Do you have a question about the N92 and is the answer not in the manual?
Questions and answers
Francisco Lopez ramos
April 20, 2025
Porque mi cámara no tiene señal, para **** el monitor
1 comments:
Mr. Anderson
May 10, 2025
The VEKOOTO N92 camera may have no signal for the monitor due to the following reasons:
1. The camera system is not receiving power (it requires 12–35V). 2. The power cable or wire connections are loose or incorrect. 3. The pins on the monitor cable or the 4-pin camera cable may be bent, broken, or misaligned.
Check all power and cable connections carefully and ensure they are secure and correctly connected.
This answer is automatically generated
Chris DeSalle
January 22, 2025
I’m trying to instal the N91 backup camera I have all the wires hooked up the red white and blue. Now on the large black aux wires there is a short red wire connected at each end what are those for? Do I need them hooked up to anything and if so where do I hook them up
1 comments:
Mr. Anderson
February 10, 2025
The short red wire on the large black auxiliary wires for the VEKOOTO N92 backup camera is the ACC wire. It should be connected to the car ignition wire ACC switch. This connection allows the device to start automatically when the car key is turned on and turn off automatically when the vehicle key is turned off.
Solar magnetic wireless backup camera 2.4ghz wi-fi & 9600mah battery (15 pages)
Summary of Contents for VEKOOTO N92
Page 1
Thank You for Buying VEKOOTO Product. Read This User Manual Before Installing and Using It. Pls keep this instruction or write down our email Vekooto@outlook.com So you can find us once you have any question. You are Always the First for us.
Let Vekooto be your eyes! ---VEKOOTO Monitor introduction The user can perform the manipulation of the guest power segment on the display parameters through the following nuclear health operations. ①MODE: Confirm / Select button ②V : Switch channel ③ : Increase button ⑤M: Menu / Return button...
Let Vekooto be your eyes! ---VEKOOTO 1. Remote Controller introduction (1).Standby: Power ON/OFF (2).Video Select: Channel switch (3).Menu: Go in setting page (4).Mode Select: Turn on / off recording (5).Function Down: Reduce when in setting page (6).Function Up: Increase when in setting page Note: Button cell model: CR2025 3V 2.
Page 5
Let Vekooto be your eyes! ---VEKOOTO 3. The wiring method when product use, as follows: (1) Connect Yellow wire to positive power(12-35V). (2) Connect Red wire to ACC. The red wire is connected to the car ignition wire ACC switch (which is the gear switch before starting up the car’s motor),...
Page 6
Let Vekooto be your eyes! ---VEKOOTO 5. About Trailer installation If you need to extend the cable for your trailer, please tell us via our email: Vekooto@outlook.com So we can send the extend cable for you, then you can extend it as the attached picture below shows, and you can disconnect them by Rotating the button of cable.
Page 7
Let Vekooto be your eyes! ---VEKOOTO 6. How to install the monitor and camera: ① Install the monitor (Ceiling bracket) Ceiling bracket ② Install the monitor brackets ③ Install the camera...
Let Vekooto be your eyes! ---VEKOOTO 7. Basic Function 7.1 Time Setting Time (1). Loop Video: 1/3/5/10min (2). Format: Format the TF card content and system. 7.2 Picture...
Page 9
Let Vekooto be your eyes! ---VEKOOTO 7.3 Playback Press the button Press Press twice choose AHD1 or AHD2 7.4 Split Setting Press button to switch between 4 split modes. 7.5 Function Press the butt on Press Turn On or Off Mirror...
Page 10
Let Vekooto be your eyes! ---VEKOOTO 8. MENU FAQ (1). How to return interface while viewing the Video List? A. Press the M/V button, then it can back to the monitor page. At other time, press the Menu button to go back the monitor page.
Need help?
Do you have a question about the N92 and is the answer not in the manual?
Questions and answers
Porque mi cámara no tiene señal, para **** el monitor
The VEKOOTO N92 camera may have no signal for the monitor due to the following reasons:
1. The camera system is not receiving power (it requires 12–35V).
2. The power cable or wire connections are loose or incorrect.
3. The pins on the monitor cable or the 4-pin camera cable may be bent, broken, or misaligned.
Check all power and cable connections carefully and ensure they are secure and correctly connected.
This answer is automatically generated
I’m trying to instal the N91 backup camera I have all the wires hooked up the red white and blue. Now on the large black aux wires there is a short red wire connected at each end what are those for? Do I need them hooked up to anything and if so where do I hook them up
The short red wire on the large black auxiliary wires for the VEKOOTO N92 backup camera is the ACC wire. It should be connected to the car ignition wire ACC switch. This connection allows the device to start automatically when the car key is turned on and turn off automatically when the vehicle key is turned off.
This answer is automatically generated