Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar DKS 504 Vario
Summary of Contents for Holzstar DKS 504 Vario
- Page 1 Instruction Manual JIG SAW DKS 504 Vario DKS 504 Vario...
-
Page 2: Table Of Contents
12 Spare parts .......... 19 12.1 Ordering spare parts........19 Subject to technical changes and errors. 12.2 Spare parts drawing DKS 504 Vario....20 13 Electrical Wiring Diagram....21 14 EC-Declaration of Conformity.... 22 DKS 504 Vario | Version 1.03... -
Page 3: Introduction
WARNING! This combination of symbol and signal term indica- tes a immediate dangerous situation which may cause death or serious injury if not averted. DKS 504 Vario | Version 1.03... -
Page 4: Operator Responsibility
In this process, the following shall apply in particu- have been impaired shall not be authorized, e.g. drug lar: users, users under the influence of alcohol or medica- tion. These operating instructions specify the following perso- nal qualifications for the different tasks: DKS 504 Vario | Version 1.03... -
Page 5: Personal Protective Equipment
- Keep children and unauthorized personnel away from the power tool. Distractions can cause you to Protective gloves protect the hands from compo- lose control. nents with sharp objects as well as friction, abrasion, and deep-cut injuries. DKS 504 Vario | Version 1.03... - Page 6 A wrench or key attached to a rotating part of the power tool may cause injury. - Make sure that the teeth of the blades point down to the table and that the blade tension is adjusted correctly. DKS 504 Vario | Version 1.03...
-
Page 7: Intended Use
Intended Use Intended Use Technical Data The JIG SAW DKS 504 Vario is used to saw edged wood 4.1 Table or wood-like workpieces, plastics and non-ferrous me- tals. The scroll saw cuts softwood, plastic and non-fer- Model DKS 504 Vario rous metals. -
Page 8: Type Plate
6.1 Illustration The illustrations in these operating instructions serve the general comprehension and may deviate from the actual type. Fig. 2: Type plate DKS 504 Vario Transport, packaging, storage 5.1 Transport Check the Jig Saw for visible transport damage upon de- livery. -
Page 9: Strokes And Saw Blade Selection
Do not overtighten the screws securing the base plate. The base plate must not be warped. 6.4 Optional accessories We recommend using only high-quality original Holzstar accessories. Faultless operation and optimal work re- Wear protective gloves! sults can only be guaranteed with original accessories. -
Page 10: Selection Of The Correct Saw Blade
If you are cutting workpieces that are thicker than 25 mm, you must insert the blade into the workpiece very slowly. Be especially careful not to bend or twist the blade when cutting. DKS 504 Vario | Version 1.03... -
Page 11: Clamp The Saw Blade
If precision work is required, a trial cut should be made and the grade adjusted if necessary. Fig. 10: Open the cover Step 3: Fold the saw blade guard up and loosen the saw blade (Fig.11). DKS 504 Vario | Version 1.03... -
Page 12: Align Saw Blade And Saw Table
DANGER! Always insert the saw blade so that the teeth point in the direction of the saw table. Fig. 15: Tilt the saw table Step 5: Retighten the table lock using the handle. DKS 504 Vario | Version 1.03... -
Page 13: Setting The Scale
- Never use blunt or damaged saw blades. Check that a residual current device (RCD). the appropriate saw blade is used. Step 1: Check that the JIG SAW is off. Step 2: Connect the machine to the mains. DKS 504 Vario | Version 1.03... -
Page 14: Workflow
Check nails or screws and remove if necessary. Fig. 19: Speed control Step 4: Select saw blade, clamp and check the moving Step 10: Guide the workpiece against the saw blade. parts for ease of movement. DKS 504 Vario | Version 1.03... -
Page 15: Carry Out Internal Cuts
Step 6: Carry out the cut. Step 7: After completing the internal cuts, remove the Fig. 21: Connect the worktool saw blade from the blade holders and remove the workpiece from the table. DKS 504 Vario | Version 1.03... -
Page 16: Change The Tools
- Always disconnect the mains plug before you start cleaning and maintenance works. - Connections and repairs of the electrical equipment may only be carried out by specialized electrical staff. DKS 504 Vario | Version 1.03... -
Page 17: Care After Working
If the extraction device does not work or is re- stricted, it must be restored. Only then can the Jig Saw To change the drive belt, proceed as follows: be put into operation. DKS 504 Vario | Version 1.03... -
Page 18: Troubleshooting
For the recycling process, please request the assistance of a specialized waste disposal centre if required. Step 2: If necessary, dismantle the machine into mana- geable and usable assemblies and components. DKS 504 Vario | Version 1.03... -
Page 19: Disposal Of Lubricants
- Type of device: JIG SAW DKS 504-Vario - Item number: 5902504 Tips and recommendations - Drawing number: 1 The manufacturer's warranty will become null and - Position number: 95 void if non admitted spare parts are being used. DKS 504 Vario | Version 1.03... -
Page 20: Spare Parts Drawing Dks 504 Vario
The following drawing are intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 26: Spare parts drawing JIG SAW DKS 504 Vario DKS 504 Vario | Version 1.03... -
Page 21: Electrical Wiring Diagram
Electrical Wiring Diagram 13 Electrical Wiring Diagram Fig. 27: Electrical Wiring Diagram DKS 504 Vario DKS 504 Vario | Version 1.03... -
Page 22: Ec-Declaration Of Conformity
<= 16 A per phase and not subject to conditional connection Kilian Stürmer, Stürmer Maschinen GmbH, Responsible for documentation: Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 25.01.2019 ______________________ Kilian Stürmer General Manager DKS 504 Vario | Version 1.03... - Page 23 Notes 15 Notes DKS 504 Vario | Version 1.03...
- Page 24 www.holzstar.de...
Need help?
Do you have a question about the DKS 504 Vario and is the answer not in the manual?
Questions and answers