Related Manuals for Horizon Fitness ANDES E
Summary of Contents for Horizon Fitness ANDES E
- Page 1 ELLIPTICAL OWNER’S MANUAL Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.
- Page 2 ASSEMBLY ENGLISH WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises.
-
Page 3: Tools Included
READING RACK PRE ASSEMBLY TOOLS INCLUDED: CONSOLE F 5 mm L-Wrench UNPACKING TOUCH PAD PANEL AND DISPLAY WINDOWS F 8 mm L-Wrench UPPER HANDLE BAR Unpack the product where you will be using it. Place the elliptical carton on a level F 10/13 mm Flat Wrench flat surface. -
Page 4: Assembly Step
ASSEMBLY STEP 1 ASSEMBLY STEP 2 HARDWARE BAG 1 CONTENTS: HARDWARE BAG 2 CONTENTS: NOTE: Be careful not to pinch any wires while Bolt Spring washer Flat washer Wave washer Bolt Spring washer Flat washer attaching the Φ8.2 Φ8.2 Φ17.2 Φ10.2 Φ10.2 console mast. - Page 5 ASSEMBLY STEP 3 ASSEMBLY STEP 4 HARDWARE BAG 3 CONTENTS: HARDWARE BAG 4 CONTENTS: Bolt Spring washer Flat washer Bolt Spring washer Flat washer Φ8.2 Φ8.2 Φ8.2 Φ8.5 Qty:2 Qty:2 Qty:2 Qty:2 Qty:2 Qty:4 Flat washer Wave washer LOWER LINK ARM Flat washer Rubber washer Φ20.2...
- Page 6 ASSEMBLY STEP 5 ASSEMBLY STEP 6 HARDWARE BAG 5 CONTENTS: HARDWARE BAG 6 CONTENTS: Bolt Spring washer Button head bolt Button head bolt Φ8.2 Qty:2 Qty:2 Qty:4 Qty:3 TOP CAP CONSOLE Open HARDWARE BAG 6. Flat washer Nylon nut Φ8.2 Qty:2 Qty:2 Attach the CONSOLE CABLES to the CONSOLE.
-
Page 7: Elliptical Operation
ELLIPTICAL OPERATION This section explains how to use your elliptical’s console and programming. The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following: • LOCATION OF THE ELLIPTICAL • POWER/GROUNDING INSRUCTIONS ASSEMBLY COMPLETE! • FOOT POSITIONING • MOVING THE ELLIPTICAL •... -
Page 8: Console Operation
CONSOLE OPERATION Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) LED DISPLAY WINDOWS: time, distance, calories, heart rate, RPM and resistance level. B) LED DISPLAY INDICATORS: indicates what information is being displayed. C) START: press to begin exercising, start your workout, or resume exercising after pause. -
Page 9: Program Information
PROGRAM INFORMATION P1) MANUAL: Adjust your resistance manually during your workout. P2) TARGET 1 – DISTANCE: Push yourself and go further during your workout with 13 distance workouts. Choose from 1 mile, 2 miles, 5k, 5 miles, 10k, 8 miles, 15k, 10 miles, 20k, half marathon, 15 miles, 20 miles, and marathon KCAL goals. -
Page 10: Getting Started
GETTING STARTED TO RESET THE CONSOLE Hold STOP for 3 seconds. Check to make sure no objects are nearby that will hinder the movement of the elliptical. FINISHING YOUR WORKOUT Plug in the power cord and turn the elliptical ON. (Switch is located at the bottom-front of the When your workout is complete, the unit will beep. - Page 11 Horizon EX59 / ANDES E | Rev. 1.0 E ©2021 Horizon Fitness...