Holzstar KSO 790 Instruction Manual

Holzstar KSO 790 Instruction Manual

Hide thumbs Also See for KSO 790:

Advertisement

Quick Links

Instruction manual
Edge milling machine
KSO 790
KSO 790
230 V
400 V
KSO 790

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KSO 790 and is the answer not in the manual?

Questions and answers

Summary of Contents for Holzstar KSO 790

  • Page 1 Instruction manual Edge milling machine KSO 790 230 V KSO 790 400 V KSO 790...
  • Page 2: Table Of Contents

    Copyright © 2020 Stürmer Maschinen GmbH, Hallstadt, 13.1 Ordering spare parts........16 Germany. 13.2 Spare parts drawing KSO 790 ....... 17 14 Wiring diagram ........... 18 The contents of these operating instructions is the sole 15 EC Declaration of Conformity ....19 property of the company Stürmer Maschinen GmbH.
  • Page 3: Introduction

    KSO 790 | Version 3.02...
  • Page 4: Obligations Of The Operating Company

    KSO 790 | Version 3.02...
  • Page 5: Qualification Of Personnel

    Certain works may only be performed by specialist per- sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. Please contact our cus- tomer service for the execution of all arising work. KSO 790 | Version 3.02...
  • Page 6: Safety Signs On The Machine

    After eliminating the cause of the overload and waiting for the engine to cool down completely, the engine can Fig. 3: Work space be restarted. KSO 790 | Version 3.02...
  • Page 7: Regulations For Safety And Accident Prevention

    Personal protection During operation safety glasses, gloves and head pro- tection should be worn. The Edge milling machine KSO 790 is designed for woodworking and not for the treatment of flammable or harmful substances. The customer is responsible for the choice of the material to be processed.
  • Page 8: Technical Data

    WARNING! The use of unstable lifting and load suspension equipment that might break under load can cause Fig. 4: Type plate KSO 790 severe injuries or even death. Check that the lifting and load suspension gear has sufficient load-bea- ring capacity and that it is in perfect condition.
  • Page 9: Packaging

    Fig. 5: Edge milling machine 1 Sanding belt 2 Engine 3 Clamping screw for height adjustment of the work- bench 4 Work table 5 ON and OFF switch 6 Substructure 7 Suction connection KSO 790 | Version 3.02...
  • Page 10: Specification And Standard Equipment

    - Do not operate machines that cause dust and chips near the machine. - There must be sufficient space for the operating personnel, for material transport as well as for ad- justment and maintenance work. - The site must have good lighting. KSO 790 | Version 3.02...
  • Page 11: Commissioning

    The edge grinding ma- chine KSO 790 can be used for edge grinding, surface - Make sure the electrical connection is correct grinding and hollow grinding. The sanding unit can be used horizontally and vertically.
  • Page 12: Adjustment And Set-Up Work

    To tension the sanding belt, lay the tension lever again. Fold up the protective cover and tighten the clamping screw. Put the suction nozzle and the sanding stopper back on the sanding belt and tighten the nut. KSO 790 | Version 3.02...
  • Page 13: Care, Maintenance And Repair

    Wearing safety gloves! Wear protective clothing! NOTE! Never use harsh cleaning agents for cleaning. This can lead to damage or destruction of the device. Screw Fig. 13: Adjustment of the cross table KSO 790 | Version 3.02...
  • Page 14: Regular Checks

    Then apply a thin layer of oil or grease to the moving parts. Lubricate the slide rails with grease. Sanding belt Fig. 15: Check the sanding belt KSO 790 | Version 3.02...
  • Page 15: Maintenance And Repair

    Only pass on the packaging material in such a way that it can be directly recycled. KSO 790 | Version 3.02...
  • Page 16: Troubleshooting

    Example Using non-approved spare parts voids the manu- facturer's warranty. The drive belt for the Edge milling machine KSO 790 400V must be ordered. The drive belt has the number 41 in the spare parts drawing 1.By ordering spare parts, 13.1Ordering spare parts...
  • Page 17: Spare Parts Drawing Kso 790

    Spare parts 13.2Spare parts drawing KSO 790 The following drawing is intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 17: Spare parts Drawing...
  • Page 18: Wiring Diagram

    Wiring diagram 14 Wiring diagram Fig. 18: Wiring diagram KSO 790 230V Fig:19 Wiring diagram KSO 790 400V KSO 790 | Version 3.02...
  • Page 19: Ec Declaration Of Conformity

    (ISO 12100:2010) DIN EN 60204-1:2014 Safety of machinery - Electrical equipment of machines - Part 1: General requirements Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Straße 26, D-96103 Hallstadt Hallstadt, 10.07.2016 ______________________ Kilian Stürmer Manager KSO 790 | Version 3.02...
  • Page 20 www.holzstar.de...

This manual is also suitable for:

59007905900791

Table of Contents