Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar KSO 850
Summary of Contents for Holzstar KSO 850
- Page 1 Instruction Manual Edge milling machine KSO 850 230 V KSO 850 400 V KSO 850...
-
Page 2: Table Of Contents
11 Troubleshooting........17 Subject to technical modifications and error. 12 Spare parts .......... 18 12.1 Ordering spare parts........18 12.2 Spare parts drawing KSO 850 ....... 19 13 Electrical diagrams ......20 14 EC-Declaration of Conformity.... 21 KSO 850 | Version 2.08... -
Page 3: Introduction
Spare part orders: Fax: 0951 96555-119 E-Mail: ersatzteile@stuermer-maschinen.de We are always interested in valuable experience and knowledge gained from using the application, which then could be shared and be valuable to develop our products even further. KSO 850 | Version 2.08... -
Page 4: Obligations Of The Operating Company
KSO 850 | Version 2.08... -
Page 5: Qualification Of Personnel
Certain works may only be performed by specialist per- sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. Please contact our cus- tomer service for the execution of all arising work. KSO 850 | Version 2.08... -
Page 6: Safety Signs On The Machine
After eliminating the cause of the overload and waiting for the engine to cool down completely, the engine can be restarted. Fig. 3: Work space KSO 850 | Version 2.08... -
Page 7: General Safety Instructions
Intended Use - Keep the workplace and the floor in the vicinity of The KSO 850 edge milling machine is designed exclusi- the edge grinding machine free of any objects that vely for sanding wood and wood-like materials (fiber-... -
Page 8: Reasonably Foreseeable Misapplication
Fig. 4: Type plate KSO 850 / 230V - Impairment of hearing during prolonged work without hearing protection or if this is defective. -
Page 9: Transport, Packaging, Storage
The packaging material must not get into the hands of children, as some plastic packaging may present a suf- focation hazard when used as a toy. KSO 850 | Version 2.08... -
Page 10: Storage
Step 2: Insert the side table into the carrier and clamp it 6 EMERGENCY STOP button to the desired height with the clamping levers 7 Substructure with frame (see Fig. 6). 8 Suction connection 9 Clamping lever 10 Clamping screw 11 Degree scale KSO 850 | Version 2.08... -
Page 11: Electrical Connection
Only operate the edge sanding machine with an Step 4: Secure the set position with the clamping lever. electrical power supply that meets the following require- ments: KSO 850 | Version 2.08... -
Page 12: Adjustment And Set-Up Work
Step 5: Switch on the machine and the extraction and carry out the grinding process. Step 6: After completing the grinding process, press the red STOP button and switch off the extraction system. Disconnect the mains plug of the edge grinding machine. KSO 850 | Version 2.08... -
Page 13: Starting The Machine
(Fig. 12). piece feed is done by hand. The edge grinding machine KSO 850 can be used for edge grinding, surface grinding and hollow grinding. The oscillation of the sanding belt ensures even sanding belt stress and prevents grinding grooves on the workpiece. - Page 14 A after reaching the desired angle. each adjustment and set-up procedure. Briefly start the engine compartment and start the belt- Step 4: Adjust the table height to the appropriate position check (Fig. 14). to the sanding belt KSO 850 | Version 2.08...
-
Page 15: Care, Maintenance And Repair
Step 3: Switch off the edge sanding machine again. safety instructions. The edge sanding machine is ready for operation. 9.2.2 Sanding belt The sanding belt is a wearing part, which must be regu- larly checked for faults and replaced when worn. KSO 850 | Version 2.08... -
Page 16: Disposal Instructions / Recycling Facilities
Step 1: Remove all environmentally hazardous fluids into national law, used electric tools and electrical machi- from the old device. nes must be collected separately and recycled in an env- ironmentally sound manner. KSO 850 | Version 2.08... -
Page 17: Disposal Of Lubricants
1. The sanding belt is worn or added with 1. Change the sanding belt. during processing. sanding dust. 2. Excessive contact pressure is ap- 2. Reduce the contact pressure. plied to the workpiece on the grinding surface. KSO 850 | Version 2.08... -
Page 18: Spare Parts
Spare parts 12 Spare parts Example The engine for the Edge milling machine KSO 850 400V DANGER! must be ordered. The engine has the number 71 in the Danger of injury by the use of spare parts drawing 1. wrong spare parts! -
Page 19: Spare Parts Drawing Kso 850
Spare parts 12.2 Spare parts drawing KSO 850 The following drawing is intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 16: Spare parts drawing... -
Page 20: Electrical Diagrams
Electrical diagrams 13 Electrical diagrams 230 V Model 400 V Model Fig. 18: Electrical diagram 230 V Fig. 17: Electrical diagram 400 V KSO 850 | Version 2.08... -
Page 21: Ec-Declaration Of Conformity
D-96103 Hallstadt hereby declares that the following product Product Group: Holzstar® Woodworking machines Machine type: Edge milling machine Designation of the machine *: KSO 850 / 400 V Item number *: 5900850 KSO 850 / 230V 5900851 Serial number*: ___________________... - Page 22 www.holzstar.de...
Need help?
Do you have a question about the KSO 850 and is the answer not in the manual?
Questions and answers