Page 1
Order No. MTV0501410CE Colour Television TX-29P800R-IRAN GP11 Chassis Specification Power Source AC SINGLE 220-240 V, 50/60 Hz 0-12 PAL B (AUST.) Power Consumption 176 W 1-9 PAL B (N.Z.) Standby condition 1-12 PAL/SECAM D Receiving System 21 Systems 1-12 NTSC M (JAPAN) Function 2-13 NTSC M (U.S.A.)
TX-29P800R-IRAN 1 SAFETY PRECAUTIONS 1.1. General Guide 1. It is advisable to insert an isolation transformer in the AC supply before servicing a hot chassis. 3. Measure the resistance value, with an ohmmeter, between the jumper AC plug and each exposed metallic cabinet part on the receiver, such as screw heads, aerials, connectors, control shafts, etc.
Page 4
TX-29P800R-IRAN 2. When using a picture tube test rig for service, ensure that the rig is capable of handling 32.0 kV without causing X- Radiation. Note: It is important to use an accurate periodically calibrated high voltage meter. 1. Set the brightness to minimum.
TX-29P800R-IRAN 3 MARKET MODE FUNCTION Outline: MPU controls the functions switching for each Ics through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Market Mode. 1. Selection of SERVICE 1 Mode Adjust the Volume “ZERO”...
TX-29P800R-IRAN 4 ADJUSTMENT PROCEDURE 4.1. Voltage Confirmation 4.2. E.H.T Check Item / preparation Item / preparation 1. Operate the TV set. 1. Receive an RF signal, window or crosshatch pattern. 2. Set controls : 2. Set the Brightness and Contrast to minimum (0 Beam) Brightness ...
TX-29P800R-IRAN 4.7. VRS Adjustment 1. PREPARATION a. Set DY to CRT not to tilt up and down and left and right deflection. (Fig. 11) b. Set CY to CRT and set CY magnet primarily. Pur Mg : Set Pur Mg that 2 magnets are vertical position.
TX-29P800R-IRAN so that all are aligned completely. SUB BRIGHT ..128 Adjustment 1. Select G-CUTOFF adjustment mode and collapse vertical scan. 2. Adjust G-CUTOFF control to become the DC=0V to video level at 180V as shown below. 3. Slowly turn the screen control clockwise until a green colour b.
TX-29P800R-IRAN 4.11. White Balance Item / preparation 1. Select Service Mode 1. 2. Aging should have been performed over 30 minutes. 3. Receive the white balance pattern: 4. Picture menu : DYNAMIC NORMAL. AI : OFF 5. Degauss the CRT face.
TX-29P800R-IRAN 4.13. Geomagnetic Item / preparation 1. Demagnetize the GM-Board around its perimeter with the Demagnetizer. 2. Set to control: Geomagnetic..Auto Adjustment procedure 1. Connect a DC voltage meter to TPGM1-2pin (GM-Board). 2. Adjust the R4863 (GM-Board) so that the Vx Out at TPGM1-2pin becomes 4.9 0.05 V.
TX-29P800R-IRAN 5 DEFLECTION ADJUSTMENT 5.1. V-Adjustment/Confirmation (4:3 Mode) 5.1.1. V-HOLD CONFIRMATION 1. Receive PAL monoscope pattern (E10) (UTF:E-5) (Middle and south america model:Colour dac=0) 2. Set scan mode to 100Hz by remote control. 3. Set aspect to 4:3 4. Confirm that V-hold is normal 5.
TX-29P800R-IRAN 3. Adjust V-AMP (100i / 4:3) so that B, D (Fig. 17) is 2.1± 0.1. 5.1.3.3. 50p V-AMP ADJUSTMENT 1. Receive PAL monoscope pattern (E10) (UTF:E-5) (Middle and south america model:Colour dac=0) 2. Set scan mode to progressive by remote control key.
TX-29P800R-IRAN 5.3. Pincushion Adjustment/Confirmation (4:3 Mode) 5.3.1. 75i SIDE PINCUSHION ADJUSTMENT (4:3 MODE) 1. Receive PAL cross-hatch pattern (E-5) (UTF:E-21) (Middle and south America/Philippine model (UTF:E-4) 2. Set scan mode to 75/8331 by remote control key. 3. Adjust Trapezoid (75i/4:3) and Parabola (75i/4:3) to make straight vertical line at both side.
Page 19
TX-29P800R-IRAN 5.3.3. 50p SIDE PINCUSHION ADJUSTMENT (4:3 MODE) 1. Receive PAL crosshatch pattern (E-5) (UTF:E-21) (Middle and south America/Philippine model (UTF:E-4) 2. Set scan mode to Progressive scan by remote control key. 3. Adjust Trapezoid (50p / 4:3) and Parabola (50p / 4:3) to make straight vertical line at both side.
TX-29P800R-IRAN 5.4. V Liniality Adjstment/Confirmation (4:3 Mode) 5.4.1. 75i V-Linear Adjustment 1. Receive PAL monoscope pattern (E10) (UTF:E-5) (Middle and south america model : Colour dac=0) 2. Set scan mode to 75/8331 by remote control key. 3. Confirm V-linear (75i / 4:3) as to the balance of circle.
TX-29P800R-IRAN 5.5. Deflection (16:9 Mode) Adjustment/Confirmation 5.5.1. DATA SETTING (16:9) 1. Copy the adjusted data of 100i/4:3 mode to 100i/16:9 in the table. 1 (Except V-S-Correct) 2. Copy the adjusted data of 75i / 4:3 mode to 75i / 16:9 in the table 1 (Except V-S-Correct).
TX-29P800R-IRAN 5.6. Deflection (16:9Mode) Adjustment/Confirmation 5.6.1. 100i SIDE PINCUSHION ADJUSTMENT (16:9 MODE) 1. Receive PAL croshatch pattern (E-5) (UTF:E-21) (Middle and south America/Philippine model (UTF:E-4)) 2. Set the aspect to 16:9 by remote control key. 3. Set scan mode to 100Hz by remote control key.
TX-29P800R-IRAN side. 3. Confirm there is no H-parallel distortion. In case of distortion is visible, adjust H-Parallel (50p(625p)/16:9) to make vertical line has no tilt at centre. Repeat 3) so that there is no Trapezoid/H-Pararell distortion. 4. Confirm the vertical pincushion at top/bottom corner.
Page 24
TX-29P800R-IRAN 5.7.3. V-HEIGHT ADJUSTMENT 1. 4:3 MODELS Adjust V-Amp(1125i_50) so that A,B in Fig 23. is *1. 29” 5.5cm ± 1cm 34” 7.0cm ± 1cm 2. WIDE models Adjust V-Amp(1125i_50) so that C=90 ± 2.5(%) in the Fig.25 5.7.4. H-CENTER ADJUSTMENT 1.
TX-29P800R-IRAN 9.1. Replacement Parts List Ref. Part No. Part Name & Description Remarks C1102 ECJ1VF1C104Z C 0.1UF, Z, 16V Ref. Part No. Part Name & Description Remarks C1104 EEEHB0J101P E 100UF, 6.3V C1105 EEEHB0G221P E 220UF, 4V A68LZU185X-D PICTURE TUBE...
Page 61
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1445 ECA0JM471B E 470UF, 6.3V C2452 ECA1VM101B E 100UF, 35V C1446 ECJ2VF1C104Z C 0.1UF, Z, 16V C2453 ECA1VM101B E 100UF, 35V C1448 ECA0JM222B E 2200UF, 6.3V...
Page 62
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C3089 ECJ1VF1A105Z C 1UF, Z, 10V C404 ECA1VM471B E 470UF, 35V C3093 ECJ2FF1E105Z E 1UF,Z, 25V C4040 ECJ1VB0J105K C 1UF, K,6.3V C3097 F1H1A1050028...
Page 63
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C4238 ECJ1VF1C104Z C 0.1UF, Z, 16V C4453 ECJ1VB0J105K C 1UF, K,6.3V C4242 ECJ1VF1A105Z C 1UF, Z, 10V C4455 ECJ1VB0J105K C 1UF, K,6.3V C4243 ECJ1VB0J105K C 1UF, K,6.3V...
Page 64
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C4574 ECJ1VB0J105K C 1UF, K,6.3V C4653 ECJ1VF1A105Z C 1UF, Z, 10V C4575 ECJ1VB1H103K C 0.01UF, K, 50V C4654 ECJ1VC1H040C C 4PF, D, 50V...
Page 65
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C764 ECA1CM471B E 470UF, 16V DIODES C7707 ECJ1VB1C104K C 0.1UF, K, 16V D001 MA3150HTX ZENER DIODE C772 ECA1HM100B E 10UF, 50V D002 MA3150HTX...
Page 66
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks D771 ERA15-02 DIODE IC4201 C1AB00001869 D772 MA4104J DIODE IC4202 C0CBCAC00095 IC, POWER SUPPLY D773 MA165 DIODE IC4203 C0CBCAD00012 IC, POWER SUPPLY D776 MA165...
Page 67
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks L2523 ELESN6R8KA PEAKING COIL L741 ELEKE101KA COIL L2524 ELESN6R8KA PEAKING COIL L743 EXCELSA35T BEAD CORE L2527 EXCELSA35T BEAD CORE L744 TALFP15B152K CHIP INDUCTOR COIL...
Page 68
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks Q4004 2SB709ATX TRANSISTOR R051 ERJ6GEYJ561 M 560OHM,J,1/10W Q4005 2SB709ATX TRANSISTOR R053 ERJ3GEYJ221 M 220OHM,J,1/16W Q4007 2SD0601A0L TRANSISTOR R054 ERJ6GEYJ472 M 4.7KOHM,J,1/10W Q4008 2SD0601A0L...
Page 69
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1202 ERJ3GEYJ103 M 10KOHM,J,1/16W R2401 ERJ3GEYJ103 M 10KOHM,J,1/16W R1203 ERJ3GEYJ103 M 10KOHM,J,1/16W R2402 ERJ3GEY0R00 M 0OHM,J,1/16W R1204 ERJ3GEYJ103 M 10KOHM,J,1/16W R2403 ERJ3GEY0R00 M 0OHM,J,1/16W...
Page 70
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R3038 ERJ8ENF75R0 M 75OHM, 1/8W R371 ERJ6ENF1801 M 1.8KOHM, 1/10W R3041 ERJ3GEYJ223 M 22KOHM,J,1/16W R372 ERJ6ENF1201 M 1.2KOHM, 1/10W R3043 ERJ3GEYJ223 M 22KOHM,J,1/16W...
Page 71
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R409 ERJ6GEYJ103 M 10KOHM,J,1/10W R4274 ERJ3GEYJ821 M 820OHM,J,1/16W R4090 ERJ6GEYJ331 M 330OHM,J,1/10W R4276 ERJ3EKF3601 F 3.6KOHM,F,1/16W R4092 ERJ6GEYJ471 M 470OHM,J,1/10W R4278 ERJ6GEYJ471 M 470OHM,J,1/10W...
Page 72
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R4441 ERJ3GEYJ471 M 470OHM,J,1/16W R4519 ERJ3GEYJ100 M 10OHM,J,1/16W R4442 ERJ3GEYJ222 M 2.2KOHM,J,1/16W R4520 ERJ3GEY0R00 M 0OHM,J,1/16W R4443 ERJ3GEY0R00 M 0OHM,J,1/16W R4521 D1HG5608A002 FIXED RESISTOR...
Page 73
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R4609 ERJ3GEY0R00 M 0OHM,J,1/16W R718 ERDS2TJ103 C 10KOHM,J, 1/4W R4610 ERJ3GEY0R00 M 0OHM,J,1/16W R719 ERDS2TJ222 C 2.2KOHM,J, 1/4W R4611 ERJ3GEY0R00 M 0OHM,J,1/16W R720...
Page 74
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R946 ERDS2TJ681 C 680OHM,J, 1/4W FL4422 TLK20LFA103M EMI FILTER R947 ERJ6GEY0R00 M 0OHM,J,1/10W FL4423 TLK20LFA103M EMI FILTER R948 ERJ6GEY0R00 M 0OHM,J,1/10W FL4424 TLK20LFA103M...
Page 75
TX-29P800R-IRAN Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks JS1105 ERJ3GEY0R00 M 0OHM,J,1/16W SW1004A EVQ11G05R SWITCH JS1124 ERJ3GEY0R00 M 0OHM,J,1/16W SW1005A EVQ11G05R SWITCH JS1125 ERJ3GEY0R00 M 0OHM,J,1/16W SW1006A EVQ11G05R SWITCH JS116 ERJ3GEY0R00...