Related Manuals for ViewZ VZ-WM50
Summary of Contents for ViewZ VZ-WM50
- Page 1 VZ-WM50 WALL MOUNT FOR 27" to 32" VZ-WM50 INSTALLATION INSTRUCTIONS VESA COMPATIBLE 400 x 400, 400 x 300, 55" MAX 300 x 300, 300 x 200, 200 x 200, 200 x 100, 100 x 100, 100 x 75, MAX WEIGHT 115 lbs / 52 kg 75 x 75 mm www.ViewZUSA.com | 1-714-996-1177...
-
Page 2: Weight Limit
WEIGHT OF THE FLAT-PANEL. IF NOT, THE WALL STRUCTURE MUST BE REINFORCED. Parts Your ViewZ mount product is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399. Wall Plate... - Page 3 Before starting assembly, verify all parts are included and undamaged. If any part is missing or damaged, please contact: rma@viewzusa. com or 714-996-1177. Note - Not all parts and hardware (included) will be used. Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com...
-
Page 4: Installation Tools
Step 2 When attaching brackets to the flat screen, be careful about over-tightening screws and be sure about breaking bottom out of the mounting holes. Visit the ViewZ USA website at http://www.viewzusa.com Installation Instructions... - Page 5 A. Flat Back B. Round Back / Extra Space Mounting Safety Two people are recommended to install the mount. Ensure monitor bracket is securely fastened before moving onto the next step. Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 6 • All lag bolts (F) must be firmly tightened to prevent unwanted movement of the wall palte (1). • Ensure the wall plate is securely fastened to the wall before continuing to the next step. 2A-1 2A-2 2.75” 70mm Drill pilot holes. Visit the ViewZ USA website at http://www.viewzusa.com Installation Instructions...
- Page 7 Wall anchor is necessary Install wall plate (1) using lag bolts (F) and washer (J) and anchor (O). Tighten the lag bolts (F) until they are pulled firmly against the wall palte (1). Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 8 2B-2 • Position the wall plate at your desired height and line-up the holes with your stud center line. • Level the wall plate and mark the holes Visit the ViewZ USA website at http://www.viewzusa.com Installation Instructions...
- Page 9 Be sure to drill into the center of the stud. 2B-4 • Install the wall plate assembly using lag bolts (F) and washer (J). • Tighten the lag bolts (F) only until it against the wall plate. Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 10 WM series Installation - Tighten Step 5 Please adjust the tilting angle with the Allen wrench for both (2) and (3) as the pictures show before hanging monitor. Visit the ViewZ USA website at http://www.viewzusa.com Installation Instructions...
- Page 11 • Pull the strap down and push the monitor to secure the monitor brackets (2) and (3) to the wall plate (1). • If cannot tilt the monitor, please take the monitor off and then adjust the tilt as STEP 5 shows. Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 12 Disclaimer ViewZ USA intends to make this manual accurate and complete. However, ViewZ USA makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Need help?
Do you have a question about the VZ-WM50 and is the answer not in the manual?
Questions and answers