Table of Contents
Advertisement
Quick Links
Hello, thanks for purchasing the AtomoSynth Mochika X5 analog synthesizer and sequencer. This is a
quick start guide of the sequencer section.
Let's create, save and load a basic sequence.
Basic operation: create save and load a pattern.
A. Create a pattern.
1. When you turn on the unit it starts an empty init pattern.
2. Push the STEPS encoder (encoder 1), and the display will show "Step On/Off".
3. Now you can turn on individual steps by moving each encoder clockwise, and turn them off by
moving each encoder counter-clockwise, the corresponding LED will light or go dark
accordingly.
4. To access steps 1 to 8, push the 1-8 button, and to access steps 9 to 16 push the 9-16 button.
5. To play the pattern push the PLAY/STOP button and you can listen to the sequence.
6. To see the steps pitches, push the PITCH encoder (encoder 2), and the display will show
"Pitch/CV1".
7. Now if you turn each encoder just one detent, the display will show the step number and the
actual pitch for that step without changing it.
8. To change the pitch of each step, move the corresponding encoder more than one detent, and
the display will show the change in pitch value for that step, and the change will remain.
9. Now push the PLAY/STOP button and you will listen to the sequence with the pitches you just
programmed.
B. Save a pattern.
1. To save a pattern, push the OK/Settings button, and the display will show "Settings".
2. Move the SAVE encoder (encoder 6) and the display will show you the pattern number in which
your sequence will be saved, choose the pattern number you want and then push the
OK/Settings button to confirm.
3. To cancel a Save operation, before you push OK to confirm, just push any other button, for
example, the STEPS encoder.
C. Load a pattern.
1. To see which pattern is loaded, push the OK/Settings button, and move the PATTERN encoder
(encoder 7) just one detent and the display will show you the pattern that is loaded without
changing it.
2. To load a saved pattern, push the OK/Settings button, and move the PATTERN encoder
(encoder 7) more than one detent, the display will show pattern numbers, set the desired
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AtomoSynth Mochika X5
Summary of Contents for AtomoSynth Mochika X5
- Page 1 Hello, thanks for purchasing the AtomoSynth Mochika X5 analog synthesizer and sequencer. This is a quick start guide of the sequencer section. Let's create, save and load a basic sequence. Basic operation: create save and load a pattern. A. Create a pattern.
- Page 2 STEPS encoder. Per-step parameters setting The Mochika X5 can store 8 parameters for each step including step on/off, pitch, two extra voltages CV2 and CV3 used to control other analog modules like filters, also gate time, retrigger, repeat, and probability for each step.
- Page 3 H. Set the CV2 and CV3 values. The Mochika X5 can generate one PITCH voltage which is chromatic scale quantized, and also two nonquantized voltages CV2 and CV3 and store their values for each step.
- Page 4 To save all the changes in the parameters described, perform the “Save a pattern” operation described before in section B. Sequencer Settings. I. Tempo Setting. 1. To set the tempo, push the OK/Settings button, and the display will show “settings”. 2.
- Page 5 M. Synchronization setting. 1. To synchronize the Mochika X5 with an external clock or midi clock, push the OK/Settings button, and the display will show “settings”. 2. Move the Sync encoder (encoder 5) just one detent, the display will show the actual synchronization source without changing it.
- Page 6 When the sequencer is stopped you can play individual notes using an external midi controller connected to the midi input. When the sequencer is playing, you can transpose all the notes of the actual playing pattern using an external midi controller. All rights reserved. AtomoSynth 2022...
Need help?
Do you have a question about the Mochika X5 and is the answer not in the manual?
Questions and answers