Radarsign TC-800 Operation Manual
Radar speed sign
Hide thumbs
Also See for TC-800:
- Installation manual (16 pages) ,
- Installation manual (15 pages) ,
- Instruction manual (17 pages)
Related Manuals for Radarsign TC-800
Summary of Contents for Radarsign TC-800
- Page 1 TC-800 | TC-1100 Radar Speed Sign Operation Manual © 2005-2023 Radarsign, LLC All Rights Reserved 1 of 15 Radar Speed Sign Operation Manual_MN0036 v23.01...
-
Page 2: Table Of Contents
Password: safety Radarsign, LLC reserves the right to change the specifications without notice. Contact our sales department for special applications and configurations. © 2005-2023 Radarsign, LLC. 2 of 15 Radar Speed Sign Operation Manual_MN0036 v23.01... -
Page 3: Password Notification Card
Communication Commission (FCC) rules as shipped from the factory. The Radarsign™ device must not be opened or modified with the exception of the connection of the solar panel on solar powered models or AC power connections on AC powered models. -
Page 4: Safety Warnings
SAFETY WARNINGS This list of warnings indicate a potentially hazardous situation which if not avoided will result in death or serious injury, and/or property damage. ELECTRICAL SAFETY To reduce the risk associated with electric shock resulting from contacting high voltage AC: Turn power OFF before connecting wiring from our AC powered radar signs to the AC source. -
Page 5: Wi-Fi Setup
Wi-Fi Setup IMPORTANT: To configure your sign you will first need to connect to the Radarsign Wi-Fi. The radar speed sign emits its own wi-fi signal so no internet is required to connect to the sign. Either scan the QR codes on the Password Notification card included with your sign or manually set up per the instructions below. -
Page 6: Basic Sign Setup And Configuration
Basic Sign Setup When the HOME configuration screen opens, it will display the current settings of the radar speed sign. The alert settings and advanced functions available will vary depending on the your sign model and the sign options you purchased. 6 of 15 Radar Speed Sign Operation Manual_MN0036 v23.01... - Page 7 C) Change Password - Allows you to re-set the Wi-Fi password to something other than the default. If you change the default password, make sure you record it. Radarsign will not have a record of changed passwords. If lost you will need to reset to factory settings to create a new password.
-
Page 8: Alert Setup
Alert Setup NOTE: The alert settings and advanced functions available will vary depending on the your sign model and the sign options you purchased. Alert 1 Alert 1 Speed: • Enter the speed that you want the display to activate. Display Behavior •... -
Page 9: Advanced Functions
Choose from BOLD font, full brightness, or lower brightness for LED display. 5) Diagnostics: This tool downloads a diagnostic file to help Radarsign troubleshoot sign issues. Do not run Diagnostics unless directed to by Radarsign Customer Support. 6) Set Defaults: Sets sign to baseline sign settings. -
Page 10: Standard Timers
If you purchased the Streetsmart option, please refer to the Streetsmart Operation Manual for data collection and reporting instructions which can be downloaded from our Customer Resource Center. https://www.radarsign.com/customer-resource -center/ Password: safety 10 of 15 Radar Speed Sign Operation Manual_MN0036 v23.01... -
Page 11: Appendix A: Relay Switch Option
Appendix A | Relay Switch Option Overview The interface board on the TC-800 | TC-1100 allows users to connect the radar speed sign to external devices. The interface board has two relay outputs (connectors shown in green) and one input (connector shown in blue). -
Page 12: Speed Activated Relays
Appendix A | Relay Switch Option (cont’d) On the HOME configuration page ensure the Trigger box is checked. Click Set Config. The settings shown on the Trigger Settings screen will now take effect whenever a trigger event is detected (whenever >12V is detected on the trig- ger input). -
Page 13: Timer Activated Relays
Appendix A | Relay Switch Option (cont’d) Timer configuration page Timer Activated Relays Relays can also be configured to close at a certain time using the Timer features. On the Timer configuration screen, there is an Output Relay Override option. Enabling these options forces the relay output(s) on for the entire duration of the timer. -
Page 14: Hyper-Alerts
Appendix A | Relay Switch Option (cont’d) Hyper-Alerts™ Hyper-Alerts™ can be configured to activate at a given speed using the alert settings in the HOME configuration screen. In the example shown, Beacon Mode is enabled for Alert 2. If a car is traveling over 35 MPH, the Alert 2 settings take over and the Hyper-Alerts™... -
Page 15: Warranty
Replacement parts are covered by the unexpired warranty of the parts they replace. • Claims made under this warranty will be honored only if Radarsign, LLC is notified of a failure within the warranty • period, reasonable information requested by Radarsign is provided, and Radarsign is allowed to verify the cause of the failure.