Advertisement
Quick Links
Advertisement
Related Manuals for ViewZ VZ-WM11
Summary of Contents for ViewZ VZ-WM11
- Page 1 VZ-WM11 ViewZ Wall Mount Instruction Manual For 10 ~ 24" ViewZ Monitors...
-
Page 2: Installation Tools
STRUCTURE MUST BE REINFORCED. Wall Mount Assembly Components Your ViewZ mount product is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399. One-Latch Mounting Base (Qty 1) - Page 3 WM series Features Swivel You can adjust mount angle between -45⁰ and 45⁰. 1.97”/ 50 mm 2.95”/ 75 mm 3.94”/100 mm VESA Tilt You can adjust mount angle between -30⁰ and 30⁰. Installation Instruction Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 4 This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! Visit the ViewZ USA website at http://www.viewzusa.com Installation Instruction...
- Page 5 When you tight the screw, the screw should be properly installed. If the screw is too big or small, it cause the serious damage to the monitor or person. 2) Install the monitor plate with the given screw & washer M4 Screw M6 Screw M4 Washer M6 Washer Monitor Plate Installation Instruction Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 6 Drywall covering the wall, should not be exceeded over 5/8 inch (16 mm). Minimum wood stud size : common 2 x 4 inch (51x102 mm), nominal 1½ x 3½ inch (38x39 mm) Stud center should be verified Visit the ViewZ USA website at http://www.viewzusa.com Installation Instruction...
- Page 7 Pilot holes should be drilled to a depth of 2.16 inch (55 mm). Be sure to drill into the center of the studs. Improper usage could redue the holding power of the lag bolt and it cause serious damage to the stud, monitor or person. Do not over-tighten the lag bolts. Installation Instruction Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 8 Mount the wall plate assembly directly onto the concrete surface. Minimum solid concrete thickness - 8 inch (203 mm). Pilot holes should be drilled to a depth of 2.16 inch (55 mm). Visit the ViewZ USA website at http://www.viewzusa.com Installation Instruction...
- Page 9 Be sure the anchors are seated flush with the concrete surface. Improper usage could redue the holding power of the lag bolt and it cause serious damage to the concrete, monitor or person. Do not over-tighten the lag bolts. Installation Instruction Visit the ViewZ USA website at http://www.viewzusa.com...
- Page 10 Step 4 - Wall Plate Installation Integrity Test 1) Before hanging the monitor, please try to pull the mount to make sure that it has been assembled on the wall tightly. 22 lbs (10 kg) Visit the ViewZ USA website at http://www.viewzusa.com Installation Instruction...
- Page 11 Step 5 - Install and Secure the Monitor to the Wall Plate 1) Hang the monitor/monitor plate assembly onto the wall palte and tighten the screw which you took out. Mounting Safety HEAVY! You may need an assistance at this step. Installation Instruction Visit the ViewZ USA website at http://www.viewzusa.com...
-
Page 12: Warranty
What ViewZ USA Will Do At the sole option of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defective. If ViewZ USA chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs.
Need help?
Do you have a question about the VZ-WM11 and is the answer not in the manual?
Questions and answers