Philips 107B40 User Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Monitor
  5. 107B40
  6. User manual

Philips 107B40 User Manual

Philips 107b40: user guide
Hide thumbs Also See for 107B40:
Table of Contents

Advertisement

Quick Links

Download this manual
electronic user's manual
file:///D|/EDFU/LF3/lf3manual/english/107B/manual.html [2002/9/2 ?? 04:04:04]

Advertisement

Table of Contents
loading

Related Manuals for Philips 107B40

Summary of Contents for Philips 107B40

  • Page 1 electronic user's manual file:///D|/EDFU/LF3/lf3manual/english/107B/manual.html [2002/9/2 ?? 04:04:04]...

  • Page 2: Safety And Troubleshooting Information

    Do not place objects on top of the monitor cabinet, objects could fall into vents or cover them and prevent proper cooling of the monitor's electronic devices. To avoid the risk of shock or permanent damage to the set, do not expose the monitor to rain or excessive moisture.
  • Page 3 Other Documents You May Need About This Guide This electronic user's guide is intended for anyone who uses the Philips Color Monitor. It describes the monitor's features, setup, operation and all other information, which is the same exact information described in our printed version.
  • Page 4 ©2002 Koninklijke Philips Electronics N.V. All rights reserved. Reproduction, copying, usage, modifying, hiring, renting, public performance, transmission and/or broadcasting in whole or in part is prohibited without written consent of Philips Electronics N.V. file:///D|/EDFU/LF3/lf3manual/english/107B/ABOUT/ABOUT.HTM (2 of 2) [2002/9/2 ?? 04:04:30]...

  • Page 5: Product Information

    It is recommended that you install this software only on a Philips monitor designed to use it. These monitors can be identified by the LightFrame™ logo on the front of the monitor.
  • Page 6 If LightFrame™ detects that your monitor is not LightFrame™ compatible, a message appears on the monitor screen. If you see this message, you can select to abort or continue the installation. However, if you continue the installation, LightFrame™ will probably not work on the monitor.
  • Page 7 107B Product Information A: No. If you run LightFrame™; 1 or 2 software with a Philips LightFrame™ 3 monitor, nothing will happen. Q:Can I use LightFrame™ 3 software on my LightFrame™ 1 / 2 monitor. A:No for a LightFrame™ 1 or 2 monitor you need to use LightFrame™ 1 or 2 software. It is however possible to use the LightFrame™...
  • Page 8 A:Nothing is wrong. The effect which you see is due to the sharpness enhancement that LightFrame™ is doing on your monitor. This sharpness improves a photo or video significantly however on black text on a light background the effect is less favorable. Please keep in mind that LightFrame™ is developed to enhance your photos and videos and not really for text or synthetic pictures.

  • Page 9: Technical Specifications

    107B Product Information Q: How do I use the LightFrame™ 3 control bar that appears at the top my screen? A: The control bar is another upgrade that helps you run all LightFrame™ 3 s neat, new features. The illustration below describes the tasks each button performs. Accustomed to working with the original LightFrame™...

  • Page 10: White Color Temperature

    Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.

  • Page 11: Energy Star

    107B Product Information Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up".

  • Page 12: Pin Assignment

    107B Product Information • Temperature (storage) • Relative humidity (storage) * Resolution 1280 x 1024, standard size, contrast max., brightness 50%, 9300 * These information are subject to change without notice. Pin Assignment The 15-pin D-sub connector (male) of the signal cable (IBM systems): Assignment Red video input Green video input...

  • Page 13: Front View

    107B Product Information Follow the links to see various views of the monitor and its components. Front View Rear View file:///D|/EDFU/LF3/lf3manual/english/107B/PRODUCT/PRODUCT.HTM (9 of 9) [2002/9/2 ?? 04:04:30] RETURN TO TOP OF THE PAGE...

  • Page 14: Installing Your Monitor

    • 6G3B11 Multimedia Base (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up.

  • Page 15: Rear View

    Installing your Monitor UP and DOWN buttons are used when adjusting the OSD of your monitor Brightness hotkey. When the RIGHT arrow is pressed, the adjustment controls for BRIGHTNESS will show up. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor.
  • Page 16 Installing your Monitor Power in - attach power cable here. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC. file:///D|/EDFU/LF3/lf3manual/english/INSTALL_2/INSTALL.HTM (3 of 3) [2002/9/2 ?? 04:04:31]...

  • Page 17: On-Screen Display

    Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor.
  • Page 18 On-Screen Display The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. file:///D|/EDFU/LF3/lf3manual/english/OSD/OSDDESC.HTM (2 of 3) [2002/9/2 ?? 04:04:31] RETURN TO TOP OF THE PAGE...
  • Page 19 On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/EDFU/LF3/lf3manual/english/OSD/OSDDESC.HTM (3 of 3) [2002/9/2 ?? 04:04:31]...

  • Page 20: Customer Care And Warranty

    Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland •...
  • Page 21 Increasingly, monitors include USB hub functionality. But not all users need or want a USB hub. To give users freedom of choice, Philips provides an optional USB hub (type number PCUH411). The USB hub consists of two parts that are normally connected: one is functional, the other aesthetic.
  • Page 22 Philips monitors. Contact your dealer/reseller for details. What models are Mac compatible? All listed Philips monitors are Mac compatible. BUT, you may need an adapter to connect the monitor to your Mac system. Please contact your dealer/reseller for details.
  • Page 23 Go to 'My Computer' and select 'Control Panel' followed by 'Monitor Control.' Select "All default selection' and choose your Philips monitor model from the default driver list. Plug and Play will automatically enable the EPA tick box for you. In DOS or Windows 3.1, you must first make sure your PC supports power saving.
  • Page 24 16. What is LightFrame " LightFrame is a Philips technology breakthrough which offers a unique and revolutionary solution for boosting a monitor 's brightness and sharpness. With LightFrame experiences TV quality performance for video or photos without deterioration to the monitor 's performance in windows used for other applications.
  • Page 25 Only a Philips driver can determine if your monitor is equipped with LightFrame Windows driver cannot. Install the special Philips driver that came with your monitor. If the warning continues to flash after your Philips driver is installed, ignore the message.
  • Page 26 25. What is Philips monitors' solution for audio? Not all users need multimedia capabilities. To give users freedom of choice, Philips provides an optional Multimedia Base (type number: 6G3B10). The Multimedia Base replaces the easily removable standard pedestal of the monitor.
  • Page 27 Only the monitor's height is increased by only 3 centimeters. 29. Where can I buy a multimedia base to incorporate with my Philips monitor? Please contact your dealer/reseller for details.
  • Page 28 Auto Calibration takes place when a monitor receives a signal indicating an imminent switch to its sleep mode/stand-by mode. 34. Which models of Philips monitors are equipped with Auto Calibrate feature? Auto Calibrate is currently available in the new 201P, 201B and 109P.
  • Page 29 Change horizontal and vertical size to optimize the reduction of the Moir¨² effect. 39. What is CustoMax? CustoMax is proprietary Philips software that allows user to control parameter (e.g. Size, Color, Geometry) in place of the buttons on the front of the monitor. To install and run the CustoMax software, you must have a USB compatible system and have a USB connection at the rear of your monitor.
  • Page 30 Philips monitors. Please be aware that not all models in the Philips range has this manual degauss function. Some models are built with an auto degauss feature which automatically degausses the monitor when it is switched on.
  • Page 31 Set the Contrast to maximum level (100) and Brightness to middle level (50) Video card could be defective (try the monitor with another computer) 45. I have noticed two thin horizontal lines on the screen of my Philips monitor. Is this normal? This phenomenon can occur with Philips 107P, 109P and 201P monitors and is normal.
  • Page 32 50. Why does the picture disappear after I press the on/off button quickly? This is a unique Philips feature designed to preserve the life of your monitor. Please allow 5 seconds between powering off and on your monitor, your picture will then be restored.
  • Page 33 L M N O P Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus operate with a wide range of video cards. MultiSync, a registered trademark of NEC, provides a similar function.

  • Page 34: Color Temperature

    A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired value. Contrast The ratio between the brightness of the brightest and darkest parts of a picture.
  • Page 35 TV and monitor picture tube. CustoMax Philips proprietary monitor control software that allows users to control parameters (e.g., Size, Color, Geometry) using software running in Windows. CustoMax is compatible with existing VGA cards. See CrystalClear FAQ and USB Bay FAQ.
  • Page 36 DDC is implemented as part of the new Plug & Play approach introduced into the PC market to increase user friendliness. The three levels developed for Plug & play are: (1) DDC1, monitor send data to the PC; (2) DDC2B, PC can request information from monitor; and (3) DDC2Bi which is a two-way communication - monitor can be addressed and PC or graphics board can give commands to monitor.
  • Page 37 MPR-II defines maximum permitted electrostatic, magnetic and electric field levels measured at a distance of 50 cm from the center of the monitor (see table). file:///D|/EDFU/LF3/lf3manual/english/GLOSSARY/GLOSSARY.HTM (5 of 18) [2002/9/2 ?? 04:04:33]...
  • Page 38 The problem can, however, be eliminated by increasing the refresh rate (number of frames/second) of the monitor to a value above around 70 Hz. Sensitivity to flicker appears to diminish with increasing age.
  • Page 39 Glossary Also called line frequency and expressed in kHz, it is the number of video lines written on the screen every second (from left to right). The higher the horizontal scanning frequency, the better the resolution (i.e., the higher the resolution and/or the higher the refresh rate). INF File INF file (Information File) Information (INF) files store information in a specific format.
  • Page 40 Alternating fields generated by the deflection yoke. These are subject to increasing attention, notably by governing authorities, the trade and the press. Although there is no scientific evidence that monitor emissions are harmful, much effort has gone into reducing emissions on the principle of better safe than sorry.
  • Page 41 A fringe pattern arising from the interference between two superimposed line patterns. In a monitor it comes from the interference between the shadow mask pattern and the video information (video moiré), and between the shadow mask pattern and the horizontal line pattern (scan moiré). It shows itself as wavy patterns on the screen and becomes more noticeable as monitor resolution increases.
  • Page 42 Abbreviation for picture element, the smallest element of the picture that can be displayed on the screen. The smaller the pixel size, the better the resolution of the monitor. Pixel size is determined by the size of the electron spot on the screen and not necessarily by the phosphor dot pitch (the size of the triad). Thus, a monitor with a large electron spot covering several triads can exhibit poor resolution even though its dot pitch is small.

  • Page 43: Refresh Rate

    Rotation function The feature that allows users to adjust the whole screen rotating to be horizontal. Because of the magnetic field of earth, the screen of monitor will be tilt when the screen faces toward the different direction. Screen coatings file:///D|/EDFU/LF3/lf3manual/english/GLOSSARY/GLOSSARY.HTM (11 of 18) [2002/9/2 ?? 04:04:33]...
  • Page 44 Glossary Anti-Static coatings Due to bombardment by beam electrons, monitor screens become electrically charged when in use. Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away the charge and prevents screen dust build-up.
  • Page 45 AGRAS (Anti-Glare anti-Reflection Anti-Static) coating. A combined anti-reflection, anti-glare, anti-static coating. Self-test function A monitor equipped with hardware or software to automatically detect cable connection status. Shape Deviation of a reproduced picture from its intended shape. The following types of distortion are most common: file:///D|/EDFU/LF3/lf3manual/english/GLOSSARY/GLOSSARY.HTM (13 of 18) [2002/9/2 ?? 04:04:33]...
  • Page 46 A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse, red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor using one of three methods: 1.
  • Page 47 A TTL-driven monitor can thus display a maximum of 64 colors. Video standards such as MDA, CGA and EGA are based on TTL level.
  • Page 48 It also has hardware support for reset and suspend/resume signaling. The controller provides the interface registers to allow communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports.
  • Page 49 A card equipped with a character or graphic generator and video memory, which maps to the screen. A microprocessor scans video memory and translates bit information from the computer into displayable video signals for the monitor. These cards comply with various standards that determine the nature and quality of the display.
  • Page 50 The real screen dimensions that users can see measured diagonally. The VIS of a monitor is always less than the so called screen size of a monitor. For example, the VIS of a 17-inch monitor is only about 16 inches. It depends on the useful screen size of CRT and the opening of a monitor's front cabinet.

  • Page 51: Download And Print

    Download and Print Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Acrobat Reader for PC Adobe®...
  • Page 52 Download and Print 109B.pdf 109S.pdf file:///D|/EDFU/LF3/lf3manual/english/DOWNLOAD/DOWNLOAD.HTM (2 of 2) [2002/9/2 ?? 04:04:33]...

  • Page 53: Troubleshooting

    Make sure the Power cable is plugged into the power outlet and back of the monitor. Power button on top of the monitor should be in the ON position. Disconnect the monitor from the power outlet for about one minute.
  • Page 54 Adjust the geometry. Eliminate the use of a video extension cable and/or video switch box. Face the monitor toward the East for the best picture quality. Check to make sure Moiré is switched off. Adjust Sync Input. Increase your refresh rate.

  • Page 55: Regulatory Information

    • Information for UK only Safety Precautions and Maintenance TCO '99 Information ( for 107B40) • TCO '99 : Available on 105S, 105B, 107E, 107T, 107B, 107P, 109S, 109B. Congratulations! labeled product! Your choice has provided you with a product developed for professional use.
  • Page 56 Regulatory Information TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labeled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
  • Page 57 Regulatory Information • TCO '95 : Available on 107B,107E, 107T, 107X,109B. Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also, to the further development of environmentally adapted electronics products.
  • Page 58 Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative. CE Declaration of Conformity Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards - EN60950:1992+A1+A2+A3+A4+A11 (Safety requirement of Information Technology Equipment) - EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)
  • Page 59 NERGY NERGY We recommend you switch off the monitor when it is not in use for quite a long time. Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 60 Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
  • Page 61 The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
  • Page 62 Regulatory Information North Europe Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
  • Page 63 Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer. file:///D|/EDFU/LF3/lf3manual/english/107B/SAFETY/regs/regulat.htm (9 of 10) [2002/9/2 ?? 04:05:03]...
  • Page 64 Regulatory Information Information for UK only file:///D|/EDFU/LF3/lf3manual/english/107B/SAFETY/regs/regulat.htm (10 of 10) [2002/9/2 ?? 04:05:03] WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1.

  • Page 65: Other Related Information

    Other Related Information Other Related Information Safety Precautions and Maintenance Information for Users in the U. Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
  • Page 66 6G3B11 Multimedia Base (option) 6G3B11 Multimedia Base (option) Front View • Rear View • Technical Specifications your Multimedia Base • Power adapter Installation Technical Specifications* • Output power • Bass Boost • Headphone connection • Microphone in/out • Includes • Dimension •...
  • Page 67 1. To INSTALL Slide the pedestal, aligning with the holes on the side. Then click the back hook into the corresponding hole on the bottom plate of your monitor. Microphone jack Attach your microphone here. Audio In Connect this to the audio output of your PC.

  • Page 68: Power Adapter Installation

    Multimedia Base DC input Note: Please keep least 50 cm ) to avoid cansing unstable monitor picture. file:///D|/EDFU/LF3/lf3manual/english/INSTALL_2/mm_pede/mm_inst.htm (3 of 4) [2002/9/2 ?? 04:05:26] 2. To UN-INSTALL Lift the back hook from the hole on the bottom plate of your monitor.
  • Page 69 6G3B11 Multimedia Base (option) RETURN TO TOP OF THE PAGE file:///D|/EDFU/LF3/lf3manual/english/INSTALL_2/mm_pede/mm_inst.htm (4 of 4) [2002/9/2 ?? 04:05:26]...
  • Page 70 Take out the USB hub from the box. Take off the USB hub cover. Slightly tilt and lift the base of your monitor. Attach the USB hub by clipping into the base. You can reposition the USB hub along the base to suit your needs.
  • Page 71 USB Hub (Optional Feature) file:///D|/EDFU/LF3/lf3manual/english/INSTALL_2/usbhub/usb_inst.htm (2 of 2) [2002/9/2 ?? 04:05:27] RETURN TO TOP OF THE PAGE of the Multimedia Pedestal. Attach the USB hub by sliding-in to the Multimedia base.
  • Page 72 To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light coming from the screen. A 50% brightness is recommended. 1) Press the button on the monitor. The BRIGHTNESS window appears. 2) Press the button to adjust the brightness.
  • Page 73 The ON SCREEN DISPLAY shows its settings in one of eight languages. The default is English, but you can select French, Spanish, German, Italian, Simplify-Chinese, Korea, or Brazilian Portuguese. 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE should be highlighted. 2) Press the button again.
  • Page 74 The OSD Controls 3) Press the button until the desired language is highlighted. 4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted... After returning to MAIN CONTROLS ..

  • Page 75: Input Signal Selection

    INPUT B.? 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until INPUT SIGNAL SELECTION is highlighted.
  • Page 76 ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ZOOM is highlighted.
  • Page 77 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST HORIZONTAL is highlighted.
  • Page 78 The OSD Controls 3) Press the button. The ADJUST HORIZONTAL window appears. POSITION should be highlighted. 4) Press the button to move the image to the left or right. 5) When the position is adjusted, press the to highlight SIZE. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (7 of 27) [2002/9/2 ?? 04:06:18] button to return to MAIN CONTROLS window, or press the...
  • Page 79 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST VERTICAL is highlighted.
  • Page 80 The OSD Controls 3) Press the button. The ADJUST VERTICAL window appears. POSITION should be highlighted. 4) Press the button to move the image up or down. 5) When the position is adjusted, press the to highlight SIZE. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (9 of 27) [2002/9/2 ?? 04:06:18] button to return to MAIN CONTROLS window, or press the...
  • Page 81 PINCUSHION and BALANCED pincushion. Note: use these features only when the picture is not square. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (10 of 27) [2002/9/2 ?? 04:06:18] button.
  • Page 82 The OSD Controls 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button. The SIDE CURVE window appears. PINCUSHION should be highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (11 of 27) [2002/9/2 ?? 04:06:18]...
  • Page 83 The OSD Controls 5) To adjust the pincushion, press the 6) When the pincushion is adjusted, press the to return to the ADJUST SHAPE window. 7) To adjust the balanced pincushion, press the 8) When the balanced pincushion is adjusted, press the window.
  • Page 84 TRAPEZOID and PARALLELOGRAM. Note: use these features only when the picture is not square. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button.
  • Page 85 The OSD Controls 4) Press the button to highlight ADJUST SIDE ANGLES. 5) Press the button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted. 6) To adjust the trapezoid, press the 7) When the trapezoid is adjusted, press the button to return to the ADJUST SHAPE window.
  • Page 86 PINCUSHION and BALANCED pincushion. Note: use this feature only when the picture is not square. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (15 of 27) [2002/9/2 ?? 04:06:18] button.
  • Page 87 The OSD Controls 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the arrow until ROTATE IMAGE is highlighted. 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (16 of 27) [2002/9/2 ?? 04:06:18]...

  • Page 88: Adjust Color

    ...to exit completely, press the ADJUST COLOR Your monitor has three preset options you can choose from. The first option is for GENERAL USE, which is fine for most applications. The second option is for IMAGE MANAGEMENT, which includes projects such as desktop publishing, viewing a DVD from your DVD player or pictures on the World Wide Web, and playing video games.
  • Page 89 The OSD Controls 3) Press the button. The ADJUST COLOR window appears. 4) Press the button to highlight 9300K for GENERAL USE, 6500K for IMAGE MANAGEMENT, 5500K for PHOTO RETOUCH, or USER PRESET. 5) Once you have highlighted GENERAL USE, IMAGE MANAGEMENT, or PHOTO RETOUCH, press the button to confirm you selection and return to the MAIN CONTROLS window.

  • Page 90: Reset To Factory Settings

    The OSD Controls 6a) If USER PRESET is highlighted, press the button to adjust the color red. 6b) When finished with RED, press the to adjust the color green. 6c) When finished GREEN, press the adjust the color blue. 6d) When all adjustments are complete, press the MAIN CONTROLS window.
  • Page 91 The OSD Controls RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until RESET TO FACTORY SETTINGS is highlighted. 3) Press the button.
  • Page 92 EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagnetic build up that may distort the color on your screen. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlighted.
  • Page 93 Note: Use only if necessary. By activating ADJUST MOIRE, sharpness can be affected. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the DOWN CURSOR button until EXTRA CONTROLS is highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (22 of 27) [2002/9/2 ?? 04:06:18] button.
  • Page 94 The OSD Controls 3) Press the button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted. 4) Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted. file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (23 of 27) [2002/9/2 ?? 04:06:18]...
  • Page 95 The OSD Controls 5) To adjust the horizontal moire, press the 6) When the horizontal moire is adjusted, press the 7) To adjust the vertical moire, press the 8) When the vertical moire is adjusted, press the BACK TO MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS .
  • Page 96 The OSD Controls on the LIGHTFRAME function to activate in full screen mode. 1) Press button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlight. 3) Press the button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted.
  • Page 97 The OSD Controls 5) Pess the button. LIGHTFRAME will be activated. 6) Press button to go back to MAIN CONTROLS. Press CLOSE MAIN CONTROLS file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (26 of 27) [2002/9/2 ?? 04:06:18] button again to exit the OSD. RETURN TO TOP OF THE PAGE...
  • Page 98 The OSD Controls RETURN TO TOP OF THE PAGE file:///D|/EDFU/LF3/lf3manual/english/OSD/osd_cont.htm (27 of 27) [2002/9/2 ?? 04:06:18]...
  • Page 99 - the monitor is not defective and is within the specification - the monitor has been altered or repaired by non authorised persons If warranty claims are determined to be invalid, Philips may invoice the customer for all related repair, verification and transportation costs.

  • Page 100: Your International Guarantee

    12 months from date of purchase. This international Philips guarantee complements the existing national guarantee obligations to you of dealers and Philips in the country of purchase and does not affect your statutory rights as a customer.

  • Page 101: Limited Warranty

    A product that has been modified from the original design. Where IS SERVICE AVAILABLE? Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the product, the local Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available).
  • Page 102 Please contact Philips at: (800) 479-6696 One year free parts and one year free labor will be provided at Philips Canada depot or any one of its authorized service centers. REMEMBER... Please record the model and serial numbers found on the product below.
  • Page 103 If you have any problems with your monitor within the second or third year of purchase, we will repair it after it has been sent to the service provider at your expense and returned to you within five working days, free of charge.
  • Page 104 Philips Consumer Electronics. reception problems caused by signal conditions or cable or antenna systems outside the unit.
  • Page 105 Please contact Philips at: (800) 479-6696 Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its authorized service centers. (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties of merchantability or fitness for a particular purpose.
  • Page 106 Just a phone call away Philips’ customer help desks are located worldwide. You can contact Philips Monday - Friday from 08.00 - 20.00 hrs Central European Time (CET) and on Saturdays and Sundays from 10.00 to 18.00 hrs CET by using one of the toll-free numbers.

This manual is also suitable for:

107b407499107b437499107b40/43107b

Table of Contents