Table of Contents
Advertisement
Quick Links
Instructions - Parts List
Sealant Gun
950 Series
100 psi (6.9 bar, 0.69 MPa) Maximum Working Pressure
Size
Palm Grip Gun
2.5 oz
C04074
6 oz
C04087
12 oz
Gun
Size
Assembly
2.5 oz
C04093
6 oz
C04093
12 oz
C04093
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001
Pistol Grip Gun
C04076
C04090
C04068
Palm Grip
+ Retainer
= Sealant Gun
C04077
C04074
C04091
C04087
C04069
309968 Rev.B
Handle
Pistol Grip
+ Assembly
+ Sealant Gun
C04079
C04076
C04079
C04090
C04079
C04068
Advertisement
Table of Contents
Related Manuals for Graco 950 Series
Summary of Contents for Graco 950 Series
- Page 1 + Sealant Gun 2.5 oz C04093 C04077 C04074 C04079 C04076 6 oz C04093 C04091 C04087 C04079 C04090 12 oz C04093 C04069 C04079 C04068 Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001...
-
Page 2: Warning Symbol
Check equipment daily. Repair or replace worn or damaged parts immediately. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your Graco distributor for information. • For professional use only. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. -
Page 3: Installation
Installation Installation Sealant Gun Tighten hose connections before operating equipment. The air-powered sealant gun can be supplied air from any standard air pump. Read this manual thoroughly before installing sealant gun. Do not exceed maximum working pressure of sealant gun. Inspect sealant gun for shipping damage. -
Page 4: Operation
Operation Air-Powered Sealant Guns Pressure Relief Procedure The 950 Series, air-powered sealant guns dispense This procedure describes how to relieve pressure for the adhesives or sealants from 2.5, 6 or 12 ounce sealant gun. To reduce the risk of serious injury, use this polyethylene cartridges. -
Page 5: Troubleshooting
Troubleshooting Troubleshooting Problem Cause(s) Solution(s) Gun fails to dispense when trigger is Material lodged in nozzle Follow Pressure Relief Procedure, actuated. page 4. Clear nozzle of blockage. Material supply, hose, passages, Check material supply settings, clogged hoses, etc. for proper material supply. Seal leakage Seals and packings are worn. - Page 6 Service Service Sealant Gun Body Disassembly (C04093) Sealant Gun Reassembly (C04093) This procedure describes how to disassemble the • Clean all parts thoroughly before reassem- sealant gun. Refer to Parts, Page 8. bling. Check them carefully for damage or wear, replacing parts if needed. 1.
- Page 7 Notes Notes 309968B...
-
Page 8: Technical Data
Parts Parts Technical Data Model C04093 Sealant Gun Body Assembly Category Data Maximum Working 100 psi (6.9 bar, 0.69 MPa) Pressure Part No. Description Outlet port size 1/4 npt(f) C04085 Knob and stud assembly C04072 Bracket Wetted parts Polyethylene C19221 Cotter pin Weight C04101 Body •... - Page 9 Parts Parts TI0439 309968B...
-
Page 10: Warranty
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written...