Omnia LEVEL Smart Deadbolt with Plate Instructions

+
OMNIA LEVEL
Smart Deadbolt with Plate
Instructions/Template for Single Cylinder
A
B
C
U
H
K
V
J
X
L
I
V
Q
R
S
O
P
W
Parts Enclosed:
M - Level Deadbolt Housing
A - Tailpiece Cylinder with Studs
N - Hub of Level Bolt
B - Cylinder Collar
O - Tubular Latch
C - Exterior Backplate
P - Tubular Latch Faceplate
D - Mounting Plate for Cylinder
Q - Tubular Latch Strike
E - 2 – 2" Cylinder Mounting
Screws R - Tubular Latch Dust Box
F - Inside Backplate S - 2 – 1" Mounting Screws for
Tubular Latch Faceplate
G - 2 – 1 / " Mounting Screws
3
4
for Inside Backplate T - Spindle (Tear drop groove
positioned towards set screw)
H - Level Strike
U - 2 Levers
I - 2 – 1 1 / " Mounting Screws
2
V - 2 – 1" Mounting Screws for
for Level Strike
Level Deadbolt Faceplate
J - Level Battery Cap
W - 2 – 1" Mounting Screws for
K - CR2 Battery
Tubular Latch Strike
L - Level Deadbolt
X - 2 – Set Screws
Tools Needed:
Doors Prepared with 2 1 / " Cutout
8
1 - No.1 and No.2 Phillips screwdrivers
2 - Measuring device
3 - Flathead screwdriver
4 - Pliers or hacksaw
5 - Metal file
800 - 310 - 7960 / www.OMNIAindustries.com
(Stainless Steel)
D
E
G
M
N
E
F
U
X
T
G
N
A
B
A
B
C
X
L
V
(L)
(S)
M
N
V
Adjust backset on L for door, 2 3
1
3 " (L). Insert L through
(S) or 2 /
4
edge of door deadbolt hole and
fasten to door with V wood
screws. Insert M into 2
1 / " bore
8
and fit N into M.
Slide A through
4
B and C and
then insert end of
C
tailpiece into hub
of M. Test fit length
of tailpiece into F
on other side of
door to determine
where to trim the
tailpiece.
M
M
D
E
In lower hole on door edge, install latch and faceplate
2
and insert spindle through latch hub (Not Shown).
Follow latchset instruction sheet provided separately.
/ "
8
M
L
While M is inside of 2 " bore, attach L to M
1 /
8
3
using screw already assembled to body of M.
Trim the appropriate amount of length from tailpiece
5
using either a hacksaw or break with a pair of pliers.
The tailpiece may need to be filed down to assure proper
movement of the Level bolt when used electronically.
(May work manually, but not electronically. Tailpiece
may be too long.) Remove studs on cylinder, if required.
Slide A through B and C and then
6
slide tailpiece through hub of M
and large hole of D. The lever attached
to the backplate needs to slide onto
the spindle in hole below. From interior
side, insert the two E screws through
G
E
D and M and tighten into A. Attach
F so that the tailpiece slides into the
turnpiece and the spindle below slides
into the lever attached to the backplate.
Fasten at both ends of backplate using
G screws. On both sides of door, secure
F
levers with set screw X.
M
O + L- DBw/PlateSS 0522