AQL EVADE - Wireless Stereo Bluetooth Headset Manual

Description

1. MF (multifunction) button
2. LED
3. Led Charging Case
4. USB-C charging port
5. USB to USB-C charging cable

PRELIMINARY OPERATIONS

Recharge Charging Case

Charging Case has an internal battery which allows the earbuds to be recharged without being plugged in to a mains charger. The Charging Case must therefore be charged before recharging the batteries of the devices.

Connect the charging cable to a USB port then connect the other end to the USB-C charging port (4); the four LEDs will gradually turn on (3) to show the battery charge level.

Once you have finished recharging, disconnect the Charging Case from the power supply.

Recharging the earbuds

Insert the devices in their respective docks and close the Charging Case flap, charging will start automatically. The red LED (2) turns on when charging is in progress. The LED (2) turns off when charging is complete.

Connection

Before connecting EVADE to the phone, it is necessary to establish a connection between the two earbuds.

Remove the individual earbuds from the charging dock. Both will automatically turn on and the LEDs (2) will begin to flash. They will connect with each other within a few seconds.

Once the TWS connection has been established, the LED (2) on one of the earbuds will flash quickly, indicating that pairing mode is active. Follow the instructions displayed on the phone to search for the unit.

Turn on Bluetooth^® on your phone to run a search for devices and select EVADE when it is detected.

If the earbuds or mobile phone have been turned off or placed out of range, in order to pair them again, it may be necessary to access the mobile phone menu or simply press the MFB button (1) as if you were answering a call.

USING THE DEVICE IN STEREO MODE

Switching on

Hold down the MFB button (1) for about 2 seconds or remove the devices from the Charging Case.

Switching off

Hold down the MFB button (1) for about 2 seconds or insert the devices in the Charging Case.

To answer a call

You can answer calls from both earbuds by pressing the MF button (1). If both earbuds are inside the Charging Case when there is an incoming call, take out the right or left earbud, wait for the connection and then answer by pressing the MF button.

To end a call

Press the MF button (1) briefly.

Refuse an incoming call

Press the MFB button for 1 second when there is an incoming call.

Voice assistant

Press the MFI button (1) three times

Dial the last number

Press the MFI button (1) four times

Play/Pause

Press the MF button (1)

FF

Keep the MFB button (1) on the right earbud pressed for one second.

Rew

Keep the MFB button (1) on the left earbud pressed for one second.

Increase the volume

Press the MFB button (1) on the right earbud twice.

Decrease the volume

Press the MFB button (1) on the left earbud twice.

Flat battery indicator

If the LED flashes red, the battery is flat.

Reset

If the device does not work properly, it is possible to carry out a reset to restore factory settings.

• Take the devices out of the Charging Case and turn them off by pressing the buttons until the LEDs blink red. Release the buttons.
• Keep both MF buttons (1) pressed for 10 seconds. The LEDs will initially flash white, and then they will flash red and white alternately and then red and white together. Release the buttons.
• After this last flash, the devices will switch off. Return them to the dock and repeat the phone pairing procedure.

HEADSET TECHNICAL SPECIFICATIONS

Bluetooth^®: v5.0

Supported profiles: Headset – Handsfree – A2DP - AVRCP

Range: 10m

Bluetooth^® frequency range: 2.4GHz-2.48GHz

Battery voltage: 3.7V

Battery capacity: 50mAh X 2

Charging Case battery capacity: 550mAh

Micro-USB port voltage (V): 5V

Micro-USB port current (A): 40mAh

ERP output: -1.5bBm

SAR: 1.5W/kg

Autonomy in standby: 20 hours

Talk time: 5 hours

Playback time: 5 hours

Charging the earbuds: about 1.5 hours

Charging Case Charge: about 2 hrs

Weight: 41g