WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided herein.
IMPORTANT NOTICE User's Guide Contents: Install Autodesk DWF Viewer Internet Explorer Settings Operating Environment Functions Provided on Each Drawing Page Using with Network Install Autodesk DWF Viewer Autodesk DWF Viewer is necessary to view drawings and to activate the functions of this system. Please download and install.
Page 4
2. Internet Explorer setting [Tools] - [Internet Options] for Internet Explorer 7...
Operating Environment : Pentium III or higher recommended Monitor : 1024 x 768 or higher resolution recommended Mouse : A mouse with wheel recommended : Microsoft Windows 2000 SP4 / XP / Vista Browser Microsoft Internet Explorer 6.0 / 7.0 Drawing viewer : Autodesk DWF Viewer 6.0 / 7.0 * Use the software following respective license terms and conditions.
Page 7
Layer Display Changing Function When any of the color buttons on the toolbar is clicked, it can be selected to display desired layer in its color or not to display each layer. This allows you to see the pattern layer only by setting other layers to "non display".
Page 8
4. Move the ZEUS Engine Program of step 2 to the folder created at step 3 in the Server. 5. Detach the ZEUS Service Manual Ver.2 to the folder created at step 3 in the Server. 6. Unzip the ZEUS Service Manual Ver.2 within the folder in the Server. Example of folder Procedure of File-Path The zeusFPch is the exclusive program to exchange the file-path names written in both source files of ZEUS...
Page 9
1. Whenever changing the file-path of both ZEUS Engine Program and ZEUS Service Manual to use with network, pay the attention to set the "Exchange to" column that should have a proper relation between ZEUS Engine Program and ZEUS Service Manual with referring the following. Run the zeusFPch and set "Exchange to"...
Page 10
2. Run the zeusFPch to change the path in the ZEUS Engine Program Ver.2. 3. Set ZEUS Engine Program in the created folder in the server to the "Target Folder", and then press "START". (This procedure is one time only)
Page 11
4. Run the ZeusFPch to change the path in the ZEUS Service Manual Ver2. 5. Set unzipped ZEUS Service Manual in the created folder in the server to the "Target Folder", and then press "START". (This procedure is required whenever placing service manual.) Confirmation Confirm that service manual on the server can be operated normally by client PC.
Page 12
Through WEB, ver. 6.5 has been released but with it, the linking function in this manual may not work properly. If ver. 6.5 has been installed, uninstall it and reinstall ver. 6.0. To get ver. 6.0, click the icon, or contact to the nearest Toshiba Service Centre for further assistance. Freezing windows opened (Cannot close the open windows) This may happen occasionally.
Page 13
Continue to use by operating the windows. Precaution when opening the diagrams While opening the diagrams, the menu in the left frame changes its color to GRAY. This is an indication that the viewer is processing. With this condition, the menu indication color may stick to the GRAY color or Windows may freeze if clicking other menu.
Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING: This product is manufactured using lead free solder.
SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 17
inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
Page 18
Resistance values in orms (Ω). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : 1 MΩ Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its supplements;...
SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 21
3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 22
6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 23
10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity.
SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 28
= Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassis ground, using a color bar signal with all controls at normal, line voltage at nominal AC volts. 5.
ADJUSTMENT Service Mode Entering to Service Mode 1. Press button once on remote control. ↓ 2. Press button again and hold button down. ↓ Service Mode display 3. While holding the button, press MENU button on TV set.
Page 176
Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC.
Test signal selection PROGRAMME (on TV or remote control) Selection of the adjustment items Volume +/- (on TV or remote control) Change of the data value Adjustment menu mode ON/OFF MENU button (on TV) "i+" + PROGRAMME button on TV Initialization of the memory (IC510) Reset the count of operating "i+"...
Page 178
Item Name of adjustment Address RCUT RED CUT GCUT GREEN CUT BCUT BLUE CUT RDRV RED DRIVE GDRV GREEN DRIVE BDRV BLUE DRIVE BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX CONTRAST MAX OPT1 TV SET OPTION 1 00F1 OPT2 TV SET OPTION 2 00F2...
Page 179
Enter to service mode and select menu of TVOP by pressing P or P during display of adjustment menu. After selecting TVOP, press + or - to set I2C check function to disable or enable as below. TVOP FUNCTION DESCRIPTION 0 (Normal) D5 (bit5) I2C check between TV-Micro and Standby-Micro (WDT) Disable Enable Setting Panel Option Data...
Page 180
Convert from Bit (Binary) to Hex The table for converting from bit (D7-D0) to hex (0x**). BIT (Binary) High nibble Low nibble E.g. If Bit D7-0 = 0101 1010, Hex data is 0x5A.
For example, if want to initialize 42ZV635D, change MODEL ID into "0x18". Note: MODEL ID is hex value. For example, set value for 42ZV635D is not Decimal 18 but hex 18. 4) Change PANEL OPTION data into OPT4 to initialize by pressing...
Perform "Auto tune" on the owner's manual. MODEL ID TABLE MODEL ID (HEX) Model name Panel vendor OPT4 Data (HEX) 0x18 42ZV625D/ZV635D LGD 0x17 0x19 47ZV625D/ZV635D LGD 0x18 0x1A 55ZV625D/ZV635D LGD 0x1C Initializing Data setting flowchart after replacing the Signal Unit Test Signal Selection Every pressing of button on the remote control changes the built-in test patterns on...
Picture Signal Red raster Green raster Blue raster All Black All White Self Diagnostic Function 1. Press "9" button on remote control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC's is executed properly. 2.
Page 184
TV CPU SW Version: Version information of TV Micro SW: Display 1 byte data. (Hex) EEPROM Version: Version information of TV Micro EEPROM: Display 1 byte data. (Hex) Power On Time: Total time the TV has been powered on. (Unit: Hours) (Decimal) Main PLL: Displays Data 11 - Data 18 (8 bytes) of tuner control data.
Page 185
Bus Errors: "none" is normal. Block: (SCART (FULL)) (SCART (S+AV)) (Component/Composite) HDMI1 HDMI2 HDMI3 HDMI4 DTV (Digital Only) Version Check Mode 1. Press "9" button twice on remote control during display of adjustment menu in the service mode. 2. During Version Check, the following displays are shown. * Version check displays and items are subject to the models.
Page 186
TV Model TV Model ID Boot Code Version Core SW Version Seine SW Version TV Micro SW Version: Version information of TV Micro SW: Display 1 byte data. TV Micro EEPROM Version: Version information of EEPROM: Display 1 byte data. EDID Checksum: Pass/Fail Result Listed for HDMI 1-4 (left to right) Global Data Version...
--OK : A/D adjustment set correctly. --NG : A/D adjustment set incorrect. : A/D adjustment is not needed because the picture format is not used. Setting Hotel Mode Enter to service mode and select Hotel Mode menu by pressing P or P .
Page 188
D1 to D7) (Normal) VOLUX Set VOLUX as following. 1) Set speaker volume to 100. (Any value is OK, but 100 is better to check sound level.) 2) Down value of VOLUX until finding suitable sound volume level. VOLUX FUNCTION DESCRIPTION 0 (Normal) D7 (bit7) ~ Max Limiter of Volume Control...
OPT8 FUNCTION DESCRIPTION 0 (Normal) D7 (bit7) Hotel Mode RS232C Enable Disable D6 (bit6) ~ No use D4 (bit4) D3 (bit3) RF tuning operation by position up/down on Disable Enable remote or front panel of the TV set, number, and previous key when HDMI or PC input D2 (bit2) Enable mode that picture mode will be set in Enable...
Page 190
1 PowerOn/Standby LED: BUS Error Turn OFF the TV and unplug the power Green blinks continuously. cord. Other LEDs: OFF. Plug the power cord in again and turn ON the TV. 2 PowerOn/Standby LED: Power Protect Turn OFF the TV and unplug the power Red blinks continuously.
Page 191
6. When the update is complete, the following message is displayed. 7. Disconnect the USB drive. 8. The TV set is automatically turned off and then on. DTV Software Update - from Boot Up 1. Extract the update files onto a USB drive. 2.
PANEL IDENTIFICATION Panel Identification If the several panels are alternatively used in the same model without amending the model name, the identification marking will be shown at the last digit of the set serial number on the specification label on the back cover. In servicing, do not alter the panel because several setting and parts are different.
Page 196
DISMANTLING PRECAUTION Dismantling Precaution Strict control is required for screw type fixing Back Cover attachment. Alternative use may cause the damages to the Cabinet, Frame, or PC Boards due to over length. Use the correct screw that was put off from the each screw hole. Do not alter screws for the Back Cover attachment.
PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" "PRODUCT SAFETY NOTICE". CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 198
: Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted.
Page 199
PARTS LIST ↓Select Block : Search 1 / 1 Jump Page : Jump Location : Search Parts No. :...
FUNCTION AND OPERATION Tuning the Television for the First Time Before switching on the television, put your decoder and media recorder, if applicable, to Standby. To set up the television, use the buttons on the remote control.