Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ROLENCE ENTERPRISE ELiTEDENT Q-6
Summary of Contents for ROLENCE ENTERPRISE ELiTEDENT Q-6
- Page 1 User Manual Rolence LED Curing Light ® ELiTEDENT Instructions For Use ROLENCE ENTERPRISE INC. No. 18-3, Lane 231, Pu Chung Rd., Chungli, Taoyuan 32083, Taiwan. Tel: +886 3 4631999; Fax: +886 3 4631997; www.rolence.com.tw S-19-01-1133-U0001 V1.4...
-
Page 2: Table Of Contents
Table of Content No. Content Page Precautions And Safety Notes p. 3 Glossary of Symbols p. 4 Product Description & Fields of Application p. 5 Package Content p. 5 Technical Data p. 6 Charging base Hand piece Charging base and Handpiece Transportation and Storage Environment Installation of the unit p. -
Page 3: Precautions And Safety Notes
1. PRECAUTIONS AND SAFETY NOTES PLEASE NOTE! Prior to installation and start-up of the unit, carefully read the instructions provided herein! As with all technical devices, the proper function and safe operation of this unit depend on the user’s compliance with the safety recommendations presented in these operating instructions. CAUTION: This curing unit produces high curing energy output! A significant increase in curing energy is possible compared with conventional Halogen equipment you have previously used. -
Page 4: Glossary Of Symbols
of this product inconsistent with the Directions for Use is at the discretion and is the sole responsibility of the practitioner. 2. Keep solvents, flammable liquids, and sources of intense heat away from the unit as they may damage the plastic housing of the charger, the seals, or the cover on the operating buttons. 3. -
Page 5: Product Description & Fields Of Application
The ELiTEDENT Q-6 is a fast-curing LED curing light. It emits typical light energy output at about 1,200~1,400mW/cm². 5 seconds to cure most composite in the market with 2mm thickness. It also... -
Page 6: Technical Data
5. TECHNICAL DATA 5.1 Charging Base Operating voltage: INPUT: 100~240VAC, 0.5A , 50/60HZ OUTPUT(Adaptor) : 5V DC , 2A OUTPUT(Charging Base) : 4.2V DC , 1A Adaptor Brand: Fuhua Electronic, Model:UE15WCP1-050200SPA Dimensions Diameter: 95 mm Height: 69 mm Weight: Roughly 204 g 5.2 Handpiece Power supply: Lithium battery –... -
Page 7: Installation Of The Unit
6. INSTALLATION OF THE UNIT 6.1 Initial set-up NOTE: Upon receiving the LED Curing Light, check the packaging and parts for any possible damage that may have occurred in transit. If damage is apparent, please contact your authorized Rolence distributor from which the light was purchased. 1. -
Page 8: Keypad And Modes
Figure 4 NOTE: Verify the line plug of the power supply plug is properly rated for your facility, and that all connections comply with safe practices and all local requirements. Always use unit in conjunction with a properly grounded outlet. 6.2 Keypad and modes There are 2 buttons on the key pad for the mode/timer selection, and the on/off button. -
Page 9: Charging Base
There are 2 different modes to select from based on the procedure and the requirement. (Fig. 5) - Select the exposure time by pressing the mode button briefly. - While exposure is ongoing, the button for selection of the exposure time is inactive. (5s) –... -
Page 10: Operation Instruction
7. OPERATION INSTRUCTION Activating and Deactivating the Light: The light will enter “sleep” mode if the unit has not been used for more than 1 minute, the panel ► display will turn off to conserve power. If the panel display is not illuminated, simply press on/off button to bring it out of the sleep mode. -
Page 11: Operating Errors / Trouble Shooting
8. OPERATING ERRORS AND TROULE SHOOTING Problem Cause Solution ► No timer display on handpiece. The unit is in sleep mode. Press the on/off button to wake the unit. ► Can not activate/wake the light. Battery is drained. Please recharge battery, and try again. ►... -
Page 12: Service And Replacement Parts
Check light intensity with light checker on charging base The Elitedent Q-6 consists of a light intensity checker on charging base. Place the probe of light tip onto the window (See Figure 7) to ensure sufficient light energy provided for treatment prior to each curing. -
Page 13: Cleaning / Disinfecting / Sterilizing
10. Cleaning / Disinfecting / Sterilizing 10.1 Cleaning and Disinfection of Fiber Optic Light Guide Clean and disinfect the light guide before every use. The light guide is not sterile when delivered and ► must be sterilized before being used for the first time. Please check the manufacturer’s information about the cleaning and disinfecting agents. -
Page 14: Clean Charging Base, Handpiece, And Anti-Glare Cone
CAUTION: The charging base shall be unplugged before cleaning and disinfection of the charging base to prevent from electric shock. CAUTION: To immerse or spray the out surface of charging base and handpiece with water, cleanser and chemical disinfectant is not allowed as it may result in electric shock and damage of inner circuit board. -
Page 15: Warranty
(6) It is a consumption part. (This instruction subjects to change without pre-notice.) The equipment complies with the requirements in the Medical Device Directive 93/42 EEC. Rolence Enterprise Inc. No. 18-3, Lane 231, Pu Chung Rd., Chungli, Taoyuan 32083, Taiwan. - Page 16 S-19-01-1133-U0001 V1.4...
Need help?
Do you have a question about the ELiTEDENT Q-6 and is the answer not in the manual?
Questions and answers