Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ViewZ VZ-WM60
Summary of Contents for ViewZ VZ-WM60
- Page 1 INSTALLATION INSTRUCTIONS VZ-WM60 Universal Low Profile Flat Mount for 40” to 55” ViewZ Monitors NORTH AMERICA 177 W. Orangethorpe Ave. Placentia, CA 92870 USA USA and Canada Phone: 1-888-99-ViewZ Other Locations Phone: (001) 714-996-1177 Fax: (001) 714-996-1138 853177002847...
-
Page 2: Table Of Contents
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact. Contact ViewZ with any questions: (888) 99-ViewZ techsupport@viewzusa.com Page 2 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 3: Installation Tools
Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact ViewZ (888) 99-ViewZ. Wall Plate (Qty 1) -
Page 4: Mounting Hardware
M6 x 16mm (Qty 6) M8 x 25mm (Qty 6) M8 x 16mm (Qty 6) If your unit requires alternative mounting hardware, use commercially available hardware or contact ViewZ (888) 99-ViewZ. Page 4 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 5: Features
Mounting Slots - Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel. Safety Bar - Prevents the flat panel from detaching. Installation Instructions Page 5 Visit the ViewZ website at http://www.viewzusa.com... -
Page 6: Wood Stud Installation
Only use 1/4” drill bit when drilling the pilot holes. Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. Page 6 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 7: Concrete Surface Installation
Step 5. Use a hammer to lightly tap each anchor into Step 2. Mark off four holes to be used for securing the place so that they are flush with the wall. mount and place the wall plate aside. Installation Instructions Page 7 Visit the ViewZ website at http://www.viewzusa.com... - Page 8 Using the universal spacers Thread Depth will change the overall length of the Indicator hardware used. Figure 1 Screw Screw Marking Marking Thread Depth Thread Depth Indicator Indicator Figure 3 Figure 2 Page 8 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com...
-
Page 9: Universal Spacer Installation
Pre-install the mounting screws, spacers and washers. Once mounted, push down to eliminate movement from the bracket. Then proceed to tighten the rest of the hardware. Repeat this process for the installation of the remaining mounting bracket. Phillips Head Screwdriver M5, M6 Installation Instructions Page 9 Visit the ViewZ website at http://www.viewzusa.com... -
Page 10: Mounting Bracket Installation
Step 6. Attach each bracket to the flat panel by aligning the holes on each bracket with the threaded inserts on the back of your flat panel. Secure the bracket to the flat panel by inserting a minimum of two (2) screws per bracket. Do not overtighten the screws. Page 10 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 11: Fixed Tilt Bracket Installation (Optional)
Step 1. Raise the flat panel (two people required) past the top and bottom mounting rails and slide the flat panel down slowly, keeping it close to the wall, and engage the mounting brackets to the rails of the wall plate. Installation Instructions Page 11 Visit the ViewZ website at http://www.viewzusa.com... -
Page 12: Technical Specifications
Mounting Bracket Security Bar Step 1. Slide the security bar between the lower mounting rail and the bottom of the wall plate. Technical Specifications All measurements are in inches [mm]. Page 12 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 13: Warranty
At the sole option of ViewZ, ViewZ will repair or replace any product or product part that is defective. If ViewZ chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs.
Need help?
Do you have a question about the VZ-WM60 and is the answer not in the manual?
Questions and answers