Download Print this page

Operation - Sealey PDM10B Manual

710w bench pillar drill with digital display & laser guide

Advertisement

6. OPERATION

6.1.
OPERATION OF THE DISPLAY (fig. 4)
6.1.1.
Switching the display on/off: Press the button one for five seconds until the display (9) switches on or off.
6.2.
DISPLAY OF DRILLING DEPTH / SPEED
6.2.1.
The display can be switched between displaying the speed and the drilling depth by pressing (F) button.
6.3.
SETTING THE ZERO POINT
6.3.1.
The zero point for the drilling depth can be set by pressing the (G) button.
6.4.
SWITCHING THE LASER CROSS ON / OFF
6.4.1.
The laser cross can be switched on or off by pressing the (H) button.
6.5.
SWITCHING THE LED ON/OFF
6.5.1.
The LED work light can be switched on or off by pressing the (I) button.
fig.4
6.6.
HEIGHT ADJUSTMENT (fig.1)
6.6.1.
The position of the machine head can be adjusted to suit the work piece by height or length.
6.6.2.
Hold the handle (8) firmly.
6.6.3.
Release the clamping (5) lever for the height adjustment.
6.6.4.
Set the position of the machine head with the handle (8).
6.6.5.
Secure the position of the machine head with the clamping lever for height adjustment (5).
NOTE: Ensure in the lowest machine head position that the machine head will not be moved beyond the marking. Use the clamping
lever for height adjustment (5) to secure the machine head in this position. Otherwise, the guide could be damaged.
6.7.
SETTING THE DRILLING DEPTH (fig.1).
6.7.1.
The drilling depth can be set with the depth stop (7).
6.7.2.
Release the clamping lever on the depth stop (6).
6.7.3.
Carry out a test drilling. As soon as the desired depth is shown on the display (9) (refer to point 10.9), tighten the depth stop
clamping lever (6) again.
6.7.4.
The depth stop (7) is now locked in the desired drilling depth.
6.8.
CLAMPING/RELEASING DRILL BITS (fig 5 and fig 7)
6.8.1.
CLAMPING
6.8.2.
Hold the chuck in place and turn the securing ring (K) in the release direction.
6.8.3.
Turn the clamping sleeve (L) clockwise until the drill bit (M) can be inserted. Hold the holding ring (J) in place whilst doing so.
6.8.4.
Insert the drill bit (M), hold it in place and turn the clamping sleeve (L) counter clockwise by hand. Hold the holding ring (J) in place
whilst doing so.
6.8.5.
Hold the chuck in place and turn the securing ring (K) in the lock direction.
NOTE: When using small drill bits, set the chuck to roughly the right size for the drill bit beforehand. Otherwise, there is a risk of the
drill
bit not being properly centred in the chuck.
6.9.
RELEASING
6.9.1.
Turn the securing ring (K) in the "RELEASE" direction.
6.9.2.
Turn the clamping sleeve (L) clockwise until the drill bit (M) can be removed.
6.10.
ALIGNING WORK PIECES
6.10.1.
Switch on the laser cross via the display (9). See 6.1, Operation of the display.
6.10.2.
The intersection of the two laser lines exactly indicates the centre point of the drill.
6.10.3.
Align your marking on the work piece with the laser cross.
6.11.
CLAMPING THE WORK PIECE (fig. 6)
NOTE It must be possible to clamp the work piece securely. Do not work with work pieces that cannot be clamped securely. The cut
out of the quick clamp must be centrally aligned with the hole to be drilled. Otherwise, the drill bit or the chuck could be obstructed by
the quick clamp.
6.11.1.
Position the work piece with the help of the laser cross.
6.11.2.
Loosen the quick clamping lever (17).
6.11.3.
Place the quick clamp (2) on the work piece.
6.11.4.
Turn the quick clamp lever (17) clockwise to clamp the work piece. Turn the quick clamp lever (17) counter clockwise to release,
the quick clamp (2).
© Jack Sealey Limited
Original Language Version
fig.5
PDM10B Issue:2 (3)
06/03/23

Advertisement

loading