Page 1
SHENZHEN CRYSTAL VIDEO TECHNOLOGY CO.,LTD USER MANUAL ADD: Unit 05-06, Floor 24, Changhong Science & Technology Mansion, Keji 12th Road South, High-tech Industrial Park, Nanshan District, Shenzhen, P.R. China This user manual applies to Aurora: Post code:518057 www.cv-hd.com Transmitter: 7120 Tel: +86-755-29977913 E-mail: Sales@cv-hd.com...
Page 2
Warning Important Information Please read this user manual carefully before using this product. In accordance with the safety This product should not be exposed to dripping or splashing. Please keep any liquid thing off the product. precautions and operating instructions listed on this user manual, please use the product in a correct way.
Cautions Contents Thank you for choosing CVW professional wireless video transmission system. Cautions Before using this product, please read carefully the following cautions: About the User Manual * Avoid prolonged exposure to the direct sunlight or use this product in dusty environments. Product Overview * Be sure to use the product within the temperature and humidity range.
In the point-to-point mode, the video output is from HDMI or SDI. In the RTSP streaming mode, the video streaming port is the LAN port (RJ45), and can output Aurora is a set of broadcast-grade 4K UHD wireless video transmission system, video simultaneously with the HDMI or SDI port.
Packing List RS232/RS422 transparent transmission Please check the following items carefully after unpacking. If any of them is missing, The product supports RS232/422 transparent transmission that enables the please contact your seller. device connected to the receiver to send control commands to the camera side. Support intercom and Tally The product supports voice intercom and Tally function.
Transmitter ports introduction: Ports and Buttons TX: 7120 Item Description Antenna Connectors Tally Output RS-232/422 LAN Port Power Button DOWN Button MENU Button UP Button Headset Jack HDMI Input 12G-SDI Input 12G-SDI Loop Output Power Input...
Receiver ports introduction: RX: 3120 Item Description Antenna Connectors Tally Input RS-232/422 LAN Port Power Button LEFT Button DOWN Button RIGHT Button UP Button MENU Button Headset Jack HDMI Output 12G-SDI Output Power Input...
OLED Display RX:3120 TX:7120 13.9V No Video 13.9V 4K 60P CH 4 HDMI 60M CH 1 Item Icon Content Status Battery voltage Current battery voltage 13.9V Item Icon Content Status Blank Fan status Battery voltage Current battery voltage 13.9V No signal strength indication No connection Blank Signal strength...
RX:3120 Buttons Operation TX:7120 Function Operation Description Press the LEFT or RIGHT button to cycle switch between Operation Description Function In the main menu, the LEFT button is used to channels, then press the MENU button to confirm the Channel change to a higher channel, the RIGHT button change.
Product Installation Installation of Transmitter 1. Install the antennas to the antenna connectors , and arrange them to be fan-shaped.(As shown in the figure below) Lithium Battery 3. Please connect the transmitter properly to the camera using a HDMI/SDI cable. (Please note that “HDMI”...
Installation of Receiver 2. Please place the receiver at a 1. Install the antennas to the antenna connectors, and arrange them to be height of around 1.5 to 2 meters fan-shaped. (As shown in the figure below) above the ground. The receiver can be installed through the 3/8"...
Tally 4. The receiver can be powered by the battery mounted on the V-mount plate, Tally or connected to the XLR port via a power adapter. If both are connected , First, plug the Tally indicator into the transmitter’s Tally output , and connect the the battery will be used in priority, and will automatically switch to the power switch console to the receiver’s Tally input.
Page 13
RS232/RS422 transparent transmission Please select “Video-RTSP”from the sub-menu to enable the RTSP function. RS232&422 port is RJ45 connector, baud rate can be modified through After the setting is completed, please connect the LAN port of the transmitter the display menu UART-Baudrate. The pinout is shown as below: or receiver to a PC or other device.
Troubleshooting 7) Never power up the product without the original antennas and power adapter. 1) HDMI input matches HDMI/SDI output; SDI input matches HDMI/SDI output. 8) During use, the surrounding environment might affect wireless transmission quality. The SDI and HDMI output cannot be supported simultaneously by the receiver. These situations are below: The corresponding input and output operations can be selected based on the display instructions.
Need help?
Do you have a question about the Aurora and is the answer not in the manual?
Questions and answers