Samsung SHS-P717 - Door Lock Manual

Features

Convenient Opening
Easy push/pull handle access

Welcome Function
When a user gets close to the door lock, the authorization standby mode will automatically activate.

Silent-Mode Function
When going in or out, the sound of the key entering and door opening will be suspended.

Automatic Card Reading Function
When a card touches the reader, the reader will conveniently recognize the card.

Double Authorization
Requires card & password combination to open

Security Assurance Function
When someone is inside the house, authorization for entry from the outside will be prohibited.

Built-in Fire Detection
Generates alarm in case of a fire

Security Function
Prevents intrusion from the outside

Safety Cautions

This section contains important information to ensure the user's safety and prevent potential damage to property. Please, read Warning this section carefully and use the product accordingly.

• The user shall not install or repair the product without authorization.
• Do not install the product in the place where the gap between the door and the frame is 5mm or more.
• Make sure that no unauthorized person has the access to the password.
• Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged.
• Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product.
• Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.
• Please do not hang on the product or pull it.
• Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-).
• Replace all batteries immediately after they run out of power, and never mix new batteries with used ones.
• Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction.
• Replace the batteries within 1 week after the battery replacement alarm sounds.

Product Components

The product components used may vary depending on the installation environment.

Key Tag (For B2C Only)
User Manual, Product Warranty
'AA' Batteries (LR6)
Emergency Key(5EA)

Handle Shaft Spring
Handle Shaft, Installation Screws
Installation Manual(For B2C Only)

Outer Body Parts

Inner Body Parts

Mortise

SHS-AML320

SHS-AML220

Menu Table

Initialization

Registration

Deletion

Other function

Opening the Door from Outside with a Password

When purchased, the product is set to Multi-leveled Security Code Entry Mode initially. Please refer to "Multi-leveled Security Code Entry Mode setting" for Common Mode setting.

※ Silent Mode
Before entering the password, press the [ ] button and enter the password, then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.

Touching [Number Pad] will light up the number pad.

When two arbitrary buttons are lighted, press the buttons in order.

When the numbers on the number pad are lighted, enter the password and press the [ ] button.

• If the security mode is changed as 'common mode', second step will be skipped.

Note

• Password must be entered after the light is on, and if does not, touch [Number Pad] and re-enter.
• To cancel, press [ ]
• If the password is wrong 5 times, "peep" warning alarm will sound 20 times and the system will shut-down for about 3 minutes. When malfunction happens, "beep" will sound every 10 seconds, and stop mode will be turned off automatically after 3 minutes with multiple 'beeps'.

Opening the Door from Outside with a Card or Key Tag

The door can be opened from outside using a card or key tag. Place the registered card or key tag on the card reader.

Placing the Card or Key Tag on the Card Reader

Success:
DING DONG DENG
Fail:
DING DONG DING DONG

Place the card or key tag on the card reader.
The door will be opened after 1 second.

Opening the Door from the Inside

Opening by Pulling the Inner Handle

• Please be careful not to trap your hand during use.

Closing the Door from the Inside

Automatic Locking Setting
The door is automatically locked 1 seconds after the door is closed.

Manual Locking Setting
The door is locked when the [Close] button is pressed.

Note

• To check if the door is locked from the inside, press the security button briefly; the red LED will flash if the door is locked and the blue LED will blink if the door is unlocked.

Initialization (Password, Card, Key Tag)

All registered data (password, card, key tag) are deleted. After initialization, the password is set to '1234', and the registered card, key tag data are erased. Please register a new password after initialization.

1. Pressing the [Register] Button (from the inside)
   
   Press and hold the [Register] button for 5 seconds.
2. Entering the Numbers for Initialization (from the outside)
   
   When the number pad is lighted, enter '4560852580' and then press the [ ] button.

Password Change

The password can be 4~12 digits number. Only one password can be registered.

1. Pressing the [Register] Button (from the inside)
   
   Press the [Register] button briefly.
2. Entering the Current Password (from the outside)
   
   Enter the current password when the number pad is lighted, and press the [ ] button.
3. Entering a New Password (from the outside)
   
   Enter the new password (4 to 12 digits) and press the [ ] button.
4. Checking New Password Operation (from the outside)
   
   To make sure the password has been properly registered, check the new password and close the door.

• Manage your password with care so that unauthorized people will not have access to it. Regularly changing your password can reduce the risk of it being leaked.

Card and Key Tag Registration

Up to 30 cards, including the key tag and user password, can be registered. (Only ISO14443 A Type is available.)

1. Pressing the [Register] Button (from the inside)
   
   Open the battery cover of the inner body and briefly press the [Register] button.
2. Entering the Password (from the outside)
   
   Enter the password when the number pad is lighted, and press the [ ] button.

Card and Key Tag Registration Without ID number

3. Placing the Card or Key Tag on the Card Reader (from the outside)
   
   Place the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when "DING DONG DENG" sounds.
4. Confirming Card or Key Tag Registration (from the outside)
   
   Place the registered card or key tag to the card reader on the outer body.

• To register multiple cards or key tags, lightly place another card or key tag to the card reader within 20 seconds after registering the previous card or key tag.
• ID number is given automatically in order of the registration.

Card and user password registration with ID number

3. Enter 2 digits ID number
   
   Input ID between 01 and 30, and press [ ].
4. Enter new user password
   
   Enter new user password(4 to 12 digits) and press [ ].
   or

4. Placing the Card or Key Tag on the Card Reader (from the outside)
   
   Place the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when "DING DONG DENG" sounds.
5. Confirming Card or Key Tag Registration (from the outside)
   
   Place the registered card or key tag to the card reader on the outer body.

• User password is only for the user, so other functions such as registering cards are not available with this password.
• One ID has only one password or card.

Deleting Registered Cards

You can delete individual or all registered cards.

1. Pressing the [Register] Button (from the inside)
   
   Press the [Registration] button for 3 seconds.
2. Entering the Current Password (from the outside)
   
   Enter the current password when the number pad is lighted, and press [ ] button.

Deleting Cards

3. Reading the card to be deleted
   
   If you want to delete all cards data, press [88] + [ ] after step 2.

Deleting ID information

3. Enter ID number to delete
   
   Enter 2 digits ID number, then the card or user password of it will be deleted.

Double Authorization Mode Setting

Double authorization mode requires both card and password to open the door, ensuring more security.
To setup the double authorization mode, more than 1 card must be registered.

Briefly press the [Register] button on the inner body.

Press the [ ] button after pressing the [4] or [6] button, and the authorization mode will be set.

Two-factor Authentication Mode Operation

1. Touching [Number Pad].
   
2. Enter the password when the number pad is lighted, and press the [ ] button.
   
3. Touch the card on to the [Card Reader], if the authentication is successful, the door will open.
   

Multi-leveled Security Code Entry Mode Setting

You can set the security mode suitable for your use when you open the door using a password.

Briefly press the [Register] button on the inner body.

Press the [ ] button after pressing the [7] or [9] button, and the security mode will be set.

Setting the Security Function

This is a function to prevent any intrusion while you are out. Should the door be opened from the inside while the intrusion prevention function is on, the emergency alert light will flash and the alarm will make "beep beep beep~" sound.

Setting the Security Function

1. When the door is closed [ ] of the outside body's number pad will light up.
2. Press and hold the [ ] button on the outer body for 3 seconds while the door is locked.

Releasing the Security Function

Apply the registered card or key tag to the card reader, or enter the password and then press the [ ] button.

Security Assurance Mode Activation/Deactivation

At-home security mode is to prevent opening of the door from outside while someone is inside.

Security Assurance Mode Activation

While the door is locked, press [Security Assurance] button on the inner body part for 3 seconds.

Security Assurance Mode Deactivation

Pull the inner body handle to open the door, and it will deactivate.

Security Assurance Mode Operation

Inside: Press the [Security Assurance] button, then the sound for action-unavailable willbe heard.
Outside: Press the [Number Pad] or touch with a card, then the sound for action-unavailable will be heard.

• When the security assurance function is activated, the door cannot be unlocked from the outside, so please be careful. Be especially careful not to allow children to set this mode accidently from the inside.

Sound Setting and Releasing

The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the user's preference. The product is set to generate all sounds at the factory.

Open the battery cover on the inner body.

[0]: Mute [1]: Normal [2]: Loud

Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.

Door Lock Time Setup Function

This function sets the time interval between the moment the door open/closed sensor recognizes the door as closed and the moment deadbolt locks the door. It can be prevented the deadbolt jam problem by adjusting the time.

Press [Registration] button briefly.

Press [51] ~ [59] button, and then press [ ] button.

Welcome Function On/Off

The welcome function is a convenient function that automatically activates the authorization standby mode when a user approaches the door, even before touching the number pad.

Open the battery cover and press [Registration] button briefly.

Code	Welcome	One-minute alarm
[1]+[ ]	ON	ON
[2]+[ ]	ON	OFF
[3]+[ ]	OFF	OFF

On and Off / Function Description

• Welcome function: The mode will automatically activate the authorization standby mode when a user approaches the door lock.
• One-minute alarm: When someone remains in frontof the door lock for more than a minute, this mode will sound the tamper prevention alarm.

• The factory defaults are set with the welcome function on and the alarm function off.
• The working distance of the infrared sensor can differ depending on light conditions and other environments. When the front door is exposed to sun light or constant bright lights it is advised to limit the usage of the sensor as it might sound the alarm.

Automatic/Manual Locking Setting

The Automatic Locking mode allows for automatic locking of the door when it is closed.

Open the battery cover on the inner body.

Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the 'A'/'M' position.

• Automatic: The door is automatically locked 2 seconds after being closed.
• Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.

Using the Emergency Battery

If the batteries are not replaced after their replacement time comes, they will be completely discharged and the lock will not operate.

Opening the Door Using an Emergency Battery
Purchase an emergency battery (9V) at the nearest store.

• As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.

Place the card or key tag on the card reader, or enter the password, while the 9V battery is connected to the external power port of the outer body.

Replacing the Batteries

Battery Replacement Alarm Generation

If the melody of "Blues for Elise" sounds when opening the door with the password or a card (key tag), it is time to replace the batteries.
(The low battery indicator is lighted when the melody sounds.)

Replacing the Battery

Replace all 8 batteries within a 1 week of the first alarm sound.

• The unit will stop operating suddenly if the batteries are not replaced.

• Depending on battery manufacturer, date of manufacture and the user environment, the duration of use may vary.
  (In the case of average use, given as 10 times a day, 8 AA alkaline 1.5Vbatteries can last for 12 months.)
• If the poles of the batteries are not placed properly, the lock will not operate normally.
• Liquid leaks from batteries can damage the product. Check the batteries regularly (every 6 months).
• After the battery replacement alarm has sounded, password/card information cannot be registered, changed, deleted, initialized or configured until the batteries are replaced.

Intrusion Detection Function

This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside.
(This is a basic function of the lock, and cannot be separately set or released.)
If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.

Alarm Sound (Prank Prevention Function)

This function generates an alarm sound and deactivates lock operation when it is improperly handled from the outside.

This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong password is entered five times in a row.
The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single "DING" sound is generated every 10 seconds and seven consecutive "DINGS" will sound after 3 minutes. Following this, the lock is released from inactive mode.)

Releasing the Alarm

Inside	Press the [Register] button.
Outside	Apply the registered card or key tag to the card reader, or enter the password and then press the [ ] button.

Built-in Fire Detection Function

This function generates the alarm sound when fire is detected so that the residence can quickly respond. The built-in fire detection function is a basic function of the lock, and cannot be released by the user.
Fire detection function is operational at about 75 ℃ ± 10 ℃; this can vary depending on the installation environment.
When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound.
The door is automatically opened after the alarm sound has stopped.
(The lock resumes normal operation if the inside temperature returns to a normal level.)
The built-in fire detection function is activated when the temperature rises around 60°C, which may differ depending on the installation environment.

Product Specifications

Item	Specifications
Voltage	AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V)
Emergency Power Source	9V Battery (6LF22) (Separately sold)
Operation Method	Electronic Control Method (Password entry or card or key tag reading)
Weight	3.9 kg (including both inner and outer bodies)
Product Dimensions	Outer Body (including the handle)	85mm(W) × 346.5mm(H) × 61mm(D)
	Inner Body (including the handle)	86mm(W) × 354.8mm(H) × 63 mm(D)

• The contents of this user guide are subject to change without prior notice to the user in order to enhance performance of the product.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Samsung SHS-P717 - Door Lock Manual