2-way (shared & non-shared) pressure balance trim kit with cartridges and handles 3-way (shared & non-shared) pressure balance trim kit with cartridges and handles (6 pages)
4 piece deckmount tub filler with handshower (10 pages)
Summary of Contents for ALT CIRCO 40721
Page 1
C IR CO #40 72 1 VOL O #1 072 1 Pressure balance trim kit with cartridge and handle Garniture pour valve à pression équilibrée avec cartouche et poignée Installation & Care Guide Guide d’installation et d’entretien VOLO CIRCO last revision: 18/06/2014...
Page 2
Félicitations pour l’achat de purchase of your Alt product votre produit Alt By purchasing an Alt product, you are taking part in En achetant un produit Alt, vous prenez part au the global movement for better living. We take pride in mouvement global pour le mieux-vivre.
Page 3
TRIM KIT COMPONENTS COMPOSANTES DE LA GARNITURE CiRCO mODEL mODèLE CiRCO VOLO mODEL mODèLE VOLO SPECS AT LARGE / SChémA DES PièCES ALT7-7-40-786-01: CIRCO handle / poignée CIRCO ALT7-7-10-786-01: VOLO handle / poignée VOLO ALT7-7-90-707-01: Trim plate / plaque ALT7-90-706-01: decorative sleeve / ensemble de l'anneau décoratif ALT7-90-787-00: cartridge / cartouche...
Page 4
BEFORE YOU START AVANT DE COMMENCER CAUTION: FOR BEST RESULTS, WE STRONGLY miSE EN GARDE: POUR OBTENiR UN RéSULTAT RECOmmEND ThE iNSTALLATiON OF ThiS VALVE BE OPTimAL, NOUS RECOmmANDONS FORTEmENT QUE DONE BY A LiCENSED PROFESSiONAL PLUmBER. L’iNSTALLATiON DE CETTE VALVE SOiT FAiTE PAR UN PLOmBiER PROFESSiONNEL ACCRéDiTé.
INSTALLATION Installing the cartridge First, shut off the 2 check-valves (1) & (2). Afterwards, unscrew the cartridge holder (4) and remove the protective plug (3) (see Fig.1) . Insert the cartridge into the valve body as shown (Fig.2). Screw the cartridge holder (4) back into place. DO NOT OVERTiGhTEN.
Page 6
INSTALLATION Installing the trim kit Insert the decorative sleeve (6) onto the cartridge holder (See Fig.3) then screw the dome cap (7) onto the valve body. Remove protective film from the adhesive seal on the back of the trim. Slide in trim around the valve body and press it firmly against the wall.
INSTALLATION Water temperature adjustment The highest tempature setting has been factory preset at 120˚F (49˚C). however, the preset temperature can be adjusted by following these steps: Remove the decorative cap (1), the setscrew (2) and the volume control handle (3) (See Fig.4). Pull out the temperature stop ring (5) from the cartridge (6).
MAINTENANCE To Service The Cartridge Shut off the main water supply, then remove all the components from (1) to (6). (See Fig.5). Afterwards, shut off the 2 check valves (9) & (10) by turning them clockwise with a screwdriver. Unscrew the cartridge holder (7) and remove the cartridge (8).
Page 9
CARE SOIN To clean your ALT faucet or accessory, wash with a Pour nettoyer et conserver l’apparence de vos wet nonabrasive soapy cloth. Then wipe dry with a robinets ou accesoires ALT, lavez-les avec un linge soft towel or cloth. We recommend this be done on mouillé...
- Any and all ALT products that are subjected to any type of harsh sionnel ou par toute autre personne. abrasive, such as cleaners containing abrasive cleansers, ammonia, - Tout produit ALT nettoyé...
Need help?
Do you have a question about the CIRCO 40721 and is the answer not in the manual?
Questions and answers