Advertisement
Available languages
Available languages
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is suitable for sawing wood, plastic, metal
and building materials on a firm surface. It is suitable for
straight and curved cuts. When using designated suitable bi-
metal saw blades, flush cutting is also possible. The saw
blade recommendations are to be observed.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
a)
(1) Saw blade
(2) Adjustable base plate
(3) Saw blade receptacle
(4) Locking sleeve for saw blade
(5) Stroke speed selector switch
(6) On/off switch
a)
(7) Battery release button
a)
(8) Battery
(9) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating saw
Article number
Stroke rate control
Rated voltage
A)
No-load stroke rate n₀
– first gear
– second gear
Tool holder
Stroke
Max. cutting depth
– in wood
– in steel (unalloyed)
Bosch Power Tools
Reciprocating saw
– pipe diameter
Weight according to
EPTA‑Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperature
during operation
storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Rechargeable battery
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
GSA 18 V-LI
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
3 601 F4J 0..
place by a spring when fitted in the power tool.
●
V=
18
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
−1
min
0–2400
possible to check the state of charge when the power tool is
−1
min
0–2700
not in operation.
SDS
Press the button for the battery charge indicator or
mm
28
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
mm
250
charge indicator, then the battery is defective and must be
mm
20
replaced.
C)
and during
GBA 18V 2.6Ah.
1 609 92A 8E0 | (15.11.2022)
English | 7
GSA 18 V-LI
mm
130
B)
kg
3.2–4.2
°C
0 to +35
°C
−20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
to
Advertisement
