Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for AOpen 16PM1Q
Summary of Contents for AOpen 16PM1Q
- Page 1 AOPEN LCD Monitor 16PM1Q User's Guide...
- Page 2 A OPEN Incorporated. AOPEN LCD Monitor User's Guide Model number: __________________________________ Serial number: ___________________________________ Date of purchase: _________________________________ Place of purchase: ________________________________ AOPEN and the AOPEN logo are registered trademarks of AOPEN Incorporated. Other companies' their respective companies.
-
Page 3: Special Notes On Lcd Monitors
Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. •... -
Page 4: Safe Listening
Safe listening To protect your hearing, follow these instructions. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion. • After setting the volume level, do not increase it after your ears have adjusted. •... -
Page 5: Product Servicing
Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to quali ed service personnel. Unplug this product from the wall outlet and refer servicing to quali ed service personnel when: •... -
Page 6: Lcd Pixel Statement
Abandonment Guidance Notes This symbol on the product or its packaging indicates that the product must not be disposed of with other household waste and that you are instead responsible for taking your used equipment to a designated collection point for used electrical and electronic equipment. -
Page 7: Tips And Information For Comfortable Use
Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury. - Page 8 • using a glare-reduction lter • using a display visor, such as a piece of cardboard extended from the display's top front edge • Avoid adjusting your display to an awkward viewing angle. • Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: •...
- Page 9 16PM1Q xxxxxx; (“x” = 0~9, a ~ z, A ~ Z, or blank) We, AOPEN Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following...
- Page 10 The following local Manufacturer /Importer is responsible for this declaration: Product: LCD Monitor Model Number: 16PM1Q SKU Number: 16PM1Q xxxxxx; (“x” = 0~9, a ~ z, A ~ Z or Blank) Name of Responsible Party: AOPEN America Corporation Address of Responsible Party: 333 West San Carlos St. Suite 1500 San Jose, CA 95110 U.
- Page 11 Special notes on LCD monitors Information for your safety and comfort Safety instructions Cleaning your monitor Connecting/disconnecting the device Accessibility Safe listening Warnings Using electrical power Product servicing Additional safety information IT Equipment Recycling Information Disposal instructions LCD pixel statement Tips and information for comfortable use CE Declaration of Conformity Federal Communications Commission...
- Page 12 Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor Quick start guide PM1 Series 16PM1Q User Manual PD charger Type-C power cable (1.5m) Type-C date cable (1m)
-
Page 13: Attaching The Monitor To The Base
Attaching the monitor to the base 1. Remove the monitor leather case from the packaging and place it on a stable and level workspace. 2. Open leather case. The viewing angle of the monitor can be adjusted using the leather case. (As shown below) -
Page 14: Power Saving
Power saving The monitor will be switched to "power saving" mode by the control signal from the display controller, as indicated b power LED. Model LED light Blue Power saving None The power saving mode will be kept until a control signal has been detected or the keyboard or mouse is activated. -
Page 15: Connector Pin Assignment
Connector pin assignment Type C (24Pin female connector) TX1+ TX2+ TX1- TX2- VBUS VBUS CONN SBU1 DBU2 VBUS VBUS RX-2 RX-1 RX2+ RX+1... -
Page 16: Standard Timing Table
Standard timing table Mode Resolution 640×480 VESA 800×600 VESA 1024×768 VESA 1280×1024 VESA 1280×720 WXGA+ 1440×900 WXGA+ 1600×900 WSXGA+ 1680×1050 UXGA 1920×1080... -
Page 17: Installation
Installation To install the monitor on your host system, please follow the steps below: Steps Connect the monitor to your computer 1. Connect the signal transmission cable (Thunderbolt 3 (USB-C) cable) to the monitor’s Type-C jack and the Type-C output jack of the computer’s display card. 2. -
Page 18: User Controls
User controls SOURCE (EXIT) / Power Switch: To turn the monitor ON or OFF. Lights up to indicate the power is turned ON. Using the Shortcut Menu External controls Brightness a. Press this button to adjust the brightness diretly. Press this button to select the desired item when in OSD menu. -
Page 19: Adjusting The Osd Settings
Adjusting the OSD settings Note: The following content is for general reference only. Actual produc ations may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD setting and general settings. For advanced settings, please refer to following page: Adjusting the Brightness setting 1. - Page 20 Adjusting the Image setting 1. Press the MENU key to bring up the OSD. 2. Using the + - / keys, select Color from the OSD. Then navigate to the feature you wish to adjust. Press the MENU key to c rm your select.
- Page 21 Product the OSD setting 1. Press the MENU key to bring up the OSD. 2. Using the + - / keys, select OSD Settings from the OSD. Then navigate to the feature you wish to adjust. 3. Press the MENU key to c rm your select.
- Page 22 Product the Music setting DDC/CI 1. Press the MENU key to bring up the OSD. 2. Using the + - / keys, select OSD Settings from the OSD. Then navigate to the feature you wish to adjust. 3. Press the MENU key to c rm your select.
-
Page 23: Troubleshooting
Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or swit tor. Note: AOPEN monitor is purposed for video and visual display of information obtained from electronic devices.