BEGA 84 875 Installation And Technical Information

Protection Class:

IP 65
BEGA
127.6 lbs

Weight:

Installation and Technical Information
BEGA
Installation and Technical Information

Tools Required:

5mm hex key
Tools Required:
Notice to Installer for 8945MH:
Adjustable wrench
4mm and 8mm Hex Key
1. 890B anchorage kit must be installed in concrete foundation.
Special tool (provided)
2. Anchorage kit 890B is buried below finished grade. Attention to alignment, leveling, and
location is required for proper installation.
890B anchorage installation:
1. Provide means to bring supply wiring to linear element in accordance with local code. The
UL listed, suitable for wet locations.
template has a 3-15/16" conduit hole for conduit entry. Provide adequate foundation
reinforcement for the intended load (by others).
Protection Class: IP65
Protection Class: IP 65
2. Use template and anchor bolts provided to assemble anchorage kit to be set. Make sure
anchor bolts do not protrude from lower concrete foundation more than 2-1/4" as shown.
Weight: 57.4 lbs
127.6 lbs
Weight:
3. Please refer to figure to establish location of lower concrete foundation. The anchorage kit
MUST BE buried. The top of the lower concrete foundation MUST be 5-3/4" BELOW finished
grade for proper installation. Position anchorage and level template properly.
Notice to Installer for 84 875:
4. Align and level anchorage kit so the corners of the square template are aligned with the
Notice to Installer for 8945MH:
1. Fixture may be damaged if connected to conduit systems that contain water - Article 300-
desired location and orientation of the corners of the square linear element. See figure.
5G of the National Electric Code requires that "Conduits or raceways through which
1. 890B anchorage kit must be installed in concrete foundation.
5. Install anchorage kit using either method: A. Attach template to forming and level properly.
moisture may contact energized live parts shall be sealed or plugged at either or both
2. Anchorage kit 890B is buried below finished grade. Attention to alignment, leveling, and
B. Insert anchorage kit into poured concrete. Concrete must be vibrated to ensure proper
ends." location is required for proper installation.
anchorage setting. Level template properly.
2. 79 803 anchorage kit must be installed in concrete foundation. Once anchorage is
890B anchorage installation:
installated, fixture cannot be reoriented!
8945MH installation:
3. The size of the foundation depends on the topgraphy, condition of soil and wind load.
1. Provide means to bring supply wiring to linear element in accordance with local code. The
1. Once the anchorage is set, remove template and hardware.
Foundation design must be determined by project structural engineer. template has a 3-15/16" conduit hole for conduit entry. Provide adequate foundation
2. Pull supply wiring to a length where splices can be seen and made through the access
reinforcement for the intended load (by others).
4. Anchorage top MUST be level or slightly above finished grade. Attention to alignment,
door.
2. Use template and anchor bolts provided to assemble anchorage kit to be set. Make sure
leveling, and location is required for proper installation.
3. Route supply wiring through the mounting base and install mounting base using hardware
anchor bolts do not protrude from lower concrete foundation more than 2-1/4" as shown.
5. Wet location listing does not imply suitability for exposure to standing water for long
provided. Complete finished grade. See figure.
3. Please refer to figure to establish location of lower concrete foundation. The anchorage kit
periods of time.
4. To insert lamp, loosen (4) M5 socket head screws on glass trim and remove glass and
MUST BE buried. The top of the lower concrete foundation MUST be 5-3/4" BELOW finished
6. LEDs are high-quality electronic components! Please avoid touching the light
reflector.
grade for proper installation. Position anchorage and level template properly.
output opening of the LED directly during installation.
5. Insert lamp(s) and replace reflector and glass trim.
4. Align and level anchorage kit so the corners of the square template are aligned with the
7. See page 3 for specific product safety warnings.
6. Use special tool provided to unlock the access door lock and remove access door. Route
desired location and orientation of the corners of the square linear element. See figure.
the luminaire wiring down and out the hand hold for connections to be made later.
5. Install anchorage kit using either method: A. Attach template to forming and level properly.
79 803 anchorage installation:
7. Loosen (8) M10 set screws at the base of the light element and place the light element over
B. Insert anchorage kit into poured concrete. Concrete must be vibrated to ensure proper
1. Provide means to bring supply wiring to linear element in accordance with local code. The
the mounting base. Tighten (8) M10 set screws to secure to base.
anchorage setting. Level template properly.
template has a 3-15/16" conduit hole for conduit entry. Provide adequate foundation
Make supply wiring and luminaire wiring connections inside the luminaire:
8.
reinforcement for the intended load (by others).
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
8945MH installation:
2. Use template and anchor bolts provided to assemble anchorage kit to be set. Make sure
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
1. Once the anchorage is set, remove template and hardware.
anchor bolts do not protrude from lower concrete foundation more than 2-1/4". GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
2. Pull supply wiring to a length where splices can be seen and made through the access
9. Replace access door and lock.
3. Refer to Figure 2 to establish location of lower concrete foundation. The anchorage kit
door.
MUST be buried. The top of the lower concrete foundation MUST be 5-3/4" BELOW
3. Route supply wiring through the mounting base and install mounting base using hardware
finished grade for proper installation. provided. Complete finished grade. See figure.
Relamping/Maintenance
4. To insert lamp, loosen (4) M5 socket head screws on glass trim and remove glass and
4. Align and level anchorage kit so that the corners of the square template are aligned with
reflector.
the same desired location and orientation as the corners of the square linear element.
Disassemble glass trim and glass. Clean dirt and
5. Insert lamp(s) and replace reflector and glass trim.
deposits from the luminaire and glass using only
5. Install anchorage kit using either method:
6. Use special tool provided to unlock the access door lock and remove access door. Route
solvent-free cleaners. Relamp and replace gasket if
A. Attach template to forming and level properly.
the luminaire wiring down and out the hand hold for connections to be made later.
damaged. Reassemble.
B. Insert anchorage kit into poured concrete. Concrete must be vibrated to ensure
7. Loosen (8) M10 set screws at the base of the light element and place the light element over
proper anchorage setting. Level template properly.
the mounting base. Tighten (8) M10 set screws to secure to base.
Lamp: (1) 150W T6 G12 MH
8. Make supply wiring and luminaire wiring connections inside the luminaire:
Philips :
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
Osram/Sylvania :
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
9. Replace access door and lock.
GE :
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
Relamping/Maintenance
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA/US 2004
Disassemble glass trim and glass. Clean dirt and
deposits from the luminaire and glass using only
Relamping/Maintenance
solvent-free cleaners. Relamp and replace gasket if
No relamping required.
damaged. Reassemble.
Lamp: (1) 150W T6 G12 MH
Philips : CDM150/T6
Osram/Sylvania : MC150T6/U/G12
Lamp:
46.8W LED module
GE : CMH150/T/U/G12
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA/US 2004
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018
CDM150/T6
MC150T6/U/G12
CMH150/T/U/G12
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
Anchorage Kit - included.
LED linear light building element
Linear element

Dimensions

Dimensions
A:
A: 8-5/8 "
B:
B: 177 "
C:
C:
Figure 1
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
Anchorage Kit - included. 890B
Replacement Parts
Description
Diffuser
Gasket
Lampholder
890B
Ballast (120/208/240/277V)
8945MH
- square
6-3/8 x 6-3/8 "
48-3/8 "
157-1/2 "
Figure 2
Replacement Parts
Description
Diffuser
Gasket
Lampholder
Ballast (120/208/240/277V)
Description
Lens
LED driver
LED module (3000K) (x12)
LED module (4000K) (x12)
9/14/2006
84 875
Part No
140533
830801
74121
75146
8945MH
Part No
9/14/2006
Part No
140533
830801
15000355.6
74121
76084-1400
75146
LED-0701/830
LED-0701/840
8945MH
84 875
4/27/2018
Page 1 of 4