AQL PLUME - Wireless Stereo Bluetooth Headset Manual

Description

1. MF button
2. LED
3. Earbud dock
4. Battery level indicator LED
5. Micro-USB charging port
6. Charge cable

PRELIMINARY OPERATIONS

Charging Case Charge: charging Case has an internal battery which allows the earbuds to be recharged without being plugged in to a mains charger. Charging Case must therefore be charged before it can recharge the earbuds.

Connect the charge cable to a powered USB port or charger and connect the other end to the Micro-USB charging port (5); the four LEDs (4) will gradually turn on to show the battery charge level.

Charging the earbuds: insert the individual earbuds into the corresponding docks and close the Charging Case flap; charging will begin automatically. The red LEDs (2) on the earbuds turn on when charging is in progress. The LEDs (2) turn off when charging is complete.

Earbud TWS Connection: remove the individual earbuds from the charging dock. Both will automatically turn on and the LEDs (2) will begin to flash white. They will connect within a few seconds.

Pairing with your phone: once the TWS connection has been established, the LED (2) on one of the earbuds will flash red - white, indicating that pairing mode is active. Turn on Bluetooth®® on your phone to run a search for devices and select PLUME when it appears.

Pairing a single earbud with your phone: switch off the earbuds and put them inside Charging Case.

Take only one earbud out of the case, turn on Bluetooth®® on your phone to run a search for devices and select PLUME when it appears. The white LED on the earbud will flash to indicate that pairing has been successful. If this does not happen, turn it off and try again.

Pairing the device with a second phone (Multipoint function): IMPORTANT: the multipoint mode lets you connect two phones to only one earbud.

Turn Bluetooth® off on the first phone

To connect to the second phone, refer to the section "Pairing a single earbud with your phone".

Once the connection has been established with the second phone, turn on Bluetooth® on the first phone and select PLUME if it does not connect automatically.

Power ON:remove the earbuds from the case

Power OFF:hold down the MF button (1) until the LED flashes red (approx. 3 seconds)

if the earbud or mobile phone have been turned off or taken out of range, in order to pair them again, it may be necessary to access the menu on the mobile phone, or simply to press the MF button (1) as if you were answering a call.

USING THE EARBUDS FOR A PHONE CALL

To answer a call: press the MF button (1) briefly.

To end a call: press the MF button (1) briefly.

Speaker volume control: use the phone's volume buttons to ad¬just the call volume.

Flat battery indicator: if the LED flashes red, the battery is flat.

TO PLAY MUSIC

Play/Pause: press the MF button (1)

FFW (next track): press the MF button on the right earbud twice

REW: (previous track): press the MF button on the left earbud twice

Speaker volume control: use the phone's volume but¬tons to adjust the volume.

EARBUDS TECHNICAL SPECIFICATIONS

Bluetooth®: v5

Bluetooth® Frequency: 2.402-2.80 GHz

Supported profiles: Headset – Handsfree – A2DP - AVRCP

Range: 10 m

Impedance: 32 Ohm

Sensitivity: -92 dB

Driver dimensions: 6 mm diameter

Stand-by time: 1800 hrs (earbuds)

Talk time: 4 hrs (earbuds)

Play time: 4 hrs (earbuds)

Charging time: 2 hrs

Weight: 36 g

Micro-USB port voltage (V): 5 V Micro-USB port current (A): 1 A

Battery voltage (V): 3.7 V

Battery capacity (mAh): 2 x 55 mAh

ERP output: 3 mW

Frequency range: 90 Hz-18 kHz

CHARGING CASE TECHNICAL SPECIFICATIONS:

Battery capacity: 300 mAh, 1.11 Wh

Input: 5 V, 350 mA

Charging time: 2 hrs

Cellular Italia S.p. A, a single-member company, declares that this Bluetooth® headset complies with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following address: www.cellularline.com/_/declaration-of-conformity

Cellular Italia S.p. A, a single-member company, also declares that this Bluetooth® headset complies with the RoHS Directive 2011/65/EU.

INFORMATION ON THE STATUTORY WARRANTY

Our products are covered by a statutory warranty against conformity defects in accordance with applicable national consumer protection laws. For more information, please see the following page www.cellularline.com/_/warranty