Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vanderbilt ARS6311-RX
Summary of Contents for Vanderbilt ARS6311-RX
- Page 1 Card reader ARS6311-RX Configuration Manual Vanderbilt International (IRL) Ltd.
- Page 2 Data and design subject to change without notice. / Supply subject to availability. © 2016 Copyright by Vanderbilt International (IRL) Ltd. Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger erkennt diese Rechte an und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder...
-
Page 3: Table Of Contents
Programming Examples ..............26 Appendix ....................27 Dimensions ..................27 Various example Connections ............28 7.2.1 Reader in Stand-alone Mode - I/O Board .......... 28 Maintenance ..................29 Disposal ..................... 29 List of Users ..................30 Vanderbilt International (IRL) Ltd. 05.2016... - Page 4 Vanderbilt International (IRL) Ltd. 05.2016...
-
Page 5: Safety Regulations And Warnings
Approval If used according to the instructions, this radio system meets the basic require- ments of article 3 and the remaining applicable conditions of the R&TTE directive 99/4/EC. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 6: Technical Specifications
UNIQUE EM 125 kHz – (EM4100/4102 compatible) CerPass / SiPass – Miro – Communication distance Max. 150 m, between ARS6311-RX and ACS6311 Temperature range -25 °C to +60 °C Relative humidity 10 to 95% (non-condensing) Ingress protection IP 65 Dimensions... -
Page 7: General
(i.e. the door lock relay). NOTE When configured for Stand-alone Mode, an ARS6311-RX may be used in pair with another ARS se- ries reader. In this setup both reader can provide two-way door control (entry and exit). -
Page 8: Features
Built-in signals to ACS6311 I/O Board. ONLINE Operation – Reader The factory new ARS6311-RX unit is pre-configured for ONLINE operation mode with a Magstripe data format interface. For the ONLINE operation no further pro- gramming is required. Please refer to chapter 5 for installation and to chapter 6.1, if a change of the communication interface is needed. -
Page 9: Stand-Alone Operation
4.4.1 Users In Stand-alone Mode, the ARS6311-RX can register up to 120 users with cards and ID numbers (000–119). The ARS6311-RX precludes assignment of the same card to more than one user. User identification is done by verifying the card pre- sented by a user. -
Page 10: Armed And Disarmed Mode
General 4.4.2 ARMED and DISARMED Mode When in Stand-alone Mode the ARS6311-RX can be in any of the two operational modes available, either ARMED or DISARMED State. Its current mode is indicated by the reader’s dual color LED STATUS , which lights in red for ARMED or green for DISARMED State. -
Page 11: Unlocking A Door
In the last case the Toggle or Toggle LTD User can read its card in order to switch the reader from ARMED to DISARMED Mode, thus re-enabling the reader to grant access to other users. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 12: Alarms
4.4.5 Alarms The ARS6311-RX has been designed to detect and indicate the following alarm types: Forced Door, Pre-alarm and Door Ajar (Door Held). The alarm signaling is carried out over the dedicated Alarm Output Line and optionally on the Internal Buzzer (check the Door Alarm Indication on Internal Buzzer option in the config- uration code in installer programming table, please refer to chapter 6.3 Installer... -
Page 13: Acoustic And Optical Signals
Steady is corrupted or a Master/Installer Card is not pro- grammed). NOTE When the ARS6311-RX operates with a second ARS6311-RX (for two-way control of the door) the LED indications on the second reader are synchronized. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 14: Installation
Installation Installation The ARS6311-RX reader should be mounted near the supervised door on a verti- cal piece of supporting structure. If you also use the ACS6311, this part has to be mounted in the secure area. Disconnect power supply before making any electrical connections. -
Page 15: Opening The Housing
Installation Opening the housing Fig. 1 Opening the housing Mounting Fig. 2 Mounting direction Vanderbilt International (IRL) Ltd. 05.2016... -
Page 16: Connecting The Reader
When employing Wiegand transmission format, the data is transferred using se- quences of pulses sent over the CLOCK and DATA lines. Depending on the se- lected version of the transmission format, the ARS6311-RX uses 26, 34 or 42 bits to transmit a data to a host. -
Page 17: Magstripe Transmission Format
In Magstripe format, the ARS6311-RX send the serial number of the card. The default setting for ARS6311-RX is „ONLINE Mode Magstripe“. As shown in Fig. 4, the ARS6311-RX can for instance be directly connected to SiPass RIM. (SiPass integrated reader technology “Siemens Clk/Data”). -
Page 18: Programming
Programming Programming Before the ARS6311-RX can start operation, it must be configured to adequate Reader Operation Mode. If the unit is set for any of the ONLINE operating modes, it does not require any further programming. If it is set for Stand-alone Operation... -
Page 19: Setting Reader Operation Mode
Programming Setting Reader Operation Mode The ARS6311-RX provides two main modes of operation: ONLINE (reader) and OFFLINE (stand-alone). It also offers several other options which may modify those modes. To select proper Operation Mode you have to program the adequate control code to a reader. -
Page 20: Troubleshooting
11. Once the previous step has been completed the reader automatically ends the programming procedure and enters the Operation Mode. Example: Configuring the ARS6311-RX for Offline Mode - Stand alone Mode (Code 04) Power down the unit. Remove all connections from DATA (bn) and IN1 lines (ye). -
Page 21: Define Master And Installer Cards - Memory Reset
Programming Define Master and Installer Cards - Memory Reset The Memory Reset erases from the ARS6311-RX all cards including previous Master and Installer Cards. Also, it causes the reader to restore factory default set- tings. The Memory Reset is required only if the unit is configured for Stand-alone Mode. -
Page 22: Installer Programming Mode
(ARMED or DISARMED Mode) it was in before entering installer programming. NOTE As mentioned earlier programming of ARS6311-RX is achieved through multiple readings of an ade- quate Programming Card. Here, for programming of C1..C11 digits, the Installer Card has to be used. NOTE If you don’t present the Installer Card within 20 s time the reader will leave programming mode without... -
Page 23: Configuration Example Settings
Programming Mode and returns to the Operating mode (ARMED or DISARMED Mode) which it was in before entering Installer Programming Mode. NOTE Installer Programming Mode can be accessed only if the reader was earlier configured for Stand-alone Operation Mode. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 24: List Of The Installer Programming Modes
If the „door feedback contact“ and the „door alarm output“ are activated and the door is forced open, the card reader will produce an audible alarm signal. In order to deactivate the buzzer on the reader after a door alarm, the door must be closed and opened again using a valid card. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 25: User Programming Mode
ID index. Exit User Programming Mode [#] After exiting User Programming Mode the reader returns to the Opera- tion Mode (ARMED or DISARMED Mode) it was in before entering User Programming Mode. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 26: Programming Examples
The reader deletes the user with ID=045 from its memory, however, it re- mains in User Programming Mode, so that you may use your next desired programming command or you may leave this programming mode. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 27: Appendix
Appendix Appendix Dimensions Fig. 5 Dimensions Tamper Electronic circuit board (fully potted) Cable length 400 mm LED STATUS (ARMED/DISARMED Mode) LED OPEN LED SYSTEM Vanderbilt International (IRL) Ltd. 05.2016... -
Page 28: Various Example Connections
Reader in Stand-alone Mode - I/O Board Fig. 6 Stand-alone Mode Door Lock Door Contact (NC type) Exit Button (NO type) Alarm Signaling Device Buffered Power Supply NOTE Always set address ID=5 at the ACS6311. Vanderbilt International (IRL) Ltd. 05.2016... -
Page 29: Maintenance
Appendix Maintenance Defective modules should be sent to the nearest Vanderbilt office to be forwarded to the service centre. Disposal All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. -
Page 30: List Of Users
Appendix List of Users Site name: Reader location: ID number Card number Type User name Master Installer Vanderbilt International (IRL) Ltd. 05.2016... - Page 31 Appendix List of Users Site name: Reader location: ID number Card number Type User name Vanderbilt International (IRL) Ltd. 05.2016...
- Page 32 Issued by Vanderbilt International (IRL) Ltd. Clonshaugh Business and Technology Park Clonshaugh Dublin 17 © 2015 Copyright by Vanderbilt International (IRL) Ltd. Ireland Data and design subject to change without notice. Supply subject to availability. www.vanderbiltindustries.com Document no. A24205-A335-B291 Edition...
Need help?
Do you have a question about the ARS6311-RX and is the answer not in the manual?
Questions and answers