Page 1: Table Of Contents
LEDs 11 Production Date 11 Automated Logic Corporation • 1150 Roberts Blvd. • Kennesaw, GA 30144 • 770/429-3000 • 770/429-3001 Fax • www.automatedlogic.com • Copyright 2002 Automated Logic Corporation. All rights reserved. Automated Logic, the Automated Logic logo, SuperVision, Eikon, WebCTRL, Alert, and InterOp are registered trademarks of Automated Logic ®...
Page 2: Using The U141V
Line modules must be created in Eikon for RAM, 8KB non-volatile storage for default algorithm and configuration data. WebCTRL or Eikon using the Zone GFB option; refer to the Eikon for WebCTRL User’s Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 3: Job Start-Up
• UNI/16 with the U1M module driver, U-Line GFB can be downloaded from UNI/30 with the U3M module driver, Automated Logic Corporation’s web site UNI/32 with the UNM module driver, or (http://www.automatedlogic.com). You can UNI/59 with the U5M module driver also order a copy of Eikon for WebCTRL or Eikon on CD through Order Administration.
Page 4: Start-Up Checklist
D a m p e r S h a f t switch corresponds to the ones digit (see Figure 2. U141v+ Placement on VAV Box Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 5: Power Wiring
4. Turn the 24VAC power source on. You can power several modules from the 5. Make sure that 24VAC is present at the same transformer by daisy-chaining the module’s power input terminals. Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 6: Communications Wiring
The LogiStat Port connection does not apply module and is automatically detected by the in WebCTRL. U141v+. You can set or change the Unet baud rate to 9600 bps or 38.4 kbps on the UNI. The Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 7: Input Wiring
The U141v+ inputs support the types of Pro will not respond to input from the signals listed below. The LogiStat, LogiStat keypad. Plus, and LogiStat Pro sensors are supported through the module’s LogiStat port. Refer to Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 8: Using The Logistat
LogiStat, LogiStat Plus, or LogiStat Pro to DO-1 24VAC the U141v+. BUSS Automated Logic Corporation recommends a Figure 12. Digital Output Wiring specific wire to connect the U141v+ to the LogiStat. This 22AWG solid copper wire is Be sure the module’s power is off before available from Magnum Cable Corporation, connecting any inputs or outputs.
Page 9: Analog Output Wiring
AO-1 making the GFB. Figure 13. Analog Output Wiring A sample U-Line GFB is available at Automated Logic Corporation’s web site Be sure the U141v+’s power is off before (http://www.automatedlogic.com). Use this wiring any inputs or outputs. Connect the sample as a guideline for creating your own output wiring to the screw terminals on the GFBs.
Page 10: Point Identifiers
SuperVision or Eikon. Type field and enter the number of the input or output. If needed, enter an expander number. To scale a linear signal type, enter Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...
Page 11: Leds
Rx - On when the module receives data. Tx - On when the module transmits data. DO1 - On when digital output 1 is active. CW - On when actuator motor turns clockwise. Revised 8/14/02 • U141v+ © 2002 Automated Logic Corporation...

Automated Logic U141v+ Technical Instructions

Quick Links

Need help?

Questions and answers

Related Manuals for Automated Logic U141v+

Summary of Contents for Automated Logic U141v+

Table of Contents