Samsung SHS-H625 User Manual

Safety Cautions
Warning
SHS-H625
• The user shall not install or repair the
product without authorization.
• Do not install the product in the place
where the gap between the door and the
frame is 5mm or more.
• Make sure that no unauthorized person
has the access to the password.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or
the product may malfunction or be
damaged.
• Do not use the excessive force or sharp
objects to push the lockbuttons, as this
can damage the product.
Convenient Opening
• Make sure that the door is completely
- User friendly access with
closed when going outside. The
cards and password
manufacturer does not assume the
Graphic Interface
- Shows the operation status
of the doorlock
Product Components
Double Authorization
- Requires card & password
combination to open
The product components used may vary depending on the installation
Double Locking
environment.
- Prevents opening from outside
(Do not disturb)
Built-in Fire Detection
- Generates alarm in case of a fire
Security Function
- Prevents intrusion from the outside
Outer Body
Key Tag
Key tail
User Manual
'AA' Batteries (LR6)
Emergency Key (5EA)
www.sds.samsung.com
GC68-02069A ED:03
Opening the Door from Outside with a Password Opening the Door from the Inside
When purchased, the product is set to Multi-leveled Security Code Entry Mode Pulling down the Door Lock Handle
initially. Please refer to "Multi-leveled Security Code Entry Mode setting" for
Common Mode setting.
1. Multi-leveled Security Code Entry Mode
Success: Too~~~t
Fail: Toot
Rotate the door lock handle of the inner
Touching [Number When two arbitrary When the numbers on the body downward.
Pad] will light up the buttons are lighted, number pad are lighted,
number pad. press the buttons in enter the password and
order.
press the [] button.
Closing the Door from the Outside
2. Common Mode
Touch [Number Pad]
Success: Too~~~t
Fail: Toot
Touching [Number Pad] will Enter the password when the
light up the number pad. number pad is lighted, and press
the [] button.
●
Password must be entered after the light is on, and if does not, touch
[Number Pad] and re-enter.
Note
● To cancel, press [ ] button and re-enter.
Closing the Door from the Inside
● If the password is wrong 5 times, "Toot~, Toot~, Toot~" warning alarm will
sound 20 times and the system will shut-down for about 3 minutes. When
malfunction happens, "Toot" will sound every 10 seconds, and stop mode will
be turned off automatically after 3 minutes with multiple 'beeps'. Closing the Door from the Inside
Opening the Door from Outside with a Card or
Key Tag
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Placing the Card or Key Tag on the Card Reader
SHS-AML320
The door is automatically locked
2 seconds after the door is closed.
CARD Success: Too~~~t
Fail: Toot
Place the card or key tag on the card reader.
The door will be opened after 1 second.
4
Outer Body Parts
This section contains important information to ensure the user's
Number Pad Unlighted
safety and prevent potential damage to property. Please, read
this section carefully and use the product accordingly.
responsibility for any harm caused
by engagement of the lock on an
improperly closed door.
• Please do not hang on the product or
pull it.
• Be sure to correctly match the poles
(+/-) when installing the batteries. Install
the batteries with the correct poles (+/-).
• Replace all batteries immediately after
they run out of power, and never mix
new batteries with used ones.
• Do not use water, benzene or alcohol
when cleaning the product, as these
fluids can cause product malfunction.
• Replace the batteries within 1 week
Inner Body Parts
after the battery replacement alarm
sounds.
Battery Cover
Registration
Button
Inner body
Mortise Strike Handle
(SHS-AML320)
Or
Mortise
Mortise Strike Strike
(SHS-AML220) box
Inner Body
Handle Shaft • Inner Fastening Bolts
Handle Shaft Spring • Strike Fastening Bolts
• Support Panel and Inner
Body Fastening Bolts
• Support Panel and Outer
Body Fastening Bolts
2 SHS-AML320
Initialization (Password, Card, Key Tag)
Rotating the Manual Open/Close All registered data (password, card, key tag) are deleted. After initialization, the
password is set to '1234', and the registered card, key tag data are erased.
Lever to the Right or Left
Please register a new password after initialization.
Too~~~t
1. Pressing the [Register] Button
(from the inside)
Toot→ Toot, toot
→ Toot, toot, toot, toot
Rotate the manual Open/Close lever
to the right or left to lock the door or
release the locking.
Press and hold the [Register] button
for 5 seconds.
Password Change
The password can be 4~12 digits number. Only one password can be registered.
If you go outside while in manual locking mode,
1. Pressing the [Register] Button
touch [Number Pad] on the outer body.
(from the inside)
Open the battery cover of the inner
body and briefly press the [Register]
In the Manual Locking Mode
button.
3. Entering a New Password
(from the outside)
SHS-AML220
Enter the new password (4 to 12 digits)
and press the [] button.
The door is locked when the [Close]
- To prevent burglary, it is recommended
button is pressed, or the manual Open/
to use a password of 6 digits or longer.
Close lever is rotated.
(Only numbers between 0 and 9 can
be used.)
5
5. Checking New Password Operation (from the outside)
Number Pad Lighted
Too~~~t
Number Pad
● Manage your password with care so that unauthorized people will not have
access to it. Regularly changing your password can reduce the risk of it
being leaked.
Warning
● A registered password cannot be deleted. Change the password to a new
Card Reader one or initialize it to delete all registered data (password, card and key tag)
and then reregister them.
Outer Body Handle Card and Key Tag Registration
Up to 20 cards, including the key tag, can be registered.
Emergency
(Only ISO14443 A Type is available.)
Keyhole
External Power 1. Pressing the [Register]
Contact
Button (from the inside)
Toot
Open the battery cover of the
inner body and briefly press the
Sound Control
[Register] button.
Switch
Auto/Manual
Locking Switch
3. Placing the Card or Key Tag
CLOSE Button
on the Card Reader (from the
Manual Open-
outside)
and close
Lever
Too~~~t
CARD
Place the card or key tag to be
registered on the card reader of the
outer body. You will know the card or
key tag has been registered when
"Too~~~t" sounds.
● To register multiple cards or key tags, lightly place another card or key tag
to the card reader within 20 seconds after registering the previous card or
Deadbolt
Warning
key tag.
Latch bolt
Open-door sensor
3
SHS-AML220
● Please be cautious when using this function, since the door can only be
opened from the outside using the emergency key when this function
Warning is set. Please be particularly careful of children accidentally setting this
function from the inside.
Automatic/Manual Locking Setting
2. Entering the Numbers for
Initialization (from the outside)
The Automatic Locking mode allows for automatic locking of the door
when it is closed.
Set the [Automatic/Manual Locking] toggle switch of
the Inner Body to the 'A'/'M' position.
When the number pad is lighted, enter - Automatic: The door is automatically locked 2 seconds after being closed.
'4560852580' and then press the [] button. - Manual: The door does not lock automatically, and [CLOSE] button must be
- Success: Too~~~t pressed from the inside, touch [Number Pad] to close the door.
- Fail: Toot
Sound Setting and Releasing
The sound that is generated when the number buttons are pressed, when the
door is locked or when the locked door is unlocked, can be set according to
the user's preference. The product is set to generate all sounds at the factory.
2. Entering the Current Password
(from the outside)
Toot Too~~~t
Open the battery cover on the
inner body.
- [ 0 ] Button: All sounds except the alarm sound are deactivated.
Enter the current password ('1234' after
- [1] and [2] Buttons: All sounds are activated and the sounds get bigger as the step
initialization) when the number pad is lighted,
become higher.
and press the [] button.
Alarm Sound (Prank Prevention Function)
4. Reentering a New Password
(from the outside)
This function generates an alarm sound and deactivates lock operation
when it is improperly handled from the outside.
Too~~~t Too~~~t
This alarm will sound if an attempt is made to open the door with an invalid card, or if
a wrong password is entered five times in a row.
The alarm sound is generated, and the lock is deactivated for 3 minutes. While the
door is in this inactive mode, a single "Toot" sound is generated every 10 seconds
and seven consecutive "Toot~, Toot~, Toot~" will sound after 3 minutes. Following
Enter the new password again to check if the this, the lock is released from inactive mode.)
new password is accurately configured, and
then press the [] button. Releasing the Alarm
Inside Press the [Register] button.
Outside Apply the registered card or key tag to the card reader, or enter
the password and then press the [
6
Deleting the Card or Key Tag
To make sure the password has been
● Registered cards cannot be individually deleted. All card information is
properly registered, check the new
deleted when the card delete function is selected. Previously registered
password and close the door.
Warning
cards cannot be used to open the locked door after they are deleted.
1. Pressing the [Register] 2. Entering the Password
Button (from the inside) (from the outside)
Toot→ Toot, toot
Open the battery cover of the Enter the password when the number
inner body and press and hold the pad is lighted, and press the [
[Register] button for 3 seconds. - Success: Too~~~t
- Fail: Toot
● Register a new card after deleting the card data.
● To open the locked door from outside after deleting card data, use the
2. Entering the Password
Note registered password.
(from the outside)
● Deleting the card or key tag is available while the door is open.
Too~~~t
Multi-leveled Security Code Entry Mode Setting
You can set the security mode suitable for your use when you open the
door using a password.
Enter the password when the
number pad is lighted, and
press the [ ] button.

Toot
4. Confirming Card or Key Tag
Registration (from the outside)
Briefly press the [Register] Press the [ ] button after pressing the

button on the inner body. [7] or [9] button, and the security mode
will be set.
CARD
Double Authorization Mode Setting
Place the registered card or key
tag to the card reader on the
Double authorization mode requires both card and password to open the
outer body.
door, ensuring more security.
Toot
Briefly press the [Register] Press the [

button on the inner body. [4] or [6] button, and the authorization
mode will be set.
7
Replacing the Batteries
Battery Replacement Alarm Generation
If the melody of "Blues for Elise" sounds when opening the door with the
password or a card (key tag), it is time to replace the batteries.
(The low battery indicator is lighted when the melody sounds.)
Replacing the Battery
Replace all 8 batteries within a 1 week of the first alarm sound.
8 AA batteries
● If the poles of the batteries are not placed properly, the lock will not
operate normally.
● Liquid leaks from batteries can damage the product. Check the batteries
Warning
regularly (every 6 months).
● After the battery replacement alarm has sounded, password/card
information cannot be registered, changed, deleted, initialized or
configured until the batteries are replaced.
● The unit will stop operating suddenly if the batteries are not replaced.
Using the Emergency Battery
Put the [Sound Control] switch on
one of [0], [1], or [2], and close the
If the batteries are not replaced after their replacement time comes, they will
battery cover.
be completely discharged and the lock will not operate.
Purchase an emergency battery (9V) at the nearest store.
- As the alkaline batteries offer longer life, they are recommended over the
manganese batteries or rechargeable ones.
Or
Place the card or key tag on the card reader, or enter the password, while
the 9V battery is connected to the external power port of the outer body.
] button.

10
●
The setup of double authorization mode only works when the door is open.
●
When purchased, the product is not set to double authorization mode initially.
● To setup the double authorization mode, more than 1 card must be registered.
Note
●
Double authorization mode will automatically be turned off when all cards are
deleted.
Setting the Security Function
Setting the Security Function
Too~~~t
1. When the door is closed [
of the outside body's number
pad will light up.
Too~~t
2. Press and hold the [
outer body for 3 seconds while the
 ] button. door is locked.
Releasing the Security Function
Apply the registered card or key tag to
the card reader, or enter the password
Or
CARD
and then press the [] button.
● The security function is automatically released when the locked door is
opened from outside by entering the registered password or applying the
Note
card or key tag to the card reader.
Setting the Double Locking
Too~~~t
The double locking function prevents opening of a locked door from outside.
[7] Button : Multi-leveled Security
Code Entry Mode
Setting Double Locking Releasing Double Locking
[9] Button : Common Mode
Too~~~t
Press the [Close] button for 2 The double locking function is released
seconds or longer from the inside when the inner body handle is rotated
while the door is locked. downward, or the manual Open/Close
lever is rotated to the right or left.
Activating Double Locking
Inside : The double locking sound is generated
Too~~~t
when the [Close] button is pressed.
Too~~t
[4] Button : Double authorization Outside : The double locking sound is
Too~~t
Or
mode on generated, the double locking display
[6] Button : Double authorization
LED is lighted, and the door cannot
mode off
be opened when touch [number pad],
] button after pressing the or a card is applied.
8
Intrusion Detection Function
This function generates the alarm sound when an attempt is made to
forcefully open the door from the inside or the outside.
(This is a basic function of the lock, and cannot be separately set or released.)
Built-in Fire Detection Function
This function generates the alarm sound when fire is detected so that the
residence can quickly respond. The built-in fire detection function is a basic
function of the lock, and cannot be released by the user.
When fire occurs, the temperature sensor detects it and flashes the [Close] button
while generating the alarm sound.
The door is automatically opened after the alarm sound has stopped.
(The lock resumes normal operation if the inside temperature returns to a normal
level.)
The built-in fire detection function is activated when the temperature rises around
60 , which may differ depending on the installation environment.
Product Specifications
Item Specifications
Voltage 8 AA Alkaline 1.5 Batteries (LR6) (6V)
Emergency
Power 9V Battery (6LF22) (Separately sold)
Source
Operation Electronic Control Method (Password entry or card or
Method key tag reading)
Weight 2.6Kg (including both inner and outer bodies)
Outer Body
(including 81.9 mm(W) x 302.4 mm(H) x 66.1 mm(D)
the handle)
Product
Dimensions
Inner Body
(including 79.0 mm(W) × 290.0 mm(H) × 80.3 mm(D)
the handle)
● The contents of this user guide are subject to change without prior notice
to the user in order to enhance performance of the product.
11
]
] button on the
9
12