Technical Data; Assembly And Starting; Before Starting The Equipment - EINHELL TC-AC 400/50/8 Original Operating Instructions

4. Technical data

Mains connection: .......................... 230 V ~ 50 Hz
Motor rating: ................................2200 W S3 50%
Speed (motor) min : .................................... 2850
-1
Speed (pump) min : .................................... 2850
-1
Operating pressure bar: ............................. max. 8
Pressure vessel capacity (in liters): ................. 50
Theoretical suction rate l/min ........................ 400
Output (compressed air) at 7 bar: . . 176 liters/min
Output (compressed air) at 4 bar: ... 207 liters/min
Sound power level L
WA
K uncertainty: .......................................... 1.7 dB
WA
Sound pressure level L
K uncertainty: .......................................... 1.7 dB
pA
Protection type: ............................................. IP20
Weight of the unit in kg: .................. approx. 40 kg
Oil quantity: ................................ approx. 0.3 liters
Operating mode S3 - 50% - 10min: S3 = Inter-
mittent mode without infl uencing the starting pro-
cess. This means that during a period of 10 min
the max. operating time is 50% (5 min).
Noise
The noise emission values were measured in ac-
cordance with EN ISO 2151.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
•
Examine the machine for signs of transit da-
mage. Report any damage immediately to the
company which delivered the compressor.
•
The compressor should be set up near the
working consumer.
•
Avoid long air lines and long supply lines (ex-
tensions).
•
Make sure the intake air is dry and dust-free.
•
Do not set up the compressor in damp or wet
rooms.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5°C to +40°C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
Anl_TC_AC_400_50_8_SPK1.indb 18 Anl_TC_AC_400_50_8_SPK1.indb 18
in dB: ............................ 97
in dB: ....................... 72
pA
- 18 -
GB
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
The oil level in the compressor pump has to
be checked before putting the equipment into
operation.
•
The equipment must be set up where it can
stand securely.
•
Use flexible hoses in order to prevent trans-
mitting unacceptable loads to the pipeline
system at the connection between the com-
pressor system and the pipeline system.
•
It is essential to use separators, traps and
drains which process the liquids produced by
the compressor before the compressor sys-
tem is put into operation.
•
Supply hoses at pressures above 7 bar
should be equipped with a safety cable (e.g.
a wire rope).

6. Assembly and starting

Important!
You must fully assemble the appliance before
using it for the fi rst time.
6.1 Fitting the wheels (3)
Fit the supplied wheels as shown in Fig. 6.
6.2 Fitting the supporting feet (4)
Fit the supplied supporting feet (4) as shown in
Fig. 7.
6.3. Replacing the oil sealing plug (14)
Remove the transportation cover from the oil fi ller
opening with a screwdriver and insert the sup-
plied oil sealing plug (14) into the oil fi ller opening
(Fig. 9).
6.4 Fitting the air fi lter (1)
Use a screwdriver to remove the transportation
cover from the air fi lter connection.
Screw in the supplied air fi lter (Fig. 10).
6.5. Power supply
•
The motor is fitted with an overload switch
(Fig. 3/Item 16). If the compressor overloads,
the overload switch switches off the equip-
ment automatically to protect the compressor
from overheating. If the overload switch trig-
gers, switch off the compressor using the ON/
OFF switch (8) and wait until the compressor
cools down. Then press the overload switch
21.10.15 08:37 21.10.15 08:37