Serial NO. Period 1 year N-BIOTEK provides a warranty on all parts and factory workmanship. The warranty includes areas of defective material and workmanship, provided such defect results from normal and proper use of the equipment. 1. The free warranty service will be provided once the unit is proved to be defective by wrong workmanship after NBIOTEK or reliable distributor’s examination.
When the smoke comes out from the product or smell something is burning or any other strange symptoms are occurred, pull out the power code and stop using it. (It can cause an electric shock and a fire.) OM-NB-206CXL / NB-206CXXL (Ver. 2020) 4/24...
When the movement of the product is required, please tie up the door and other movable part with a tape. ( Able to get an injury by opening door and get a damage of the product.) OM-NB-206CXL / NB-206CXXL (Ver. 2020) 5/24...
Please be sure to prevent foreign substances from getting into the sealing silicon of the door. (The inflow of open air can cause the change of temperature in chamber and discoloration of the packing part by a foreign substance.) OM-NB-206CXL / NB-206CXXL (Ver. 2020) 6/24...
If you don't have the outlet for AC 220V, then bury it under the ground after connecting the ground line to copper plate. * No ground connection can occur an electric shock, an electric leakage and a Fire. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 7/24...
Possible to maximize the available space through the Sticky Mat, and also able to attach various sizes of a holder. ● STAIN-RESISTANT INTERIOR This product is designed properly to a GMP facility, because it is never rusted through all-stainless composition. For Brief Introduction on UCC, visit our Youtube Channel https://www.youtube.com/user/NBIOTEK OM-NB-206CXL / NB-206CXXL (Ver. 2020) 8/24...
±1% Motor Plate Type B/L DC Motor Drive system Beltless Direct Drive Orbit diameter 25mm Platform size 520(W) x 520(D) mm Dimensions 465(W) x 540(D) x 125(H) mm Weight 323kg 393kg Power 110/220V, 50/60Hz OM-NB-206CXL / NB-206CXXL (Ver. 2020) 9/24...
CONTROL PANEL GLASS DOOR SLINDING SHAKER PLATFORM OUTER DOOR CASTER SPACE FOR HUMIDITY TRAY REAR VIEW (RPM RS232 PORT is optional with additional charge) Fuse CO₂ Gas Inlet Overheating Protection Power Outlet (Thermal Cut Off) OM-NB-206CXL / NB-206CXXL (Ver. 2020) 10/24...
Page 11
It is covered by the fan sealing of chamber so, it doesn’t have a danger of contamination and effect to the temperature of chamber. It can be turned on and off by its S/W under the Alarm S/W OM-NB-206CXL / NB-206CXXL (Ver. 2020) 11/24...
▶ Open #5(Master valve of cylinder) and #4(the regulator valve), #3 Flow meter. While Flow meter fully open, do adjust regulator valve at 1bar. The pressure gauge may be different depending on its manufacturing companies. If Regulator's pressure is too high, it causes malfunction of the CO₂ valve control. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 13/24...
For humidification in large chamber, water tray is placed on the bottom. Bottom heater warms up the water in the tray and it provides moisture naturally. Humidity is not controllable manually. Display only! OM-NB-206CXL / NB-206CXXL (Ver. 2020) 14/24...
Ex) If measured temperature is 38℃ and Display shows 37℃, then press up 1℃. Note * Calibration available range of temperature is ±5℃ * To go to next channel is to press “CAL/SET” button. After complete setup, the LED is back to temperature display. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 15/24...
Page 16
Ex) If measured CO2 value is 5% and Display shows 4%, then press up 1%. ☞ e. Fifth Click "CAL SET" Heating control * This is pre-programmed mode before releasing from manufacturer. Push UP (▲) and DOWN (▼) to set the value OM-NB-206CXL / NB-206CXXL (Ver. 2020) 16/24...
Page 17
When above stage is cleared, please press the CAL/SET button to save the new value. Please follow up the procedure for calibration below in case of discrepancy between actual values (measured by reliable thermometer or CO2 analyzer) in chamber and display. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 17/24...
In case that temperature is not able to heat up to set point, check this out. Once it is activated and cut the heater, the pilot lamp of it is lighted in red. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 18/24...
(You can check the shaker’s status through the “RUN” lamp on left top of the RPM/TIME display. When the shaker is not running, the pilot lamp is off. When the shaker is running the lamp flickers faster as RPM value.) OM-NB-206CXL / NB-206CXXL (Ver. 2020) 19/24...
Page 20
“STOP” button. since the product operates, but the operation will not stop until you The RPM range is 30 to 200RPM within maximum loading of flasks shown in table of load capacity below. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 20/24...
Page 21
※ This Maximum number of flasks is based on using sticky mat on all 3 shaker platform. ※ With maximum loading, shaking is available up to 150RPM. ※ In case of NB-206CXL, 2L Flask is only available in 3 compartment(lowest level).
Page 22
Pull out the shelf carefully NOTE: If you need to take the shelf out fully, unscrew thumb screw and bolt. #Photo1 #Photo2 While holding thumb screws with tool, unscrew the hexagon nuts with spanner or proper tools. OM-NB-206CXL / NB-206CXXL (Ver. 2020) 22/24...
If CO₂ deviation is still more than ±1% after 10 minutes alarm delay, audible alarm will ⚫ be activated again, unless pressing alarm mute. About 1 minute after the CO₂ is within ±1%, the alarm automatically stops. ⚫ OM-NB-206CXL / NB-206CXXL (Ver. 2020) 23/24...