Wahl 8504L1, 8591L1 - 5-Star Cordless Senior Clipper Manual

IMPORTANT SAFEGUARDS

When using your electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS AND SAFEGUARDS BEFORE USING THIS APPLIANCE.

To reduce the risk of death or injury by electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately from the outlet. Note: Some electrical parts inside the appliance are electrically live, even with the switch "OFF."
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
4. Always unplug this appliance before cleaning.
5. Except when charging, always unplug this appliance from the electrical outlet immediately after using.

To reduce the risk of burns, electrical shock or injury to persons:

1. This appliance can be used by children aged from 14 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction, by a person responsible for their safety, concerning the use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has been dropped into water. Return the appliance to Wahl Clipper Corporation for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never operate the appliance with the air openings blocked or while on a soft combustible surface, such as a bed or couch, where air openings may be blocked. Keep the air openings (if any) free from lint, hair or the like.
6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Never drop or insert any object into any opening.
8. Do not use this appliance with a damaged or broken comb nor with teeth missing from the blades, as injury may occur. Before use, make certain blades are aligned properly. (See Clipper or Trimmer Care Instructions. May not be applicable for all appliances.)
9. During use, do not place or leave the appliance where it is expected to be subject to damage by an animal, or exposed to weather.
10. To disconnect, turn all controls to "OFF," then remove plug or charger from outlet.
11. Turn all controls to "OFF" before placing on or removing blades or attachments.
12. An appliance with a permanently attached cord should never be left unattended when plugged in.
13. Keep this appliance dry.
    
    For an appliance that has a rechargeable battery:
14. Do not crush, disassemble, heat above 100°C (212°F), or incinerate the appliance, due to risk of fire, explosion, or burns.
15. Use only the charger supplied by the manufacturer to recharge.
16. This charger is intended to be correctly orientated in a vertical or floor mount position.
17. Always attach plug to appliance first, then to outlet.
18. Use charge stand with Wahl products and power supplies only.

SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR COMMERCIAL USE ONLY

CLIPPER USE

USING CORD/CORDLESS CLIPPERS

If battery power is low, the power cord can attach directly to the unit for continued use as a corded unit.

CORDED OPERATION

• Attach power cord plug into clipper first, then to outlet. If your battery is completely run down, allow the unit to charge for 1 minute (switched OFF) before using as a corded unit. (Figure 1)
  
  
  
• If the cord is left attached to the clipper when not in use, the cord will automatically charge the clipper when left in the OFF position.

RECHARGING OPTIONS

• For units without a recharge stand, attach power cord plug into clipper first, then to outlet. Be sure clipper is switched OFF when charging. (Figure 1)
• For units with a recharge stand, place clipper in recharge stand so nameplate faces forward. (Figure 2)
  
  
  Attach power cord plug into recharge stand first, then to outlet. (Figure 3) (Not all units have a recharge stand.)
  

CHARGING THE BATTERY

Before the equipment is used for the first time, it should be charged 2 hours.
For recharging information, refer to Clipper Use Recharging Options.
Recommendation: The batteries should only be recharged when the performance of the equipment has deteriorated noticeably.

BATTERY OPERATION

Switch ON the unit using the ON/OFF switch and, after use, switch it OFF again. When the battery is fully charged, the unit can be used for up to 100 minutes.
(Exception: Cordless Senior run time is up to 80 minutes.)

LED INDICATOR

• Solid: LED will be fully lit in use or when the battery has reached full charge.
• Flashing: The battery has approximately 20% charge remaining.
• Pulse: While charging, LED will pulse until battery is fully charged. The LED will change to solid when the battery has a full charge.

TAPER LEVER

Some clippers are equipped with an adjustable taper lever that changes the closeness of your cut. When the lever is in the uppermost position, the blades will give the closest cut. Pushing the lever downward gradually increases the cutting length.

CLIPPER CARE

BLADE CARE AND OILING

In order to ensure that you get the most life and performance out of the clipper, we recommend oiling daily. To oil it properly, the clipper should be held so the blades are in a downward position as shown. Place one drop of Wahl oil in the center of the movable top blade and one drop of oil on each end of the top blade. Turn clipper switch ON and run to distribute the oil. When oil is evenly distributed, turn clipper OFF and wipe off excess oil with a soft cloth. Periodically oil heel of blade (shown in image) to reduce blade friction.
(USE WAHL OIL ONLY)

3 STEP SYSTEM

PERIODICALLY OIL HEEL OF BLADE

WIPE OFF EXCESS OIL so it does not run into the motor compartment.
Oil in the motor compartment will eventually lead to poor motor performance.
Blades should be oiled after using disinfectant or sanitizing solution.

DO NOT DIP OR SOAK the clipper or blades in any type of cleaning solution, disinfectant or oil. Excess liquid can deteriorate the unit's plastic components and seep into the motor compartment affecting motor life and performance. For proper care, follow the instructions under Clipper Care.

UNIT CARE

Use a clean cloth (dry or dampened with water).
DO NOT USE bleach, benzene or thinner to clean the unit.

CORD CARE

The cord should never be used to pull the clipper. Freedom of movement needs to be maintained. Care should be used to keep the cord untwisted, and undamaged. When stored, the cord should be coiled and placed neatly in a dry place.

ALIGNING 2 HOLE BLADES

Slightly loosen both blade screws at base of stationary blade, just enough to be able to shift the blade. Move blade adjustment lever to the full forward position. With the blade screws loosened, the bottom blade can be aligned with the top blade.

1. Points of the top blade teeth should be 1/32" to 1/16" (.79mm to 1.59mm) back and parallel to the points of the bottom blade teeth. This is important so the clipper doesn't cut too close or allow the moving top blade to touch the skin.
2. After blade is aligned, tighten screws.
3. Turn clipper switch ON and OFF a couple of times, and then recheck alignment of blades.

ALIGNING 3 HOLE BLADES

Slightly loosen the three blade screws of the stationary blade, just enough to be able to shift the blade. Move blade adjustment lever to the full forward position. With the blade screws loosened, the bottom blade can be aligned with the top blade.

1. Points of the top blade teeth should be 1/32" to 1/16" (.79mm to 1.59mm) back and parallel to the points of bottom blade teeth. This is important so the clipper doesn't cut too close or allow the moving top blade to touch the skin.
2. After blade is aligned, tighten screws.
3. Turn clipper switch ON and OFF a couple of times, and then recheck alignment of blades.

LITHIUM-ION BATTERY REPLACEMENT, CLIPPER DISPOSAL AND RECYCLING

• This unit uses a Lithium-Ion battery. For battery replacement send the entire, intact unit to:
  Wahl Service Center
  3001 North Locust Street
  Sterling, IL 61081
  
• Do not attempt to remove the battery. Lithium-Ion batteries can explode, catch fire, and/or cause burns if disassembled, damaged, or exposed to water or high temperatures.
• If you choose not to send the appliance in for battery replacement, the entire intact unit must be disposed. Do not attempt to remove the battery for disposal. Lithium-Ion batteries may be subject to local disposal regulations. Many locations prohibit disposal in standard waste receptacles. Check your local laws and regulations.
• For recycling contact a government recycling agency, waste disposal service, retailer, or visit online recycling sources, such as www.batteryrecycling.com or www.rbrc.org.

TROUBLESHOOTING

If your cord/cordless clipper does not seem to be operating or charging properly, please check the following:

• Check the outlet's current by plugging another appliance (one you know is in proper working condition) into the outlet.
• Make sure the unit is not connected to a power source that turns itself off when lights are turned off.
• Make sure the unit and power cord contacts are clean and free of hair or other contaminants.
• Verify that the blade assembly moves freely and is mounted properly.
• Unit's LED will flash quickly 5 times when excessive blade load has been detected. If this is detected, the unit will lock out and not power on. Switch off the unit. Inspect the blade set for any foreign objects or debris. Clean unit if anything is detected, oil the blades, and plug power cord into the unit to reset the lock out state. Switch on the unit. If the unit continues to flash 5 times and won't reset after following these instructions, contact Wahl Service Center. If flashing stops after resetting the clipper, disconnect cord to resume cordless operation.

If you still encounter problems with your unit, send your unit and recharging transformer to Wahl Clipper Corporation with a note explaining the problem.
Wahl Clipper Corporation offers a limited warranty on this product.
Please visit our website for full warranty terms.

For servicing, please ship your product prepaid to: Wahl Service Center 3001 North Locust Street Sterling, IL 61081

Documents / Resources

References

• http://www.rbrc.org

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Wahl 8504L1, 8591L1 - 5-Star Cordless Senior Clipper Manual