Keypad/ID code Function Description Activate keypad: Touch the key pad in the center. ◆ Lock: Press【#】 ◆ Unlock: Password code +【#】. ◆ Back/Exit: Press【*】 ◆ Confirm: Press【#】 ◆ System will exit when its not operated for more than 8 seconds. ◆...
Page 4
2. Add normal users (Total of 82 users can be added. ID NO. 18 to Long press【#】——input administrator code ——press【#】 ——press[1] ——press[1]——press[1]——input code card——press【#】——input code——press【#】 (Note: You only need to enter the card once.). 3. Add one-time users (Total of 5 users can be added. ID NO. 3 to 5) Long press【#】——input administrator...
Page 5
7. Manual/automatic lock setting Long press【#】——input administrator code——press【#】 ——press[2]——press[2] ——press [3] ——press[1] manual or [2] auto lock. (Note: automatic lock time setting is 1-99S.). 8. Volume setting Long press【#】——input administrator code——press【#】 ——press[2] ——press [3]——press [3] ——Press [1] volume up or [2] volume down 9.
Page 7
2. AP Network Operate (if your home WiFi signal is weak please choose AP mode) On lock: press【#】→ input administrator code→press【#】→ press [2] →press [1]. open "Smart Life" APP→1.add device→2.Security&Sensor→Lock (WiFi)→3.select WIFI network and enter WiFi password →(4.1) just confirm “0” key indicator slowly blink→(4.2) select slow flashing→ 5.choose hotspot to connect→6.
Page 8
9.4 Message notification Open ”Smart Life” app→Me→setting→Notification (Note: Most mobile phones will receive notification when you finish configuration).
Page 9
9.5 Remote unlock request Input 888 # to request remote unlock . The APP will send a notification, then you can unlock remotely on the app within 90S. 9.6 Temporary password (ID NO.8~17) You can generate temporary passwords manually or automatically to send to the guests.
Page 10
2.Anti-Peeping Password You can input any code before and after the right password to unlock the door. Such as: ①※※※※※+666888 ②666888+※※※ ③※※666888+※※※ 3.Emergency key unlock Remove the cover on the lock keypad, insert the emergency key to unlock the door. (Tip: You can place the key outside the door in case of equipment failure or dead battery.) 4.Emergency power supply...
Page 11
7.Low voltage alarm If the voltage is lower than 4.6V, the lock will prompt and flash.
Page 12
8.Reset to factory settings Remove the back panel, press the reset button for 3 seconds. After resetting, the administrator password changes to 666888, all data will be deleted. Contents list Cross recessed battery cover screws fixing plate Tools needed: 1.Screwdriver front panel 2.Ruler latch...
Installation Adjust the length New door: 1. Making 2 holes, one of 10mm, and the other of 55mm. The distance between the two holes is 67.3mm. 2. Distance from the center of the door hole to the edge is 60/70mm. 3.
Page 14
3. Install the latch, check that 4. Install the strike plate the latch direction is correct. direction Cross recessed Cross recessed screws S74*24 screws S74*24 5. Make sure the direction of the door is set correctly on the lock, then install the front plate.
Page 15
6.Install fixing plate 7. Install the back panel, please make sure placement is correct. Same direction Cross recessed screw Cross recessed screw M4*20 M4*20 Battery cover...
Page 16
Smart Door Lock OM7-B User Manual w w w . s m a r t o m n i a . c o m smart.omnia smartomniacr...