Table of Contents
Advertisement
Quick Links
EDGE™ Port Replication Housing
P/N 003-991-AEN
Issue 5
related literature | Search www.corning.com/opcomm. Click on "Resources."
003-794-AEN
003-888-AEN
000-276-AEN
003-825-AEN
003-892-AEN
003-1049-AEN
000-274-AEN
003-885-AEN
006-407-QSG-AEN
1.
Carton Contents
•
EDGE™ port replication housing
(EDGE-10U-PRH) (Figure 1)
•
#12-24 x 0.5-in mounting screws (6)
2.
Tools and Materials
2.1
Standard Installation
•
Phillips screwdriver
•
Double-stack EDGE furcation plug cradles
(quantity one ships with each EDGE trunk)
2.2
Additional Solution Components
2.2.1 EDGE Solution
•
EDGE panel (EDGE-CP8B-PRH), up to 11 per
housing with up to eight EDGE modules per
panel
•
(Optional) Blank panel cover (EDGE-BLNK-PRH)
•
(Optional) Blank module cover (EDGE-CPCVR-PRH)
•
(Optional) LC adapter panel, aqua (EDGE-CP96-AD-PRH)
•
(Optional) LC adapter panel, blue (EDGE-CP96-AE-PRH)
EDGE™ Solution
EDGE Solution with 1U/2U/4U Fixed Trays
EDGE Secure Solutions FTTD Module
EDGE and EDGE8® Fiber Zone Boxes
EDGE and EDGE8 Solution Single Module Housing
EDGE Solution Single Module Housing for Splicing
EDGE Splice Cassette EDGE Field-Terminated Cassette
EDGE Solution Modules in an Enhanced Management Frame
Field Tool for MTP® PRO Connectors Quick Start Guide
Standard Recommended Procedure 003-991-AEN | Issue 5 | January 2021 | Page 1 of 8
TPA-4780
Figure 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CORNING EDGE-10U-PRH
Summary of Contents for CORNING EDGE-10U-PRH
- Page 1 EDGE™ Port Replication Housing P/N 003-991-AEN Issue 5 related literature | Search www.corning.com/opcomm. Click on “Resources.” 003-794-AEN EDGE™ Solution 003-888-AEN EDGE Solution with 1U/2U/4U Fixed Trays 000-276-AEN EDGE Secure Solutions FTTD Module 003-825-AEN EDGE and EDGE8® Fiber Zone Boxes 003-892-AEN...
- Page 2 2.2.2 EDGE8® Solution • EDGE8 panel (EDGE8-CP12B-PRH),up to 11 per housing with up to 12 EDGE8 modules per panel • (Optional) Blank panel cover (EDGE-BLNK-PRH) • (Optional) Blank-out EDGE8 module (EMOD8-BLANK) Mounting the Housing Step 1: Install two #12-24 x 0.5-in Phillips screws at desired height for the bottom of the housing (Figure 2).
- Page 3 Module cover Panel cover Figure 5 TPA-4784 NOTE: If installing less than eight modules in the EDGE™ tray, a blank module cover (EDGE-CPCVR-PRH), purchased separately, (shown in the inset in Figure 5) can be installed over two module positions in the EDGE tray.
- Page 4 Mount Trunk Cables in the Housing Step 1: Lift the latches on the rear door of the housing and remove the door (Figure 7). Step 2: Remove the appropriate cable entry cover by sliding it out the back of the housing (Figure 7).
- Page 5 Remove dust cover from the MTP® adapter. Also remove the MTP connector dust cap by pulling on the dust cap while holding the connector body. For the initial mating, do not clean or scope connectors. Corning® CleanAdvantage™ connectors are shipped with an optimized dust cap to maintain cleanliness for the first use.
- Page 6 Step 3: Mate the MTP connector into the adapter at the rear of the module. NOTE: When using the panel, you will install MTP trunks into the EDGE™ or EDGE8® modules. Figure 11 shows the EDGE modules MTP mating; EDGE8 modules are installed in the same manner. Figure 11 TPA-4785-B TPA-4786...
- Page 7 TPA-4789 Figure 12 10. Completing Installation Replace housing rear door (Figure 13) and secure with the latches. Figure 13 TPA-4792 Standard Recommended Procedure 003-991-AEN | Issue 5 | January 2021 | Page 7 of 8...
- Page 8 800-743-2675 • FAX: 828-325-5060 • International: +1-828-901-5000 • www.corning.com/opcomm Corning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without prior notification. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the properties of their respective owners.
Need help?
Do you have a question about the EDGE-10U-PRH and is the answer not in the manual?
Questions and answers