Advertisement
Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your DUAL amplifier is installed by a professional installer or an authorized dealer.
Before You Start
Mounting Location
Note: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only.
Power Wire (BAT+)
Ground Wire (GND)
The amplifier ground wire should be as short as possible. Choose a clean unpainted section of metal or the vehicle chassis when attaching the ground connection. Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
The remote turn-on wire connects to the head unit's amplifier turn-on lead or power antenna output.
Speaker Wires
Input Signal
Main Power Connections
Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle's electrical system.
Fuse Rating
When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the amplifier.
XPR522 30 amp ATO x 1
XPR540 25 amp ATO x 2
Power/Ground Wire Size
For optimum performance, use only the wire size listed below or larger. Make sure to use the same size power and ground wire.
XPR522 10 awg
XPR540 8 awg
Speaker Connections
Connect speaker wires observing polarity. The minimum impedance load for the XPR522 or XPR540 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XPR522 and XPR540 can be wired for stereo, bridged or stereo/ bridged simultaneous operation.
Input Signal Connections
Low Level Input (RCA)
Low level (RCA) input signal is preferred for best performance. Typical trunk-mount amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will minimize noise.
High Level Input (Speaker Wire)
High level inputs should only be used when RCA outputs are not available from the head unit. Connect the head unit speaker outputs to the high level input connector as shown below. The black wire (signal reference ground) may or may not require a connection to chassis ground - depending on your particular installation.
Do not use both low and high level inputs at the same time - connect only one or the other.
Input level Control | The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input.
|
Input Mode Switch (XPR540) | Select 2 CH mode if the head unit only has 1 pair of RCA outputs. Plug the RCA's from the head unit into either the front or rear channel. All 4 amplifier inputs will receive a signal. Note: There is no fader function when using 2 CH mode. Select 4 CH mode if the head unit has 2 pairs of RCA outputs. Plug the RCA's from the head unit into either the front or rear channel. |
Crossover Mode | The crossover is used to filter out frequencies above or below a certain point. Choose LPF when using the amplifier with subwoofers, HPF when using with midrange/tweeter combinations and OFF when using with coaxial-type speakers. Note: Choose OFF when using the amplifier in stereo/ bridged simultaneous mode. In this mode, passive crossovers are required. Failure to use the correct passive components may damage the amplifier and/or speakers. Consult a qualified professional for recommendations. |
Crossover Frequency Control | This control allows precise adjustment of the crossover frequency. |
Bass Boost | This control provides additional boost @ 45Hz when used with subwoofers. Adjust this control with caution - as improper use can damage speakers! |
LED Indicator | The LED indicator illuminates blue during normal operation (POWER) and red when the amplifier detects a fault (PROTECT). |
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.dualav. com.
What to do?
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company's negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.
XPR522
Power Output:
150 Watts x 2 channels @ 4 ohms
300 Watts x 2 channels @ 2 ohms
600 Watts x 1 channel @ 4 ohms (bridged)
Peak Music Power Output: 600 Watts @ 4 ohms
Signal to noise ratio: 75dBA (reference: 1 watt into 4 ohms)
Frequency response: 20Hz ~ 20kHz
Amplifier dimensions: 2.76" x 9.09" x 10.55"
Typical installation dimensions: 3.75" (D) x 10.25" (W) x 11.50" (H)
XPR540
Power Output:
150 Watts x 4 channels @ 4 ohms
300 Watts x 4 channels @ 2 ohms
600 Watts x 2 channels @ 4 ohms (bridged)
Peak Music Power Output: 1200 Watts @ 4 ohms
Signal to noise ratio: 75dBA (reference: 1 watt into 4 ohms)
Frequency response: 20Hz ~ 20kHz
Amplifier dimensions: 2.76" x 13.82" x 10.55"
Typical installation dimensions: 3.75" (D) x 15" (W) x 11.50" (H)
Problem | Cause | Action |
Unit will not turn on (no power LED indicator) | +12V wire not connected or incorrect voltage REM wire not connected or incorrect voltage | Check connections for proper voltage (11~16VDC) |
GND wire not connected | Check connection to ground | |
Fuse(s) blown | Replace fuse(s) | |
Unit has power - LED is blue (but no sound) | Speaker wires not connected | Check connections at speakers |
Volume turned all the way down | Increase volume level at head unit | |
One or more speaker wires touching each other or touching chassis ground | Insulate all bare speaker wires from each other and chassis ground | |
Speaker(s) defective or damaged | Check/replace speaker(s) | |
Input signal not connected | Check high or low level inputs for proper connection | |
Unit blows fuse(s) | Incorrect fuse rating | Use fuse(s) with correct rating |
+12V wire touching chassis ground | Check for pinched wire | |
Speaker(s) defective or damaged | Check/replace speaker(s) | |
Engine noise | Bad ground connection | Make sure amplifier is grounded to clean bare metal |
Signal ground loop or RFI (radio frequency interference) | Re-route RCA cables from existing high current wiring | |
LED illuminates red (protect mode) | One or more speaker wires touching each other or touching chassis ground | Insulate all bare speaker wires from each other and chassis ground |
Speaker(s) defective or damaged internally (shorted) | Check/replace speaker(s) | |
Speaker load less than 2 ohms (stereo) Speaker load less than 4 ohms (bridged) | Adjust speaker load - amplifier will not operate at less than 4 ohms when bridged | |
Distorted audio output | Incorrect input signal type or input level too high | Check connections and reduce/adjust input level |
Low audio output | Incorrect input signal type or input level too low | Check connections and increase/adjust input level |
Weak bass | Speaker(s) are wired out of phase | Check (+) and (-) speaker connections (Observe correct polarity) |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Dual XPR522, XPR540 - Mobile Power Amplifiers XPR Series Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the XPR522 that isn't answered in the manual? Leave your question here.