Table of Contents
Advertisement
USING THE UNIT SAFELY
WARNING
Use only the supplied AC adaptor and the correct
voltage
Be sure to use only the AC adaptor supplied
with the unit. Also, make sure the line voltage
at the installation matches the input voltage
specified on the AC adaptor's body. Other AC
adaptors may use a different polarity, or be designed
for a different voltage, so their use could result in
damage, malfunction, or electric shock.
IMPORTANT NOTES
Placement
¹ Depending on the material and temperature of the
surface on which you place the unit, its rubber feet
may discolor or mar the surface.
Repairs and Data
¹ Before sending the unit away for repairs, be sure to
make a backup of the data stored within it; or you
may prefer to write down the needed information.
Although we will do our utmost to preserve the
data stored in your unit when we carry out repairs,
in some cases, such as when the memory section
is physically damaged, restoration of the stored
content may be impossible. Roland assumes no
liability concerning the restoration of any stored
content that has been lost.
Additional Precautions
¹ Any data stored within the unit can be lost as the
result of equipment failure, incorrect operation,
etc. To protect yourself against the irretrievable
loss of data, be sure to make a backup of the data
stored within it; or you may prefer to write down the
needed information.
¹ Roland assumes no liability concerning the
restoration of any stored content that has been lost.
¹ Never strike or apply strong pressure to the display.
¹ Do not use connection cables that contain a built-in
resistor.
Using External Memories
¹ Please observe the following precautions when
handling external memory devices. Also, make sure
to carefully observe all the precautions that were
supplied with the external memory device.
– Do not remove the device while reading/writing
is in progress.
– To prevent damage from static electricity,
discharge all static electricity from your person
before handling the device.
Caution Regarding Radio Frequency Emissions
¹ The following actions may subject you to penalty
of law.
– Disassembling or modifying this device.
– Removing the certification label affixed to the
back of this device.
– Using this device in a country other than where it
was purchased
10
CAUTION
Handle the ground terminal carefully
If you remove the screw from the ground
terminal, be sure to replace it; don't leave it
lying around where it could accidentally be
swallowed by small children. When refastening
the screw, make that it is firmly fastened, so it won't
come loose.
Intellectual Property Right
¹ It is forbidden by law to make an audio recording,
video recording, copy or revision of a third party's
copyrighted work (musical work, video work,
broadcast, live performance, or other work), whether
in whole or in part, and distribute, sell, lease,
perform or broadcast it without the permission of
the copyright owner.
¹ Do not use this product for purposes that could
infringe on a copyright held by a third party. We
assume no responsibility whatsoever with regard to
any infringements of third-party copyrights arising
through your use of this product.
¹ The copyright of content in this product (the sound
waveform data, style data, accompaniment patterns,
phrase data, audio loops and image data) is reserved
by Roland Corporation.
¹ Purchasers of this product are permitted to utilize
said content (except song data such as Demo
Songs) for the creating, performing, recording and
distributing original musical works.
¹ Purchasers of this product are NOT permitted to
extract said content in original or modified form, for
the purpose of distributing recorded medium of said
content or making them available on a computer
network.
¹ The SD logo
, SDHC logo
are trademarks of SD-3C, LLC.
¹ ASIO is a trademark and software of Steinberg Media
Technologies GmbH.
¹ This product contains eParts integrated software
platform of eSOL Co.,Ltd. eParts is a trademark of
eSOL Co., Ltd. in Japan.
¹ The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by Roland is under license.
¹ This product includes third party open source
software.
Copyright © 2009-2021 ARM Limited. All rights
reserved.
Licensed under the Apache License, Version 2.0 (the
"License");
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Copyright © 2016 Freescale Semiconductor, Inc.
Copyright © 2016-2021 NXP. All rights reserved.
Licensed under the BSD-3-Clause;
You may obtain a copy of the License at
https://opensource.org/licenses/BSD-3-Clause
Copyright © 2020 Amazon.com, Inc. or its affiliates.
All Rights Reserved.
Licensed under the MIT license
https://opensource.org/licenses/mit-license.php
This product's software is based in part on the work
of the Independent JPEG Group.
Precautions concerning use of phantom power
supply
Always turn the phantom power off when
connecting any device other than condenser
microphones that require phantom power.
You risk causing damage if you mistakenly supply
phantom power to dynamic microphones, audio
playback devices, or other devices that don't require
such power. Be sure to check the specifications of
any microphone you intend to use by referring to the
manual that came with it.
(This instrument's phantom power: 48 V DC, 10 mA Max)
¹ Roland and BOSS are either registered trademarks
or trademarks of Roland Corporation in the United
States and/or other countries.
¹ Company names and product names appearing
in this document are registered trademarks or
trademarks of their respective owners.
and SDXC logo
CAUTION
Advertisement
Table of Contents
