Sony DVP-NS3100ES Service Manual page 14

DVP-NS3100ES
1-1. DVD Single Layer Disc
Select [1], insert DVD single layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the SL disc is set on
the disc tray.
DVD Single Layer Disc Adjustment Steps
1. Sled Reset
2. Set Disc Type SL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tracking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. All Servo Off
1-2. CD Disc
Select [2], insert CD disc, and press [ENTER] key, and the adjustment
will be made through the following steps, then adjusted values will
be written to the flash memory. If there is no disc on the disc tray,
the tray will be open to wait for closing. If there is a disc on the disc
tray, the adjustment starts immediately. If you put a disc prior to
adjustment, confirm that the CD is set on the disc tray.
CD Adjustment Steps
1. Sled Reset
2. Set Disc Type CD
3. Laser Diode (CD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Auto Focus Gain Adjust
13. Auto Tracking Gain Adjust
14. Sled ON
15. CLV ON
16. Auto Focus Balance Adjust
17. Auto RFEQ Boost Adjust
18. Jitter measure
19. Search Check
20. All Servo Off
14
1-3. DVD Dual Layer Disc (Parallel)
Select [3], insert DVD dual layer disc, and press [ENTER] key, and
the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the DL disc is set on
the disc tray.
DVD Dual Layer Disc Adjustment Steps
1. Sled Reset
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. Focus Jump (L0 t L1)
25. Tracking Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off
1-4. ALL (DL: Opposite)
Select [4] and press the [ENTER] key. Then, [1] DVD-SL disc, [2]
CD disc, and [5] DVD-DL (Opposite) disc are adjusted in this order.
Each time one disc was adjusted, it is ejected, and therefore exchange
the disc following the message. You can exit the adjustment by
pressing the button. In adjusting each disc, the mirror time is
x
measured to check the disc type. In the auto adjustment, whether
the disc type is correct is not checked unlike conventional models,
and accordingly, take care not to insert a different type of disc.
Set Disc
1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-504)
2: CD (LUV-P01 or YEDS-18 or PATD-012)
3: DVD-DL (TDV-540C only)