Related Manuals for CMP Brilliant Wonders CMP 25503 Series
Summary of Contents for CMP Brilliant Wonders CMP 25503 Series
- Page 1 BRILLIANT WONDERS LED BUBBLERS INSTALLATION INSTRUCTIONS CMP 25503 SERIES Brilliant Wonders LED BUBBLERS...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Product Overview………………………………………………………….….....3 1.1 Specifications……………………………………………………….……………3 1.2 Packing List……………………………………………………………....3 2. System Block Diagram………………………….………….…………………………3 3. Installation Guide………………………………………………………………...4 3.1 Mechanical Installation……………………………………………………..4 3.2 Electrical Installation…………………………………………………………..6 4. Electrical Schematic………………………………………………………………...…6 5. Operation Manual……………………………………………………....………7 5.1 Initial Setup……………………………………………………......7 5.2 Light Sequence Operation…………………………………………………..……8 5.3 Light Show Programs…………………………………………………………..8 6. -
Page 3: Product Overview
1. PRODUCT OVERVIEW 1.1 Specifications: o Color Source: RGB o Power input： 12.0 – 12.5 VAC o LED Life Expectancy: >50,000 hrs o Max Current： 1.6 Amps o Maximum Load Power: 20 Watts 1.2 Packing List o (1) Bubbler Unit • Housing • Lighting Unit available in 50, 100, or 150 ft options. -
Page 4: Installation Guide
There is also a 1” PVC slip socket on the bottom to run conduit for electrical connections. CMP recommends mounting the bubbler no more than 14” below the surface of the water for the best combination effect of water and light. If the bubbler is mounted on a vertical wall, the unit will act more like a lighted jet and will not give the same effect as a horizontal application. - Page 5 3.1.2 Complete the rough-in by plumbing the water line to the desired pumping system. Flush the water line prior to any startup to remove any foreign material from construction that may be inside the system. Be sure to install a ball valve in-line to adjust the height and flow of the water. After the system has been started, ad- just the height of the water using this valve to get the desired effect.
-
Page 6: Electrical Installation
3.2 Electrical Installation 3.2.1 With all of the different components and applications in the pool and spa industry, proper installation recommendations cannot be taken for granted. This procedure gives specific recommendations to ensure that electrical wiring of your Brilliant Wonders Lighted Bubbler Unit is properly installed. The installer should also consult local inspectors to insure that the unit is installed according to all local building codes and regu- lations. -
Page 7: Operation Manual
5. OPERATION MANUAL 5.1 Initial Startup NOTE: USE ONLY WATER THAT HAS BEEN PROPERLY FILTERED 5.1.1 The following check list should be made prior to startup. This includes initial construction startup and seasonal start up. o Remove the construction/debris cover from the Bubbler. o Visually inspect the unit to ensure that there is no debris in the nozzle. -
Page 8: Light Sequence Operation
5.2 Light Sequence Operation 5.2.1 The Brilliant Wonders Lighted Bubbler can be controlled using a standard wall-mount light switch. Multiple Brilliant Wonders Lighted Bubbler lights can be connected via a junction box to a single switch so that all lights can be switched on and off together. This will ensure that they will behave with the same lighting sequences. -
Page 9: Winterization
5.3.2.1 Synchronized Color Show Mode: The 9 colors that are available are brilliant white, amazing aqua, ocean blue, electric blue, light green, green, sunset yellow, pretty in pink and purple passion. Change to the next color by turning the light switch to the off position and then back on. 5.3.2.2 Show Program Mode: To get to the Program Modes, turn the unit off and then back on to ad- vance the sequence to the desired show. - Page 10 Brilliant Wonders LED BUBBLERS Toll Free: 800.733.9060 | www.c-m-p.com 0513sb...
Need help?
Do you have a question about the Brilliant Wonders CMP 25503 Series and is the answer not in the manual?
Questions and answers