Black & Decker BEHB101 Original Instructions Manual page 21

Making a Drink (Fig. F - J)

WARNING: To ensure liquor is not dispensed while
making a mocktail, lift straw locks
bottles and keep the water bottle straw lock down.
1. Turn the cocktail maker on as described in the ON/
OFF section.
2. Place a glass or shaker on the glass shelf
depending on its height as described in the CHOOSE A GLASS
TRAY section.
3. Insert the desired capsule
described in the INSERTING CAPSULE section.
4. Turn the strength selector dial
as described in the SELECT ALCOHOL STRENGTH section.
5. Bottles used for the drink recipe will light up. Ensure bottles
are installed in all locations illuminated.
6. Push the mix button 26
7. The bottle LED will light under the bottle whose liquid is
being dispensed.
8. It is complete when all the LEDs become solid.
9. Remove the capsule before removing the glass. The capsule
may drip when it is being removed and if left in the holder.
nOTE: While making a drink, if the power button is turned off, the
appliance is unplugged, or after two minutes in pause mode, the
mixing process will be reset, ending the mixing of the current drink. If
this happens, a small amount of alcohol may remain in the internal lines.
To ensure the next drink is not mixed with this remaining alcohol, clean
the lines as described in the CLEANING MODE section before mixing
another drink. To resume making the drink while in pause mode, refer to
the PAUSE MODE section.
nOTE: If the cocktail maker continues to dispense to the point
of overflow, turn the appliance off, lift the straw lock, or lift the
capsule holder lid 22 .
Bottle Runs Out During Mixing (Fig. F, J)
If a bottle runs out of liquid while the cocktail maker is mixing
a drink:
• The cocktail mixer will enter pause mode for 2 minutes to
allow you to replace the empty bottle. Refer to the PAUSE
MODE section for more information.
• Do not turn the power switch
the mixing process and the cartridge will no longer be able
to be used.
nOTE: The unit will not flush the lines while the capsule holder
lid 22 is lifted.
To replace the empty bottle:
1. Remove the bottle as described in the REMOVING
BOTTLES section.
2. Install the a new bottle as described in the INSTALLING
BOTTLES section.
3. Press the mix button 26
where it left off.
Pause Mode
Pause mode lasts for 2 minutes. The strength LEDs
8 for the alcohol
17 or drip tray
20 into the capsule holder
25 to set the alcohol content
to begin making a drink.
14 off. Turning it off will reset
to resume mixing the drink from
15 will light
to indicate the time remaining.
3 solid, 1 flashing
2 solid, 1 flashing
1 solid, 1 flashing
1 flashing
3
• Press and hold the mix button for 3 seconds to cancel
pause mode.
• If the LED countdown finishes before the drink mixing
21 as
resumes or pause mode is cancelled, the unit will pump a
small amount of water to flush the lines. The cocktail maker
will reset to its original mode and the drink will no longer
be mixed. If there is no water loaded into the cocktail maker,
the unit will flush the lines with air.
nOTE: The unit will not flush the lines while the capsule holder
lid 22 is lifted.
Pause mode is triggered three ways.
• The mix button is pressed.
- Press the mix button once more to resume.
• The capsule holder lid is open.
- Close the lid and press the mix button.
• A bottle runs out of liquid
- Replace the empty bottle as described in the BOTTLE
RUNS OUT DURING MIXING section.
Turn on Party Mode LEDs (Fig. K)
The bottle LEDs
1. Turn the cocktail maker on by pushing the "I" side of the
power switch
2. Press the party mode button
The LEDs will begin flashing.
3. Press the party mode button a second time to turn all bottle
LEDs off..
4. Press the party mode button a third time to turn all bottle
LEDs back on.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and keep away from power
button before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Your BLACK+DECKER appliance has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
appliance care and regular cleaning.
Cleaning (Fig. C)

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the appliance; never
immerse any part of the appliance into a liquid.
1:30 - 2 min. remaining
1 - 1:30 min. remaining
30 sec. - 1 minute remaining
less than 30 sec.
16 can be set to flash in a preset pattern.
14 . All 6 bottle LEDs will light.
27 once to set party mode.
EnGLIsH
19