13 1282 006 6" ORBITAL PNEUMATIC SANDER INSTALLING DUST HOSE AND DUST BAG (FIG.2). Tie the dust bag to one end of the dust hose and then insert the other end of the hose into the hose and dust bag port collar at the back of the sander. Turn the collar clock-wise to lock hose into the tool.
-
Page 14: Maintenance
MAINTENANCE NOTE: Do not store the tool anywhere temperatures will fall below freezing. WARNING: Disconnect tool from air supply before maintenance/service, adjusting, cleaning jams, reloading and when not in use. Repairs must be performed by a qualified service technician only. Failure to comply will lead to serious injury or loss of life. Lubricate the air sander daily with a few drops of air tool oil dripped into the air inlet •... - Page 15 1282 006 6" ORBITAL PNEUMATIC SANDER PROBLEM POSSIBLE CAUSES REMEDIES Tool runs at normal 1. Motor parts worn. 1. Lubricating clutch housing. speed but loses 2. Cam clutch worn or sticking 2. Check for excess clutch oil. Clutch cases under load due to lack of lubricant.
-
Page 16: Exploded View
EXPLODED VIEW... -
Page 17: Parts List
1282 006 6" ORBITAL PNEUMATIC SANDER PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a qualified technician. - Page 18 Key # Part # Part Name Quantity 03.02.02.055.007 Switch plug 03.02.02.055.010 Switch pin 03.02.02.055.009 Switch spring 03.05.01.043 O-ring 11.5x1.8 03.02.02.055.008-01 Air inlet 03.05.01.197 O-ring 4.2x1 03.02.02.055.006 Switch pole 03.05.01.284 O-ring 8.5x1.5 03.02.02.055.011 Adjust knob 03.02.02.055.021 Retainer ring 12...
-
Page 19: Warranty
WARRANTY BENCHMARK WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 20 6" ORBITAL PNEUMATIC SANDER *5 year limited warranty on tool 1282 006 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the 1282 006 and is the answer not in the manual?
Questions and answers