Related Manuals for AMPTO 220E
Summary of Contents for AMPTO 220E
- Page 1 VERTICAL GRAVITY SLICER, CE HOUSEHOLD, EXTRA CE EXECUTION GRAVITY SLICER 220E –250E -300E -350I USEANDMAINTENANCEMANUAL 100% Made in Italy...
- Page 2 I N D E X • GENERAL WARNINGS....................Page 4 • MANUFACTURER’S WARRANTY AND LIABILITY ............Page 11 • PACKAGING .......................Page 12 • PLATES - CONFORMITY MARKINGS ...............Page 13 • SCOPE OF SUPPLY AND ACCESSORIES..............Page 15 • TECHNICAL DESCRIPTION AND INTENDED CONDITIONS OF USE.....Page 15 •...
- Page 3 G E N E R A L W A R N I N G S Meaning of warning signs found in booklet DANGER: Indicates an imminently hazardous situation which, if not avoided, could result in serious injury or even death. The use of this term is limited to the most extreme situations.
- Page 4 G E N E R A L W A R N I N G S In case of a slicer sale, deliver this manual to the new owner too. ☞ The installation must be carried out according to the manufacturer’s instructions. Incorrect installation can cause harm to people, animals or properties in respect of which the manufacturer can not be held responsible.
- Page 5 G E N E R A L W A R N I N G S • Before plugging the appliance make sure that the data on the label correspond to those of the electrical distribution network. • The plate is on the bottom of the appliance. •...
- Page 6 G E N E R A L W A R N I N G S • If you decide not to use a device of this type any more, it must be made inoperative by cutting the power cord after removing the plug from the socket.
- Page 7 G E N E R A L W A R N I N G S ☞ Place the appliance on a horizontal and firm supporting plane, whose surface is not sensitive (eg. Lacquered furniture, tablecloths etc.). Make sure that the appliance is safely supported.
- Page 8 G E N E R A L W A R N I N G S Do not remove the safety devices and do not modify or exclude the mechanical and electrical safety devices. ☞ Always use protective scratchproof gloves for cleaning and maintenance.
- Page 9 G E N E R A L W A R N I N G S • Do not remove, cover or alter the rating plates fitted to the machine body and ensure their prompt replacement in case of damage. • Ensure that the product holder, receiving tray, surrounding areas and floor are kept clean and dry at all times.
-
Page 10: M A N U Fa Cturer's Warra N T Y A N D Liability
M A N U FA CTURER’S WARRA N T Y A N D LIABILITY • This device is guaranteed for 24 incorrect installation. months. failure to comply with the specific The purchase date must be proven with power techniques the relevant document. insufficient or incomplete periodic maintenance. - Page 11 P A C K A G I N G Check that all components spec- .1 - UNPACKAGING ified in the delivery note and this instruction booklet are present When taking delivery of the slicer, ensure and fully intact. that the packaging is fully intact; if this is •...
- Page 12 ☞ The packing components (bands, card- DO NOT DISPERSE board, polystyrene, etc.) are products THE PACKAGING assimilable to the urban solid refusals. PRODUCTS IN THE ENVIRONMENT! Fig. 1 P L A T E S - C O N F O R M I T Y M A R K I N G S The plate must never be re- The device described in this manual is produced in accordance with the...
- Page 13 ATTENZIONE OSSERVAREATTENTAMENTELE ISTRUZIONI PER L’INSTALLAZIONE, USO, PULIZIA E MANUTENZIONE FORNITE DALCOSTRUTTORE. Solo per versione “CE USO DOMESTICO” WARNING TYPE STRICTLY FOLLOW THE INSTRUCTIONS FROM THE MANUFACTURER FOR INSTALLA TION, USE, CLEANING N. XXXXXXXX /2014 AND MAINTENANCE. ATTENTION CE USO DOMESTICO RESPECTEZSTRICTEMENTLES INSTRUCTIONS DU FABRICANTCONCERNANTL’INSTALLA TION, MADE...
- Page 14 S C O P E O F S U P P L Y A N D A C C E S S O R I E S • Unless otherwise defined EC conformity declaration; • moment of order, the machines are instruction booklet for installation, use and maintenance.
- Page 15 2.3.b - Unexpected or improper use .2 - Environmental conditions of (NOT sliceable products) the machine use The following products CANNOT be • Temperature ..from -5 °C to + 40 °C sliced as they are liable to cause serious • Relative humidity ....
- Page 16 MECHANICAL SAFETY DEVICES AND ELECTRICAL PARTS • Plastic or aluminium crankcase panel Do not tamper, remove base protecting the electrical parts. nor bypass, under no • Transparent handguard mounted on the circumstances, the product tray. safety devices installed • Safety microswitch (excludes the on the equipment.
- Page 17 T E C H N I C A L S P E C I F I C A T I O N S 195E * 220E (mm) (mm) (mm) (mm) (mm) 13,5 Single-phase motor: 0,20 0,25 115-220-240V~ 50/60Hz Ø blade...
- Page 18 T E C H N I C A L S P E C I F I C A T I O N S 250 E (mm) (mm) (mm) (mm) (mm) 15,5 Single-phase motor: 0,30 115-220-240V~ 50/60Hz Ø blade (mm) Rpm: Slice thickness 0÷16 (mm)
- Page 19 T E C H N I C A L S P E C I F I C A T I O N S 300 E 350 I (mm) (mm) (mm) (mm) (mm) Single-phase motor: 0,35 0,50 115-220-240V~ 50/60Hz Ø blade (mm) (rpm) Slice thickness...
- Page 20 M A I N C O M P O N E N T S 9 12 Fig. 3...
- Page 21 1. Base 12. Product grip handle 2.Adjustable feet 3a. 13. Product grip handguard Startup button “I” 3b. 14. Tray handguard protection Switch “0/I” 15. Product tray handle 4. “STOP” “0” button 16. Blade plate tie-rod 5. Machine running warning light 17.
- Page 22 I N S T A L L A T I O N A N D P R E L I M I N A R Y C H E C K S .1 - Installation .3 - Control of operation and blade rotation direction Place the slicer on a well leveled, smooth, •...
- Page 23 Fig. 5 • Check the product tray (8) and the • Three-phase supply slicer: if the blade (11) rotates in the opposite product grip (10) smoothness. direction, immediately stop the machine by pressing the “0” button • Check the control knob (6) and the (4) or by turning the switch (3b) gauge plate (17) functioning and anticlockwise on “0/OFF”...
- Page 24 U S I N G T H E M A C H I N E .1 - Loading the product on the .2 - Slicing the products tray • Check that the slice thickness control • Adjust the slice thickness with the knob knob (6) is correctly placed on “0”.
- Page 25 C L E A N I N G T H E S L I C E R • Whenthe processing is over, remove the waste residuals from the collector surface (19). The machines must be accurately cleaned after use. After a shorter or longer period of inactivity clean the slicer before use.
- Page 26 “EXTRA CE” version “CE HOUSEHOLD USE” version • The product tray (8) can be easily • The machines are equipped with a rem oved by unscrewing the irremovable cap nut, as requested by corresponding support (7) placed under the European standard. it and by moving everything outward.
- Page 27 .3 - Cleaning the blade • Press on the blade with a wet cloth Fig. 8 (11) slowly rubbing moving from the inside to the outside (towards the gauge plate “17”). ALWAYS perform the blade cleaning (11) when the gauge plate (17) is close to the blade in safety position.
- Page 28 M A I N T E N A N C E .1 - Generalities In addition to the cleaning operations described in the previous paragraphs, it is necessary to perform some periodic maintenance operations to guarantee the slicer efficiency over time. The maintenance interventions allowed to the user are the following: •...
- Page 29 M A I N T E N A N C E .2 - Blade sharpening Accurately clean the machine as indicated in the previous paragraphs before proceeding with the operations. The sharpening can be performed until a decrease of 12 mm of the blade diameter nominal value. Beyond this value IT IS MANDATORY TO REPLACE THE BLADE, entrusting the operation EXCLUSIVELY to personnel authorized by the manufacturer.
- Page 30 • Remove the sharpener from the supplied bag. • Unscrew the knurled knob (23) and insert the threaded metallic pin in the hole (y) (specifically prepared on the product tray “8”). • Make sure that the two emery-wheels(x - x1) are pointedtowards the blade to be sharpened, easing the operation by pressing on the lower wheel “x1”...
- Page 31 • The lower wheel (x1) will have to remain inserted for almost half of its diameter between the blade, on which it will lean, and the regulator plane. • Insert the plug in the power socket and start the blade (with the appropriate command) while keeping the product tray (8) (and the sharpener) still through the handle (15).
- Page 32 P E R F O R M I N G T H E S H A R P E N I N G .2- Versions with built-in sharpener WARNING: Cutting hazard! Use protective cut- and tear- resistant gloves and perform all operations with extreme care. PA Y A TTENTION A T ALL TIMES ! For the blade sharpening to be performed periodically as soon as a decrease in the cutting capacity is felt, it necessary to observe the following instructions:...
- Page 33 P E R F O R M I N G T H E S H A R P E N I N G 3. Start the switch (1) and press the button (x2); 4. Let the blade rotate for about 30/40 seconds, then stop the blade by operating the switch (1) and, with a slight shift (using a pencil) to the outside of the blade, check if some burr has formed;...
- Page 34 P E R F O R M I N G T H E S H A R P E N I N G 6. After completing sharpening, we 7. Return the sharpener to its original advise cleaning the wheels using a position after the sharpening small brush soaked in alcohol;...
- Page 35 M O T O R B E L T T E N S I O N A D J U S T M E N T When, after a given time, the slicer emits an unusual noise because of the belt adjustment (30), proceed as follows: •...
- Page 36 T A K I N G T H E S L I C E R O U T O F S E R V I C E .1 - Correct procedure A machine compromises: • Aluminium-alloy frame. • Stainless-steel inserts and components. •...
-
Page 37: Troubleshooting
T R O U B L E S H O O T I N G • The following information are intended to aid in identifying and correcting defects and faults that may occur during use of the machine. ☞ Some failures can be resolved by the user; others require precise technical skills or special skills, and must be carried out by qualified personnel with recognized expertise and experience in the specific area of intervention. - Page 38 PROBLEM CAUSES SOLUTIONS Pressing the green or Do not use the machine Defective indicator. white button will start the with light indicator off; machine, but the operation promptly consult the light will not turn on. customer service. The machine starts but Defective Do not use the machine, vibrates, the motor is very...
- Page 39 G/V = Yellow/Green = Brown Only for personnel authorized by the manufacturer = Blue ELECTRICAL SCHEME CE DOM for versions: Condenser Tilting switch MOD.195 MF. 6,3 MOD.220 MF. 8 MOD.250E MF. 8 To the brown of the PA205 Mandarin micro pin Tighten MOTOR on slicer’s...
- Page 40 G/V = Yellow/Green = Brown Only for personnel authorized by the manufacturer = Blue ELECTRICAL SCHEME EXTRA CE for versions: F 195 - S 220- F 250 E - F 275 E - F 300 R Tilting bipolar switch MOTOR Condenser G/V B M MOD.195 MF 6,3...
- Page 41 S p a r e p a r t s...
- Page 42 220E - F300R...
- Page 43 220E F300R...
- Page 45 300E...
- Page 49 MOCADECLARA TION DECLARATION OF CONFORMITY OF THE MATERIALS AND OBJECTS DESTINED TO COME INTO CONTACT WITH FOOD PRODUCTS 1.With this document, it is declared that the product/article/machinery: VERTICAL GRAVITY SLICER WITH ANODISED ALUMINIUM STRUCTURE supplied for prolonged contact with foodstuffs; IS COMPLIANT WITH THE FOLLOWING EUROPEAN COMMUNITY LEGISLATION: •...
- Page 50 To perform the analysis, a specimen was put into contact with 5000 ml of water simulant for 2 hours at 40°C at third contact. Aluminium was searched for on the simulant coming from the contact using the ICP-MS technique. Unit of Limit of Component Result...
- Page 51 For slicer models with details in olive wood, the following tests were performed: Screening of inorganic compounds in materials in contact with the foodstuffs with the purpose of detecting and quantifying the molecules extractable from the sample by contact with 65% nitric acid at 120°C for 2 hours and detectable by plasma emission spectrometry (ICP/ OES).
- Page 52 MOCADECLARA TION DECLARATION OF CONFORMITY OF THE MATERIALS AND OBJECTS DESTINED TO COME INTO CONTACT WITH FOOD PRODUCTS 1.With this document, it is declared that the product/article/machinery: VERTICAL GRAVITY SLICER WITH PAINTED STRUCTURE FLYWHEEL supplied for prolonged contact with foodstuffs; IS COMPLIANT WITH THE FOLLOWING EUROPEAN COMMUNITY LEGISLATION: •...
- Page 53 Since the value detected is lower than the QM(t) value, the slice is deemed compliant. TEST CONDITIONS MIGRATION IN WATER MIGRATION IN OIL Met.: BS EN 1186:2006 Met.: BS EN 1186:2006 CONTACT CONDITIONS CONTACT CONDITIONS Surface/volume ratio: ........0,5 Surface/volume ratio: ........0,5 Time ............
- Page 54 For slicer models with details in olive wood, the following tests were performed: Screening of inorganic compounds in materials in contact with the foodstuffs with the purpose of detecting and quantifying the molecules extractable from the sample by contact with 65% nitric acid at 120°C for 2 hours and detectable by plasma emission spectrometry (ICP/ OES).
Need help?
Do you have a question about the 220E and is the answer not in the manual?
Questions and answers